WenmarOpen by Wenmar Pro

Service bulletins for the 2016 Chevrolet Silverado

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

2286 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
PIP5213D2017-08-15. Service bulletin. POWER TRAIN. This Preliminary Information communication advises the technician that the part restriction on the 8L45/8L90 8 speed and the LCT1000 6 Speed Allison automatic transmission has ended.
PIT5438A2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a click, rattle or a squeak nose coming from the dash. Technician will use Service Information to locate the Accessory AC and DC Power Control Module located to the right of the steering column. Remove the power inverter module and apply two sided tape to the module bracket to insulate it from the mount. The instrument panel accessory bezel will also need to be removed. Apply flocking tape to the instrument panel accessory bezel retainers. Also the instrument panel extension will need to be removed. Apply foam tape around connectors located under grill to prevent them from rattling on grill. Apply flocking tape to the instrument panel extension retainers and apply a strip of foam tape along the edge of the grill to isolate the grill from the dash.
PIP53372017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; POWER TRAIN:AUTOMATIC TRANSMISSION. This Preliminary Information communication provides information to the technician on the step to diagnose and repair the vehicles that may have a shake or shudder during light throttle acceleration, between 30 and 65 mph steady state driving. Also shudder feeling that may be described as driving over rumble strips or rough pavement. Technician will drive the vehicle and monitor the torque converter clutch slip. The torque converter clutch slip speed should be 10 rpm or less also note if the shudder takes place during torque converter clutch apply. If the torque converter clutch slip speed is in the range of 10 RPM or less the condition is possibly related to engine performance. If the shudder is only present in 4 cylinder mode and torque converter clutch slip is 10 rpm or less deem the shudder concern normal characteristic of Active Fuel Management. If the slip speed is beyond 10 rpm or there is shudder during torque converter clutch apply the torque converter will need to be replaced with a updated part number.
PIP5199A2017-08-15. Service bulletin. ENGINE; EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician about vehicles with a crankshaft balancer appears to be out of balance or wobbling while watching it with the engine running. Technician will need to check crankshaft balancer run out. If the balancer run out is greater than 0.25mm the crankshaft balancer will need to be replaced.
PIP53352017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Codes P0340 and P0341 setting at times. Technician should use normal published Service Information diagnostics. If normal Service Information diagnostics does not isolate the concern, inspect for corrosion in connector X154 located on the front cover next to the vacuum pump.
PIT5202C2017-08-15. Service bulletin. ENGINE; POWER TRAIN; SERVICE BRAKES, HYDRAULIC:POWER ASSIST. This Preliminary Information communication provides information to the technician about vehicles that are equipped with 6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option Code (M5U) Automatic Transmission. Starting with the 2013 model year, Full Size Trucks and Utilities now have Powertrain Grade Braking. Powertrain grade braking assists when driving on a downhill grade to help maintain desired vehicle speed by using the engine and transmission to slow the vehicle.
PIP4404F2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician vehicles with a slight rough idle. Technician should compare the concern with a like vehicle. If the concern is worse than a like vehicle, technician should follow published Service Information diagnosis and repair as necessary.
PIP3504D2017-08-15. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE; FUEL SYSTEM, DIESEL. This Preliminary Information communication provides information to the technician about vehicles that have a hard start when the engine is hot. If the fuel found in the vehicle has an American Petroleum Institute specific gravity reading of 39 - 44, and the fuel sample you used for comparison has an American Petroleum Institute specific gravity reading of 30 - 39, drain the fuel system and refill with a known good diesel fuel and retest.
PIT55302017-08-15. Service bulletin. WHEELS; EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician about removing the tinnerman push nuts when installing the accessory 22" 6-Spoke Split Chrome Wheels Regular Production Option Code (SEU) or during any service requiring wheel removal.
PIT5519B2017-08-15. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. This Preliminary Information communication provides information to the technician about vehicles that have a poor Heater-Vent-Air Conditioning air flow from the passenger side far right dash vent when compared to the other dash vents. Technician will need to remove the Heater-Vent-Air Conditioning air distributor duct. Technician can now cut out the portion of the deflector to increase air flow.
PIT5341B2017-08-15. Service bulletin. LATCHES/LOCKS/LINKAGES:DOORS:LATCH. This Preliminary Information communication provides information to the technician about owners that want the auto door lock disabled. There is no avalible setting or Body Control Module calibration to turn off the auto door locks.
PIT5438C2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a click, rattle or a squeak nose coming from the dash. Technician will use Service Information to locate the Accessory AC and DC Power Control Module located to the right of the steering column. Remove the power inverter module and apply two sided tape to the module bracket to insulate it from the mount. The instrument panel accessory bezel will also need to be removed. Apply flocking tape to the instrument panel accessory bezel retainers. Also the instrument panel extension will need to be removed. Apply foam tape around connectors located under grill to prevent them from rattling on grill. Apply flocking tape to the instrument panel extension retainers and apply a strip of foam tape along the edge of the grill to isolate the grill from the dash.
PIT5517A2017-08-15. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communicates New model features of the 2016 and 2017 Silverado and Sierra eAssist.
PIC6216B2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles voice recognition inoperative for calling Bluetooth phone contacts. Technician will need to Clear All Private Data and re-pair any phones that were deleted.
