Service bulletins for the 2012 Dodge Journey
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
224 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Transmission and driveline are shown. Show all
| 9004206 | 2020-06-22. Service bulletin. POWER TRAIN; ENGINE. Remanufactured Transmission Assembly 1. All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 3. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 4. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission. |
|---|---|
| V51 | 2020-01-21. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Customer Satisfaction Notification V51 Reprogram Powertrain Control Module |
| 18-058-19 REV. A | 2019-12-16. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. No Start After Powertrain Control Module (PCM) Replacement and/or Reprogramming |
| 18-066-15 | 2018-11-19. Service bulletin. ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM. Flash: Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with updated software. The technician may find the following Diagnostic Trouble Code (DTCs) set in the Powertrain Control Module (PCM) memory: ? U0140 - Lost Communication With Body Control Module. (3.6L engine only). NOTE: Attempting to clear this DTC will be unsuccessful. Some customers may experience any of the following: ? Continuous cycling of fuel pump relay when using remote start (3.6L engines) ? Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that P0108 - Manifold Absolute Pressure Sensor Circuit High has been set active or stored (3.6L engine) NOTE: MIL Illumination for P0108 - Manifold Absolute Pressure Sensor Circuit High affects only 2012 model year vehicles equipped with a 3.6L engine (sales code ERB). ? 1 - 2 upshift clunk or bump (2.4L & 3.6L engines) ? 3 - 4 harsh upshift at closed throttle after a WOT stab in 1st or 2nd gear (2.4L & 3.6L engines) ? 4 - 5 upshift clunk or bump (2.4L & 3.6L engines) ? 5 - 6 upshift clunk or bump (3.6L engine) ? 6 - 5 downshift clunk or bump (3.6L engine) ? 6 - 4 downshift clunk or bump (3.6L engine) ? RPM Fluctuating or Jerking feeling while operating in cruise control. Condition is more noticeable when the vehicle is going up and down grades(2.4L & 3.6L engines) ? 1 - 2 harsh upshift going down a grade (2.4L engine) ? 3 - 2 downshift clunk or bump (2.4L engine) ? 4 - 3 downshift clunk or bump (2.4L engine) ? Improves the consistency of how shifts are controlled during upshifts ?torque management? ? Delayed downshifts (3.6L engine) Updating the software will correct the conditions listed above. |
| 18-008-13 | 2018-06-11. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. Flash: MIL Illumination P0108 - Manifold Absolute Pressure Sensor Circuit High And Transmission Shift Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. The customer may experience any of the following: 3.6L engine. MIL Illumination for P0108 - Manifold Absolute Pressure Sensor Circuit High affects only 2012 model year vehicles equipped with a 3.6L engine (sales code ERB). 2.4L & 3.6L engines 2.4L & 3.6L engines 2.4L & 3.6L engines 3.6L engine 3.6L engine 3.6L engine 2.4L & 3.6L engines 2.4L engine 2.4L engine 2.4L engine Improves the consistency of how shifts are controlled during upshifts ?torque management?. 3.6L engineUpdating the software will correct the conditions listed above. |
