WenmarOpen by Wenmar Pro

Service bulletins for the 2015 Chevrolet Tahoe

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

2584 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
PIP52112017-08-15. Service bulletin. ENGINE; STRUCTURE. This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair vehicles with a rough idle and/or vibration at idle in Drive. This condition will not be present in Park, or Neutral. This concern may be caused by ground out within the one or both engine mounts. Technician will use CH-51450-A (Pico Oscilloscope) to measure the vibration disturbance. If the vibration concern is E1.5 in the horizontal / lateral direction with Pico sensor mounted in seat track as indicated - continue with steps to reduce the amplitude of the vibration by adding spacers in key locations to reduce ground out within the engine mounts. The 6.2L engine has a characteristic E1 which can be felt, and may be described as a lopey idle. Do not confuse 6.2L E1 characteristic (not caused by mount ground-out), with E1.5 normal idle characteristics being transmitted into the truck via ground-out thru the engine mounts. If measuring high at the seat track 12 mg or greater; replacement of the engine mounts should help reduce the amplitude of the vibration. If the disturbance measures at the seat track as E 1.5 lateral in the range of approximately 2.5 - 8 mg using a tri-axis sensor. Then place tri-axis Pico sensor on the inboard seat track forward-most location to record measurement of the rough idle vibration concern. With the Heater-Vent-Air Conditioning on perform several short heavy launch events from stop to stop to bring the temperatures back up while attempting to re-create the rough idle vibration in Drive with Pico sensor placed on inboard seat track; while the vibration is active - Record Pico reading. This method seems to provide better results than extended test drives. If the Pico reading for E1.5, with vibration active, at specified seat track location measures close to 2mg or less use Service Information to diagnose rough idle / vibration. If the Pico reading for E1.5, with vibration active, at the inboard forward seat track
PIT5266B2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:12V/24V/48V BATTERY; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that during very cold ambient temperatures there may be a no crank or a click no crank condition. Technician will need to check the battery voltage while trying to crank the engine. Replace the battery if it fails the GR8 test. If the battery has more than 11.4 volts while starting and there is a click noise is heard, technician will need to replace the starter and the inspection cover.
PIP3119M2017-08-15. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.
PIP4670D2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE. This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
PIP5089A2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code C0569 that will not clear. Technician should be advised if there are any issues with the rotational position sensor, incremental position sensor, encoder motor, motor A or B circuits, rotational position sensor or incremental position sensor circuits when the transfer case control module attempts to determine location the location cannot be determined correctly.
PIP5175A2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING; WHEELS:LUGS/NUTS/BOLTS/STUDS; WHEELS; POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicles that may have a delayed engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th gears. This may be due to loose stator support to pump cover bolts causing a leak at the stator support to pump cover gasket. Technician will check for the bolts to be loose. If any of the bolts are loose or the gasket is misaligned or leaking, the transmission pump cover must be replaced and the 1234 clutch plates should be inspected for being distressed and repaired as needed.
PIP51752017-08-15. Service bulletin. PARKING BRAKE; ENGINE AND ENGINE COOLING; WHEELS:LUGS/NUTS/BOLTS/STUDS; POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicles that may have a delayed engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th gears. This may be due to loose stator support to pump cover bolts causing a leak at the stator support to pump cover gasket. Technician will check for the bolts to be loose. If any of the bolts are loose or the gasket is misaligned or leaking, the transmission pump cover must be replaced and the 1234 clutch plates should be inspected for being distressed and repaired as needed.
PIT5245A2017-08-15. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that the blower motor may be noisy or vibrate when running. This concern will only occur when the temperatures is below 32 degrees Fahrenheit and if the blower motor is removed while still cold, ice may be found on the blower motor cage. This concern could be caused by water leaking or snow ingestion into the Heater-Vent-Air Conditioning case. Technician is to perform normal water testing diagnostics while the Heater-Vent-Air Conditioning is running, looking for water leaking past the plenum cover. If water is leaking past the cover remove the cover and install a 12x12 snow resistant screen to the fresh air intake. Reseal and install the plenum cover cap using Kent air dry sealer or equivalent.
PIP51792017-08-15. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have extended or long crank time during cold ambient air temperatures. Direct Injection systems run at higher pressures, and the mechanical pump on the engine must build up the required pressure before the first injection event occurs. Direct Injection engines may have slightly longer cold crank times than that of port fuel engines.
PIP5174A2017-08-15. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician about vehicles that have an engine extended or long crank time during ambient air temps of ?18° Celsius (0° Fahrenheit) or colder when using E85 fuel. Technician will need to use Global Diagnostic System 2 to determine the actual ethanol content of the fuel. Adding regular fuel to the tank may help resolve the concern.
