P0513 on the 2016 Chevrolet Suburban
The bulletins listed name this code in NHTSA's summary, or are about the same components. A bulletin or a recall listed here may apply to the model year. None of it is a diagnosis.
Nobody has written a description of this code yet.
| PIT5391F | 2023-03-13. Service bulletin. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be on when the ignition is in the run position. Technician may find Diagnostic Trouble Codes P0513 and or P262B may also be set. Technician will pulled the driver sill plate and inspect the wiring for damaged or corroded circuits. Technician will repair any damaged or corroded circuits. |
|---|---|
| PIT5391E | 2019-03-11. Service bulletin. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be on when the ignition is in the run position. Technician may find Diagnostic Trouble Codes P0513 and or P262B may also be set. Technician will pulled the driver sill plate and inspect the wiring for damaged or corroded circuits. Technician will repair any damaged or corroded circuits. |
| PIT5391D | 2018-05-21. Service bulletin. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be on when the ignition is in the run position. Technician may find Diagnostic Trouble Codes P0513 and or P262B may also be set. Technician will pulled the driver sill plate and inspect the wiring for damaged or corroded circuits. Technician will repair any damaged or corroded circuits. |
| PIT5391A | 2017-08-15. Service bulletin. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be on when the ignition is in the run position, Any of the following Diagnostic Trouble Codes may be set: B1370, B1325, P0650, P263A, P263B, P0513, and/or P0262B. Trucks equipped with 4WD may have a Service 4WD message and Diagnostic Trouble Codes C0364 and/or U0403 may set. Also the sound of a relay clicking while driving or engine stays running with ignition off until door is opened. Technician will inspect all the under-hood fuse block-X50A connectors for any backed out terminals, poor terminal fit and/or bent/twisted terminals. The most common terminals with these issues have been with terminal M5 at connector X4, for circuit 5199 and terminal M7 at connector X2, for circuit 439. Technician will inspect for any backed out terminals, poor terminal fit and/or bent/twisted terminals at the left instrument panel fuse block - X51L. The most common terminals with these issues have been terminal 42 at connector X1, for circuit 5199 and terminal 44 at connector X2, for circuit 1850. Also circuit 5199 will need to be inspected and repaired under the driver?s sill plate. |
| PIT5405C | 2017-08-15. Service bulletin. This Preliminary Information communication provides information to the technician about vehicles that have a reduced or loss of power steering assist, steering wheel jerks or kicks back when turning, Service Stabilitrak message with warning chime, engine stall, Instrument Panel Cluster going blank or inoperative, radio/Integrated Center Stack going blank, Heater-Vent-Air Conditioning going blank, hood ajar message and/or dome lamps flash when shifting into reverse, alarm sounds when locking doors or door locks cycling, and or wipers continue to run for a short time after turning off and then stop/park in the incorrect location. Technician may find Diagnostic Trouble Codes U0073, U0078, U0029, U0028, U0415, U0140, U0126, U0121, U0101, U0100, C0544, C0710, U1510, B127B, B2605, B3600, C0800, U0428, U0452, U0131, and P0513 set in the vehicle. Check the body control module ground at the G218 location. The front dash insulator mat may be trapped between the ground eyelet and the body stud. Remove the round nut and eyelet and cut the front dash insulator mat away from the ground stud so it no longer interferes with the ground stud and reinstall the eyelet and ground nut. Technician will also inspect the starter solenoid battery cable for shorting out on the starter heat shield. Technician will need to voltage drop the battery cables. The battery should be tested using the GR8. X183 or X133 should be inspected for any broken/loose/backed out terminals. |
| PIT5391C | 2017-08-15. Service bulletin. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be on when the ignition is in the run position. Technician may find Diagnostic Trouble Codes P0513 and or P262B may also be set. Technician will pulled the driver sill plate and inspect the wiring for damaged or corroded circuits. Technician will repair any damaged or corroded circuits. |
| PIT5391B | 2016-10-21. Service bulletin. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON HOW TO DIAGNOSE AND REPAIR VEHICLES THAT HAVE A NO CRANK OR A START AND THEN IMMEDIATE STALL, SERVICE ENGINE SOON MALFUNCTION INDICATOR LAMP MAY NOT BE ON WHEN THE IGNITION IS IN THE RUN POSITION. TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODES P0513 AND OR P262B MAY ALSO BE SET. TECHNICIAN WILL PULLED THE DRIVER SILL PLATE AND INSPECT THE WIRING FOR DAMAGED OR CORRODED CIRCUITS. TECHNICIAN WILL REPAIR ANY DAMAGED OR CORRODED CIRCUITS. |
7 on file from NHTSA, as of 2026-10-19. See them in the bulletin list. A bulletin lists model years: read the document for which vehicles it concerns.