WenmarOpen by Wenmar Pro

Service bulletins for the 2008 Chevrolet Tahoe

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

1399 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
PI08762018-05-29. Service bulletin. POWER TRAIN. This preliminary informational bulletin provides information on replacing the transmission fluid level indicator if a customers comments regarding one being broken.
01-00-89-010J2018-05-21. Service bulletin. ENGINE; SERVICE BRAKES; EQUIPMENT; POWER TRAIN:AUTOMATIC TRANSMISSION. This informational bulletin provides a revision for 01-00-89-010I to add the 2013 model year.
11-06-04-007C2018-05-21. Service bulletin. EQUIPMENT; ENGINE; ELECTRICAL SYSTEM; POWER TRAIN. This technical bulletin provides a procedure for replacing the throttle position sensor cover for concerns regarding a indicator lamp illuminated reduced power message displayed and DTC P2135 set.
PIP4112R2018-05-21. Service bulletin. EQUIPMENT; POWER TRAIN; ENGINE. This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
03-07-29-004J2018-05-21. Service bulletin. POWER TRAIN:MANUAL TRANSMISSION. This informational bulletin provides technicians with information to assist in identifying operating characteristics of manual transmissions that repair attempts will not change.
12-07-30-001D2018-05-21. Service bulletin. POWER TRAIN; ENGINE. This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all the information in relation to that part being returned.
02-07-30-029W2018-05-21. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN:AUTOMATIC TRANSMISSION. This informational bulletin provides information to the technician on what parts of an engine or transmission will require the PQC to be notified.
02-07-30-029V2018-05-21. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING; EQUIPMENT. This informational bulletin provides information to the technician on what parts of an engine or transmission will require the PQC to be notified.
PI0938A2018-05-21. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION. This preliminary bulletin provides information on what labor operation number to use for various electrical/electronic control issues.
01-07-30-042H2018-05-21. Service bulletin. POWER TRAIN:CLUTCH ASSEMBLY; POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER; POWER TRAIN. This information was created to inform the technician that the 2-3 upshift and the 3-2 downshift clunk is caused by the releasing of the 2-4 band and application of the 3-4 clutch assembly during an upshift. Also during a 3-2 downshift, the releasing of the 3-4 clutch during the application of the 2-4 band, can cause torque reversal down the output shaft creating a clunk. This is a normal condition.
080730035C2018-05-21. Service bulletin. POWER TRAIN. This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
09-07-30-001F2018-04-23. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This technical bulletin provides a revision for 09-07-30-001E to update the Correction and Warranty Information.
PI09382018-04-23. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. This preliminary information bulletin provides information on powertrain and various electronic/electrical control issues.
13-08-116-001A2018-04-23. Service bulletin. TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS; POWER TRAIN; ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This technical bulletin provides a procedure on aftermarket ALSL or DLC devices causing multiple issues due to suspected tampering.
09-06-04-026G2018-04-23. Service bulletin. ENGINE; POWER TRAIN. This informational bulletin provides information of suspected tampering or vehicle modifications for non-GM (Aftermarket) engine and transmission calibrations for V6 and V8 gasoline engines Using Tech 2® or global diagnostic system 2 (GDS 2)
PI0522D2018-04-23. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This preliminary information bulletin provides a procedure to adjust the transmission dipstick tube and/or install the transmission fluid filler tube sleeve to eliminate a tick, buzz or rattle noise from the front of dash, transmission filler tuber cracked or broken.
12-07-30-001B2018-04-16. Service bulletin. POWER TRAIN. This informational bulletin provides information for service agents not required to contact product quality center for CNG, LPG or gasoline engine, transmission and/or transfer case.
PIP5168F2018-02-21. Service bulletin. POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT; BACK OVER PREVENTION; FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published “Engine Cranks But Does Not Run” diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly.
06-00-89-031C2017-12-22. Service bulletin. POWER TRAIN; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This informational bulletin provides information to dealership personnel on proper engine and automatic transmission/transaxle identification.
030729004I2017-12-22. Service bulletin. POWER TRAIN. This informational bulletin was created for the Manual Transmission Operating Characteristics. The different noises caused by driver habit, weather conditions , and normal manual transmission noises.
1203100022017-12-22. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER. This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles
PIP4112P2017-12-22. Service bulletin. ENGINE; POWER TRAIN. This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
PIP4653E2017-12-22. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicle that have a Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0601, P0603, P0604, P062F or P1621 stored in the Transmission Control Module. Technician will need to ensure that the Diagnostic Trouble Codes are set in the Transmission Control Module. If the Diagnostic Trouble Codes are only set in the Transmission Control Module reprogram the Transmission Control Module.
09-07-30-018C2017-10-12. Service bulletin. POWER TRAIN; POWER TRAIN:AUTOMATIC TRANSMISSION. This warranty administration bulletin provides information on the change in automatic transmission add conditions documentation and claim submissions
PIP4101B2017-08-15. Service bulletin. POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE). This Preliminary Information communication provides information to the technician about vehicles that have a Service 4WD light on and the system inoperative. Technician may find Diagnostic Trouble Code B2725 set. Technician will need to replace the transfer case dash switch.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.