PIP5130C2017-08-15. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician how to diagnose and repair vehicles with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. Technician will need to use Global Diagnostic System 2 to actuate the cam phaser solenoid 4 or 5 times then try starting the vehicle. Then disable the ignition and fuel system. After the ignition and fuel system are disabled try to start the engine. Technician can now unplug the camshaft actuator to perform the following. Install a 20A fused jumper wire between the terminal 2 and 12V. Tickle/tap the low reference terminal 1 to ground on the cam actuator magnet, while cranking the engine over. When the engine starts and runs the cam actuator or oil control valve does not need to be replaced.
PIP5109D2017-08-15. Service bulletin. ENGINE; ELECTRICAL SYSTEM. This Preliminary Information communication advises the technician that the Engine Control Module part number 12656993 will be placed on restriction through the General Motors Product Quality Center. Dealer will need to contact General Motors Product Quality Center for further assistance.
PIP5130D2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician how to diagnose and repair a vehicles with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. If the vehicle is a crank no start, perform PIE0295.
PIP51892017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician about vehicle that may have black smoke on a cold start. A dual-pulse injection strategy is utilized during engine cold start to reduce the time required to bring the catalytic converter up to operating temperature. This split injection strategy lasts for about 60 seconds on cold start. This process may cause the customer to see increased black smoke during cold start and should be considered normal.
PIP4138P2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
PIP5252A2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that the engine may run hot with the snow plow installed. Do not exceed 64 kilometers per hour / 40 miles per hour with a snow plow mounted to the vehicle even if equipped with VYU. The vehicle could overheat and be damaged.
PIT5391C2017-08-15. Service bulletin. ENGINE; ELECTRICAL SYSTEM:WIRING. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be on when the ignition is in the run position. Technician may find Diagnostic Trouble Codes P0513 and or P262B may also be set. Technician will pulled the driver sill plate and inspect the wiring for damaged or corroded circuits. Technician will repair any damaged or corroded circuits.
PIT55322017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE. This Preliminary Information communication provides information to the technician about vehicles that have a squeak or chirp type noise from the rear of the vehicle. Technician should use the latest version of PI1201. If the noise is gone replace the muffler and tail pipe assembly.
10-00-89-005F2017-07-18. Service bulletin. EQUIPMENT; ENGINE. This informational bulletin provides warranty policy information on revised wiring repair labor operations and required additional information.
10-00-89-005F2017-07-18. Service bulletin. EQUIPMENT; ENGINE. This informational bulletin provides warranty policy information on revised wiring repair labor operations and required additional information.
16-NA-2222017-05-25. Service bulletin. ENGINE. THIS INFORMATIONAL BULLETIN PROVIDES THE TECHNICIAN WITH WHAT MAY HAPPEN TO AN ENGINE DUE TO LACK OF MAINTENANCE.
15-06-01-002D2017-05-25. Service bulletin. ENGINE AND ENGINE COOLING. THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPLACE THE VALVE LIFTER OIL MANIFOLD AND THE LIFTERS TO CORRECT THE CUSTOMERS CONCERN OF ENGINE MISFIRE, TICK NOISE AND MIL ON.
PIT5206E2017-05-22. Service bulletin. SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES; PARKING BRAKE; ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL; POWER TRAIN:AUTOMATIC TRANSMISSION; ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN WITH THE STEPS ON DIAGNOSING AND REPAIRING VEHICLES THAT MAY HAVE UNWANTED GRADE BRAKING, REDUCED ENGINE POWER WITH NO DRIVER INFORMATION CENTER MESSAGES “ BRAKE PEDAL OVERRIDE FEATURE “, TRANSMISSION BUSY OR FREQUENT SHIFTING UP OR DOWN, AND DIAGNOSTIC TROUBLE CODES P057B, P057C, AND/OR P057D MAY OR MAY NOT BE SET. TECHNICIAN WILL USE THIS PRELIMINARY INFORMATION TO FIND THE BRAKE PEDAL POSITION DATA PARAMETERS IN THE SCAN TOOL, AND ALSO TO PROVIDE SOME ADDITIONAL DIAGNOSTIC HELP. THESE ISSUES MAY BE CAUSED BY AN INCORRECT BRAKE PEDAL POSITION SENSOR INPUT TO THE ENGINE CONTROL MODULE. TECHNICIAN WILL VERIFY WITH THE SCAN TOOL IF THE ENGINE CONTROL MODULE HAS THE CORRECT PARAMETERS FOR THE BRAKE PEDAL POSITION SENSOR. IF AN ENGINE CONTROL MODULE BRAKE PEDAL POSITION SENSOR RELEARN IS PERFORMED, THE TRUCK MAY BE TEMPORARILY REPAIRED UNTIL THE INTERMITTENT WIRING ISSUE BETWEEN THE ENGINE CONTROL MODULE AND BRAKE PEDAL POSITION SENSOR OCCURS AGAIN. ON 2014 AND NEWER TRUCKS INSPECT AND REPAIR ANY DAMAGE TO X115 AND X119. ON THE 2014 AND PREVIOUS TRUCKS INSPECT AND REPAIR ANY DAMAGE TO X205.
PIP54272017-05-22. Service bulletin. ENGINE; ELECTRICAL SYSTEM. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLE THAT MAY HAVE A SERVICE ENGINE SOON MALFUNCTION INDICATOR LAMP ON. TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODES P2635, U0074 AND OR U18A2. TECHNICIAN WILL NEED TO FOLLOW PUBLISHED DIAGNOSTICS FOR DIAGNOSTIC TROUBLE CODES U0074 WOULD TAKE PRIORITY OVER U18A2 IF BOTH SET BEFORE ADDRESSING DTC P2635.
PIP54232017-05-19. Service bulletin. ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE A SERVICE ENGINE SOON MALFUNCTION INDICATOR LAMP ON. TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODES P0106 AND P0506. TECHNICIAN WILL INSPECT FOR A BROKEN VALVE SPRING AND REPLACE AS NEEDED.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.