| 18-006-13 | 2018-06-11. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Flash: Lack Of Acceleration Performance With The Accelerator Pedal Fully Pressed This bulletin involves flash reprogramming the Powertrain Control Module (PCM) with new software. Derate at wide open throttle. |
| 18-008-13 | 2018-06-04. Service bulletin. EQUIPMENT; ENGINE; POWER TRAIN; ELECTRICAL SYSTEM. Flash: MIL Illumination P0108 - Manifold Absolute Pressure Sensor Circuit High And Transmission Shift Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. The customer may experience any of the following: 3.6L engine. MIL Illumination for P0108 - Manifold Absolute Pressure Sensor Circuit High affects only 2012 model year vehicles equipped with a 3.6L engine (sales code ERB). 2.4L & 3.6L engines 2.4L & 3.6L engines 2.4L & 3.6L engines 3.6L engine 3.6L engine 3.6L engine 2.4L & 3.6L engines 2.4L engine 2.4L engine 2.4L engine Improves the consistency of how shifts are controlled during upshifts ?torque management?. 3.6L engine Updating the software will correct the conditions listed above. |
| 18-006-13 | 2018-06-04. Service bulletin. VEHICLE SPEED CONTROL:ACCELERATOR PEDAL; ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); EQUIPMENT. Flash: Lack Of Acceleration Performance With The Accelerator Pedal Fully Pressed This bulletin involves flash reprogramming the Powertrain Control Module (PCM) with new software. Derate at wide open throttle. |
| 18-024-12 REV. A | 2018-05-14. Service bulletin. POWER TRAIN; ENGINE. Flash: MIL Illumination P0108 - Manifold Absolute Pressure Sensor Circuit High And Transmission Shift Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. The customer may experience any of the following: 3.6L engine. MIL Illumination for P0108 - Manifold Absolute Pressure Sensor Circuit High affects 2012 model year vehicles only. 2.4L & 3.6L engines 2.4L & 3.6L engines 2.4L & 3.6L engines 3.6L engine 3.6L engine 3.6L engine 2.4L & 3.6L engines 2.4L engine 2.4L engine 2.4L engine Improves the consistency of how shifts are controlled during upshifts ?torque management?Updating the software will correct the condition listed above. |
| 18-032-12 | 2018-05-14. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Less Than Desired Acceleration From Idle This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. The customer may experience less than desired acceleration from idle. Updating the software will correct the condition listed above. |
| 18-008-13 | 2018-02-21. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: MIL Illumination P0108 - Manifold Absolute Pressure Sensor Circuit High And Transmission Shift Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. The customer may experience any of the following: 3.6L engine. MIL Illumination for P0108 - Manifold Absolute Pressure Sensor Circuit High affects only 2012 model year vehicles equipped with a 3.6L engine (sales code ERB). 2.4L & 3.6L engines 2.4L & 3.6L engines 2.4L & 3.6L engines 3.6L engine 3.6L engine 3.6L engine 2.4L & 3.6L engines 2.4L engine 2.4L engine 2.4L engine Improves the consistency of how shifts are controlled during upshifts ?torque management?. 3.6L engineUpdating the software will correct the conditions listed above. |
| 18-006-13 | 2018-02-21. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: Lack Of Acceleration Performance With The Accelerator Pedal Fully Pressed This bulletin involves flash reprogramming the Powertrain Control Module (PCM) with new software. Derate at wide open throttle. |
