# C0196 on the 2012 Chevrolet Volt

The bulletins listed name this code in NHTSA's summary, or are about the same components. A bulletin or a recall listed here may apply to the model year. None of it is a diagnosis.

Nobody has written a description of this code yet.

## Bulletins for this model year that name C0196

- [10246917](https://open.wenmarpro.com/bulletins/10246917), 2023-12-11: Service Stabilitrak DTC C0196 After Vehicle Has Been Transported.
- [10114543](https://open.wenmarpro.com/bulletins/10114543), 2017-08-15: This Preliminary Information communication advises the technician to insure that global diagnostic service 2 diagnostic packages are up to date prior to learning the steering angle sensor for a diagnostic trouble code C710 symptom code 71 set in the electronic brake control module or the power steering control module. When rechecking for diagnostic trouble codes a U0074 U0077, U0180D, U01293, U0126, U0125, C0186, C0196, or C0287 are set and will not clear diagnose the Chassis bus. If no fault is found in the chassis bus check for an multiple diagnostic interface to data link connector issue. Technician is to try a different multiple diagnostic interface cable and attempt the steering angle sensor learn again following service information instruction then try to clear the codes again.
- [10114437](https://open.wenmarpro.com/bulletins/10114437), 2017-08-15: This Preliminary Information communication provides information to the technician some vehicles may have a Service Stabilitrak message and a red brake lamp illuminated on the Instrument Panel Cluster. Technician may find a Diagnostic Trouble Code C0196 in the Electronic Brake Control Module. This concern may be preset after the vehicle was flat towed or just came off a car carrier. Technician will need to perform a Multi Axis sensor learn and a Diagnostic Trouble Code clear in the Electronic Brake Control Module. Then shut ignition off, open and close driver door and let vehicle sit for 3 minutes. After the vehicle has slept for 3 minutes start the vehicle and let it run in park for 10 seconds. Now the vehicle will need to be driven for 30 seconds over 20 miles per hour. If code is cleared and doesn't reset, release the vehicle to the customer. If code resets follow normal diagnosis in Service Information.
- [10112466](https://open.wenmarpro.com/bulletins/10112466), 2017-08-15: This Preliminary Information communication advises the technician to insure that global diagnostic service 2 diagnostic packages are up to date prior to learning the steering angle sensor for a diagnostic trouble code C710 symptom code 71 set in the electronic brake control module or the power steering control module. When rechecking for diagnostic trouble codes a U0074 U0077, U0180D, U01293, U0126, U0125, C0186, C0196, or C0287 are set and will not clear diagnose the Chassis bus. If no fault is found in the chassis bus check for an multiple diagnostic interface to data link connector issue. Technician is to try a different multiple diagnostic interface cable and attempt the steering angle sensor learn again following service information instruction then try to clear the codes again.
- [10111916](https://open.wenmarpro.com/bulletins/10111916), 2017-08-15: This Preliminary Information communication advises the technician to insure that global diagnostic service 2 diagnostic packages are up to date prior to learning the steering angle sensor for a diagnostic trouble code C710 symptom code 71 set in the electronic brake control module or the power steering control module. When rechecking for diagnostic trouble codes a U0074 U0077, U0180D, U01293, U0126, U0125, C0186, C0196, or C0287 are set and will not clear diagnose the Chassis bus. If no fault is found in the chassis bus check for an multiple diagnostic interface to data link connector issue. Technician is to try a different multiple diagnostic interface cable and attempt the steering angle sensor learn again following service information instruction then try to clear the codes again.
- [10111903](https://open.wenmarpro.com/bulletins/10111903), 2017-08-15: This Preliminary Information communication provides information to the technician some vehicles may have a Service Stabilitrak message and a red brake lamp illuminated on the Instrument Panel Cluster. Technician may find a Diagnostic Trouble Code C0196 in the Electronic Brake Control Module. This concern may be preset after the vehicle was flat towed or just came off a car carrier. Technician will need to perform a Multi Axis sensor learn and a Diagnostic Trouble Code clear in the Electronic Brake Control Module. Then shut ignition off, open and close driver door and let vehicle sit for 3 minutes. After the vehicle has slept for 3 minutes start the vehicle and let it run in park for 10 seconds. Now the vehicle will need to be driven for 30 seconds over 20 miles per hour. If code is cleared and doesn't reset, release the vehicle to the customer. If code resets follow normal diagnosis in Service Information.