Service bulletins for the 2009 Chevrolet Suburban
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1388 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Engine are shown. Show all
| PIP4792D | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING; FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician about vehicles that have a an extended crank on cold start, brief rough running on cold start, black exhaust color, and/or Service Engine Soon Malfunction Indicator Lamp on. Technician may find a Diagnostic Trouble Code P0172 and or P0175. Technician will need to check the Fuel Alcohol Content parameter found in the Fuel Trim Data List of the scan tool and the measured ethanol content of a fuel sample using the J44175 tester. If the difference is 17% or greater, reprogram the Engine Control Module with the latest calibrations from TIS2web. |
|---|---|
| PIP5168A | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published "Engine Cranks But Does Not Run" diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. |
| PIP5089A | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code C0569 that will not clear. Technician should be advised if there are any issues with the rotational position sensor, incremental position sensor, encoder motor, motor A or B circuits, rotational position sensor or incremental position sensor circuits when the transfer case control module attempts to determine location the location cannot be determined correctly. |
| PIP4568Q | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER. This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed. |
| PIP5169 | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that are setting Diagnostic Trouble Code P0300 after engine repairs. Technician will need to ensure that injector connectors for cylinder 5-7 and 6-8 are not crossed. |
| PIP5168 | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published ?Engine Cranks But Does Not Run? diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. |
| PIP5168B | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published ?Engine Cranks But Does Not Run? diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. |
| PIP5104A | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that may have a cold engine tick noise for 50 seconds at start up. Technician determines if the tick noise is possibly coming from the exhaust manifold, as this noise could easily be mistaken for an engine tick noise. If your SI diagnosis does not isolate the cause of this concern, this concern should be considered a vehicle design characteristic of the ECM calibration and no additional repairs should be performed. |
| PIP3343D | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Technician will need to clean the area of the oil leak, clean and dry the PCV hoses, and replace the oil fill cap with part number 12589430. |
| PIP5168C | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE); ENGINE. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published ?Engine Cranks But Does Not Run? diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. |
| PIP4138P | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter. |
| PIP4828C | 2017-08-15. Service bulletin. POWER TRAIN; ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a rough idle and/or momentary lack of power after cold starting the engine and immediately placing the transmission in gear. Technician should follow published Service Information diagnostics first. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. |
| PIP5029G | 2017-05-16. Service bulletin. ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A MALFUNCTION INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. TECHNICIAN WILL NEED TO PERFORM PUBLISHED SERVICE INFORMATION DIAGNOSTICS. IF TECHNICIAN FINDS CARBON, AN UPPER ENGINE AND VALVE CLEANING SHOULD BE PERFORMED. |
| PIP-5258 | 2017-04-11. Service bulletin. ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE SERVICE ENGINE SOON AND A DIAGNOSTIC TROUBLE CODE P0011. IF THE TECHNICIAN HAS FOLLOWED SERVICE INFORMATION DIAGNOSTIC TROUBLE CODE FOR P0011AND THE ROOT CAUSE WAS NOT FOUND THE OIL PRESSURE AT THE OIL PRESSURE SENDER SHOULD BE CHECKED. ALSO THE NUMBER 2 CAM BEARING SHOULD BE INSPECTED. |
| 10-06-01-008K | 2017-03-20. Service bulletin. ENGINE. THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CORRECT THE CUSTOMERS CONCERN TO REPLACE THE LEFT SIDE VALVE COVER AND ACTIVE FUEL MANAGEMENT OIL DEFLECTOR TO REDUCE OIL CONSUMPTION. |