PIP54462017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This Preliminary Information communication provides information to the technician about vehicles that have a Harsh Shift 1/2 and 2/3 and Sputter Applying Throttle Between 0 and 30%, Rough idle. Technician may find Diagnostic Trouble Codes P0101, P0171, P0172, P0174, and or P0175. Technician should inspect for cast flashing near the Mass Air Flow sensor as seen below.
PIT5288E2017-08-15. Service bulletin. ELECTRONIC STABILITY CONTROL (ESC); VISIBILITY; STEERING; TIRES; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that may have any of these concerns remote keyless entry, passive Entry and Start Inoperative, No Fob detect message on driver information center, service tire pressure system, no audio, touch screen Inoperative, Steering Wheel Controls Inoperative, Service Stabilitrak, rear power windows inoperative, rear wiper inoperative, and or a dead battery. Technician may find Diagnostic Trouble Codes B3101, B144C, C0710, C0544, U1548, U1549, U154A, U0151, U0126, U0415, U0077, U0028 and/or U0029. Technician should inspect the left instrument panel for the wire harness being pinched. Technician will need to repair the wire harness and reroute the wire harness.
PIT5354A2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL. This Preliminary Information communication advises the technician how determine if the vehicle is equipped with wireless fidelity. Technician should check the Regular Production Option Code list for (VV4).
PIT3099N2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
PIT5434A2017-08-15. Service bulletin. ELECTRICAL SYSTEM; SEATS. This Preliminary Information communication provides information to the technician only to provide additional tips when diagnosing a front heated seat concern and is not meant to be a diagnostic flow chart or replace Service Information. Always, perform and refer to Service Information for the latest diagnostic information and procedures. Trucks equipped with heated and cooled seats Regular Production Option Code (KB6), may comment on any of the following front heated seat concerns. Condition 1, a front heated seat (back and/or cushion) is inoperative. Technician should diagnosis each affected seat heater individually. Technician should test all four circuits Power, Ground, Control (from Body Control Module) and Heating Element Supply Power. The Power, Ground, Control (from Body Control Module) can easily be checked by starting the engine and turn on the cooled seat. When the cooled seats are turned on the blower in each seat back and cushion will turn on at that point technician will be able to hear the blower moving. The heating element supply power circuit can be test by disconnecting the affected heating element and connect a voltmeter across the heating element supply power and ground circuit. Then start the engine and turn on the heated seat, the blower will supply system voltage on the element supply power circuit for 1 to 2 seconds. With the heated seat element disconnected, use an ohmmeter to measure the resistance of the heating element. If all of the above steps check ok or the heating element resistance is close to the approximate spec, reconnect all disconnected connectors. Connect a voltmeter across the affected heated seat element connectors supply power and ground circuits back probing the connector. Then check the resistance of the heating element. The resistance should be close to the same resistance as when testing with the connector unplugged. Now check the voltage with the engine running and the heated sets on high. Condition 2, the front heate
PIT55292017-08-15. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL. This Preliminary Information communication provides information to the technician about vehicles that have Trailer connection not recognized or ?Check Trailer wiring? or ?Service Trailer Brake? message. Technician may find Diagnostic Trouble Codes C1112, C1113, C1114, C111B, U1556, and/or U1505. Technician will need to inspect the Trailer Brake Power Module connector for corroded terminals and replace as necessary.
PIP5337G2017-08-15. Service bulletin. POWER TRAIN; VEHICLE SPEED CONTROL:LINKAGES; SERVICE BRAKES. This Preliminary Information communication provides information to the technician on the step to diagnose and repair the vehicles that may have a shake or shudder during light throttle acceleration, between 30 and 65 miles per hour steady state driving. Also shudder feeling that may be described as driving over rumble strips or rough pavement. Technician will need to run the vehicle in three different operational modes. The three modes are Normal, torque converter clutch open, and torque converter clutch closed. Technician will need to press and hold the tow-haul mode button for five seconds to disable grade braking to prevent downshifts during test. Technician will need to duplicate the concern in Normal mode. If the concern is gone in torque converter clutch open and closed then the torque converter should be replaced. If the concern is not present in normal mode, torque converter clutch open, and torque converter clutch closed the concern is not with the shudder. Technician should use of the PICO scope and Noise, Vibration and Harshness software can be used to confirm torque converter clutch shudder, Engine, Tire or Driveline component related conditions. Flush the cooler lines and cooler using DT-45096 transmission oil cooling system flush and flow test tool when the torque converter is replace.
PIT5501D2017-08-15. Service bulletin. STEERING; STEERING:GEAR BOX:SHAFT PITMAN. This Preliminary Information communication provides information to the technician on the steps to diagnosis and repair steering that feels loose or has excessive play. This concern could be caused by the Pitman Shaft Over-Center Preload Adjustment becoming misadjusted. Technician will need to replace the steering gear pitman arm shaft with an updated design.
PIP5163B2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; FUEL SYSTEM, GASOLINE; ENGINE. This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIP5437A2017-08-15. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that have harsh concerns. Technician are advised to use GDS2 software to confirm which shift is causing the concern. On low mileage vehicles technician are instructed to perform a drive learn procedure. On higher mileage vehicles technicians are instructed to remove the transmission fluid pan and inspect for debris. If debris is found technicians should disassemble and inspect for root cause of the concern and repair the transmission as needed. If no debris is found technicians are advised to replace the valve body.
PIP54422017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have an exhaust leak, noisy exhaust, or noise mid-vehicle. Technician will need to check for an unseated pipe to pipe mid-joint connection. Technician will need to install new exhaust band.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.