| 18-032-12 | 2018-02-21. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Less Than Desired Acceleration From Idle This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. The customer may experience less than desired acceleration from idle.Updating the software will correct the condition listed above. |
| 04726431A$ | 2016-09-15. Service bulletin. POWER TRAIN; POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE); WHEELS. "WHEEL ASSY - STEEL WHEN SERVICING A JOURNEY (JC) VEHICLE WITH STEEL WHEELS (WFU CODE) WITH OR WITHOUT A SHAKE OR VIBRATION COMPLAINT; PLEASE REVIEW THE 4 WHEEL ASSEMBLIES IN ORDER TO DETECT ANY WITNESS MARK OF A MISSING/MISPLACED WHEEL WEIGHT. ALSO PLEASE TRY TO REMOVE THE WEIGHTS WITH HAND FORCE ONLY. PLEASE INFORM KARLA DE LA ROSA MUNIVE (KARLA.DELAROSA@FCAGROUP.COM) HOW MANY WITNESS MARKS WERE SEEN, AND HOW MANY WEIGHTS WERE ABLE TO BE REMOVED WITH FORCE HAND,ON EACH WHEEL ASSEMBLY. ~ PLEASE CONTACT KARLA.DELAROSA@FCAGROUP.COM FOR FEEDBACK RELATED ONLY." |
| 18-050-16 REV. A | 2016-07-14. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). "FLASH: POWERTRAIN DIAGNOSTIC AND SYSTEM IMPROVEMENTS THIS BULLETIN INVOLVES SELECTIVELY ERASING AND REPROGRAMMING THE POWERTRAIN CONTROL MODULE (PCM) WITH NEW SOFTWARE. SYMPTOM/CONDITION: A SMALL NUMBER OF CUSTOMERS MAY EXPERIENCE A MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATION. UPON FURTHER INVESTIGATION THE TECHNICIAN MAY FIND ONE OR MORE OF THE FOLLOWING DIAGNOSTIC TROUBLE CODES (DTCS) SET IN THE PCM: JC VEHICLES 3.6L: · P0335 - CRANKSHAFT POSITION SENSOR CIRCUIT. · P2610 - PCM INTERNAL ENGINE OFF TIMER PERFORMANCE. · U0140 - LOST COMMUNICATION WITH BODY CONTROL MODULE (BCM). · P0456 - EVAP SYSTEM SMALL LEAK. · P0108 - MANIFOLD ABSOLUTE PRESSURE SENSOR CIRCUIT HIGH (2012 MY ONLY). THE FOLLOWING TRANSMISSION ENHANCEMENTS ARE ALSO INCLUDED IN THIS SOFTWARE UPDATE: · CONTINUOUS CYCLING OF FUEL PUMP RELAY WHEN USING REMOTE START. · 1 - 2 UPSHIFT CLUNK OR BUMP. · 3 - 4 HARSH UPSHIFT AT CLOSED THROTTLE AFTER A WOT STAB IN 1ST OR 2ND GEAR. · 4 - 5 UPSHIFT CLUNK OR BUMP. · 5 - 6 UPSHIFT CLUNK OR BUMP. · 5- 4 DOWNSHIFT CLUNK OR BUMP. · 6 - 5 DOWNSHIFT CLUNK OR BUMP. · RPM FLUCTUATING OR JERKING WHILE OPERATING IN CRUISE CONTROL. CONDITION IS MORE NOTICEABLE WHEN THE VEHICLE IS GOING UP AND DOWN GRADES. · IMPROVES THE CONSISTENCY OF HOW SHIFTS ARE CONTROLLED DURING UPSHIFTS “TORQUE MANAGEMENT”. · DELAYED DOWNSHIFTS. JC VEHICLES 2.4L: · **U0140 - LOST COMMUNICATION WITH BODY CONTROL MODULE (BCM).** · P0456 - EVAP SYSTEM SMALL LEAK. THE FOLLOWING TRANSMISSION ENHANCEMENTS ARE ALSO INCLUDED IN THIS SOFTWARE UPDATE: · 1 - 2 UPSHIFT CLUNK OR BUMP. · 3 - 4 HARSH UPSHIFT AT CLOSED THROTTLE AFTER A WOT STAB IN 1ST OR 2ND GEAR. · 4 - 5 UPSHIFT CLUNK OR BUMP. · RPM FLUCTUATING OR JERKING WHILE OPERATING IN CRUISE CONTROL. CONDITION IS MORE NOTICEABLE WHEN THE VEHICLE IS GOING UP AND DOWN GRADES. · 1 - 2 HARSH UPSHIFT GOING DOWN A GRADE. · 3 - 2 DOWNSHIFT CLUNK OR BUMP. · 4 - 3 DOWNSHIFT CLUNK OR BUMP. |
| 18-006-13 | 2016-04-26. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). SUMMARY TO BE PROVIDED ON A FUTURE DATE. |
| 06-001-12 | 2012-04-18. Service bulletin. POWER TRAIN:CLUTCH ASSEMBLY:PEDAL/HAND LEVER(MOTORCYCLE). DODGE: CLUTCH PEDAL IS INOPERATIVE. *KB |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.