| PIP5104B | 2017-03-20. Service bulletin. ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE A COLD ENGINE TICK NOISE FOR 50 SECONDS AT START UP. TECHNICIAN DETERMINES IF THE TICK NOISE IS POSSIBLY COMING FROM THE EXHAUST MANIFOLD, AS THIS NOISE COULD EASILY BE MISTAKEN FOR AN ENGINE TICK NOISE. IF YOUR SI DIAGNOSIS DOES NOT ISOLATE THE CAUSE OF THIS CONCERN, THIS CONCERN SHOULD BE CONSIDERED A VEHICLE DESIGN CHARACTERISTIC OF THE ECM CALIBRATION AND NO ADDITIONAL REPAIRS SHOULD BE PERFORMED. |
| PIP4568R | 2017-03-14. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; ENGINE; EQUIPMENT ADAPTIVE/MOBILITY. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT SOME VEHICLES MAY HAVE A SERVICE ENGINE SOON LAMP, ENGINE MISFIRE ON CYLINDER 1, 4, 6, OR 7 AND/OR TICK NOISE. TECHNICIAN WILL FOLLOW SERVICE INFORMATION DIAGNOSIS FIRST. IF SERVICE INFORMATION DIAGNOSIS DOES NOT ISOLATE THE CAUSE OF THIS CONCERN PERFORM A CYLINDER DEACTIVATION ACTIVE FUEL MANAGEMENT SYSTEM COMPRESSION TEST IN SERVICE INFORMATION. IF THE RUNNING COMPRESSION OF THE MISFIRING CYLINDER STAYS BELOW 25 POUNDS PER SQUARE INCH REGARDLESS OF THE ACTIVE FUEL MANAGEMENT SOLENOID BEING COMMANDED ON OR OFF, AN ACTIVE FUEL MANAGEMENT LIFTER IS MECHANICALLY COLLAPSED/STUCK OR UNLOCKING AS SOON AS THE ENGINE IS STARTED. REPLACE ALL ACTIVE FUEL MANAGEMENT LIFTERS, AND ALL PLASTIC LIFTER GUIDES. ALSO PERFORM THE CYLINDER DEACTIVATION ACTIVE FUEL MANAGEMENT VALVE LIFTER OIL MANIFOLD DIAGNOSIS AND TESTING IN SERVICE INFORMATION. IF IT ISOLATES A CONCERN WITH THE VALVE LIFTER OIL MANIFOLD, REPLACE IT AND REEVALUATE THE CONCERN. THE ACTIVE FUEL MANAGEMENT LIFTERS CAN ALSO BE MONITORED FOR PROPER OPERATION BY CAREFULLY INSPECTING THE CYLINDER 1, 4, 6, AND 7 ROCKERS AND VALVES WHILE CRANKING OR BRIEFLY AND SAFELY RUNNING THE ENGINE WITH THE VALVE COVERS REMOVED. IF THE VALVE OR VALVES OF AN ACTIVE FUEL MANAGEMENT CYLINDER STOP MOVING WHILE DOING THIS TEST, THE ACTIVE FUEL MANAGEMENT LIFTER IS CAUSING THE CONCERN. FOR 2008-2009 FULL SIZE TRUCK/SUV OR A 2007-2009 CHEVROLET TAHOE WITH THE POLICE PACKAGE REPROGRAM THE ENGINE CONTROL MODULE. ON THE 2008-2009 PONTIAC G8, 2010-2011 CAMARO, AND 2007-2010 FULL SIZE TRUCKS WITH ACTIVE FUEL MANAGEMENT, ALSO DETERMINE IF THE ACTIVE FUEL MANAGEMENT PRESSURE RELIEF VALVE SHIELD THAT IS LISTED IN THE LATEST VERSION OF 10-06-01-008 HAS EVER BEEN INSTALLED. ON PASSENGER CARS WITH THE LS4 ENGINE, DETERMINE IF THE UPDATED OIL PAN GASKET THAT IS LISTED IN THE LATEST VERSION OF 11-06-01-007 HAS BEEN INSTALLED. |
| PIP4786C | 2016-10-20. Service bulletin. ENGINE AND ENGINE COOLING. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE LOW OIL PRESSURE MESSAGE. TECHNICIAN MAY ALSO FIND A DIAGNOSTIC TROUBLE CODE P0521 IN THE ENGINE CONTROL MODULE. TECHNICIAN SHOULD FOLLOW ALL PUBLISHED SERVICE INFORMATION DIAGNOSIS. WHEN USING A SCAN TOOL IF THE OIL PRESSURE IS LOW BUT THE OIL PRESSURE AT THE OIL FILTER HOUSING IS CORRECT, TECHNICIAN SHOULD INSPECT THE VALVE LIFTER OIL FILTER FOR DEBRIS/SLUDGE THAT COULD BE RESTRICTING OIL FLOW TO THE OIL PRESSURE SENSOR. TECHNICIAN SHOULD REMOVE THE VALVE LIFTER OIL FILTER AND CLEAN IT. IF THE VALVE LIFTER OIL FILTER CANNOT BE CLEANED REPLACE IT. |
| PI1394A | 2016-10-19. Service bulletin. ENGINE. THIS INFORMATIONAL BULLETIN PROVIDES ADDITIONAL INFORMATION ON HOW TO INSTALL PISTONS AND SUGGEST WHAT TOOLS TO USE. |
| 030604017I | 2016-10-18. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL. THIS INFORMATIONAL BULLETIN EXPLAINS THE USE OF DIESEL FUEL ADDITIVES IN AN ENGINE, ARE NOT REQUIRED UNLESS THE CUSTOMER DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS. |
| 030603004R | 2016-10-18. Service bulletin. ENGINE; ELECTRICAL SYSTEM:12V/24V/48V BATTERY. THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON HOW TO TEST A BATTERY AND WHAT IS NEEDED TO WARRANTY A BATTERY. |
| 000601026I | 2016-10-18. Service bulletin. ENGINE. THIS INFORMATIONAL BULLETINS PROVIDES INFORMATION ON THE INTAKE MANIFOLD INSPECTION/REPLACEMENT AFTER SERVERE INTERNAL ENGINE DAMAGE. |
| 000601012F | 2016-10-18. Service bulletin. ENGINE. THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE GASKET SEALING SURFACES. |
| SB-07-06-01-016C | 2016-08-09. Service bulletin. ENGINE. THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION INTERNAL ENGINE NOISE OR DAMAGE AFTER OIL FILTER REPLACEMENT |
| SB-06-06-05-001G | 2016-08-05. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON CHANGES IN EXHAUST TONE FOR ACTIVE FUEL MANAGEMENT ENGINES WHEN IN THREE OR FOUR CYLINDER MODE. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.