WenmarOpen by Wenmar Pro

Service bulletins for the 2015 Chevrolet Silverado

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

3099 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Fuel system are shown. Show all

Bulletins, newest first
PIP51982017-12-22. Service bulletin. ENGINE AND ENGINE COOLING; FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician about vehicles that may have Service messages in the Driver Information Center, Malfunction Indicator Lamp on, Erratic fluctuating engine oil pressure gauge, engine crank no start, and engine may run rough or misfire. Technician may find Diagnostic Trouble Codes. Technician should use published Service Information diagnostics for the Diagnostic Trouble Codes that are set. If the diagnosis does not lead to a resolution check for chafing of the engine wiring harness that is routed near the Exhaust Gas Recirculation Valve. Technician should repair any damaged wiring and fully seat the wire retaining harness. Also the technician should bend the Exhaust Gas Recirculation Valve gasket over to prevent a re-occurrence.
PIP5151B2017-12-22. Service bulletin. FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that may have a hard start, no start, rough running, or low fuel pressure. Technician may find Diagnostic Trouble Codes P0087, P0088, P0191 and P128E during the inspection. If during the inspection of the fuel system contamination is found the complete fuel system will need to be cleaned and flushed. After the fuel system is cleaned out test the fuel using the latest version of PIT3173.
PIP4379M2017-12-22. Service bulletin. POWER TRAIN; FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician about vehicles that have not engagement into drive, delayed, no engagement into reverse, and or a range inhibit. Technician may find Diagnostic Trouble Codes P0701, P0731, P0732, P0733, P0734, P0736, P0751, P0756, P0761, P0776, P0843, P0848, P0873, P0877, P0894 or P2723. Technician should follow published Service Information diagnostics for Diagnostic Trouble Code P0701 first. Technician will also ensure the fluid level is at the top of the hot band when the transmission fluid temperature is 175° Fahrenheit. Diagnostic Trouble Codes P0701, P0731, P0732, P0733, P0734, P0736, P0751, P0756, P0761, P0776, P0843, P0848, P0873, P0877, P0894 or P2723 can set by the following fluid service/filter change, transmission service involving removing the pan, low fluid level caused by leaks, or after long periods of storage. If the fluid level has been properly checked using the HOT check procedure listed in Service Information document 2408059 and any of the Diagnostic Trouble Codes reset during a cold start inspect the internal suction filter for possible cracks. If no other concerns are found inspect for a stuck lube regulator valve in the pump cover due to debris.
PIP52042017-12-22. Service bulletin. FUEL SYSTEM, DIESEL. This Preliminary Information communication advises the technician that the Diesel Oxidation Converter part numbers 15231895, 22768282, 22770967, 22887212, 22893734 and 22977171 will be placed on a parts restriction through the General Motors Product Quality Center. Dealer will need to contact General Motors Product Quality Center for further assistance.
PIT5161F2017-11-14. Service bulletin. FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. The bump clunk issue may be due to fuel movement in the fuel tank when not completely full. The condition is eliminated after completely filling the fuel tank.
PIP5411F2017-11-14. Service bulletin. FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that may have hesitation or a stalling condition while in ambient temperatures 100 degrees or higher. Technician may find Diagnostic Trouble Codes P2635 and or P018B set. The dealer is advised to replace the in tank fuel pump module assembly to correct the condition.
05-00-89-072D2017-10-15. Service bulletin. FUEL SYSTEM, GASOLINE. This informational Bulletin provides Do's and Don'ts for maximizing gasoline engine fuel economy, other various tips and a list of websites for additional information.
16-NA-1022017-08-31. Service bulletin. FUEL SYSTEM, GASOLINE. This technical bulletin provides a procedure to clean and repair the complete fuel system due to dirt getting into the fuel system causing the vehicle to have a hard or no start.
PIT5161C2017-08-15. Service bulletin. FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY; FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. The bump clunk issue may be due to fuel movement in the fuel tank when not completely full. The condition is eliminated after completely filling the fuel tank.
PIP53392017-08-15. Service bulletin. FUEL SYSTEM, OTHER. This Preliminary Information communication provides information to the technician about a customer?s request to remove or disable the Bi-Fuel Compressed Natural Gas system. General Motors does not condone the removal of the original equipped Compressed Natural Gas systems.
PIP4864P2017-08-15. Service bulletin. FUEL SYSTEM, DIESEL:STORAGE:TANK ASSEMBLY; FUEL SYSTEM, DIESEL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that may have "Exhaust Fluid Low", "Exhaust Fluid Empty - Refill Now", "Exhaust Fluid Range: XXX" or "Service Exhaust Fluid - See Owners Now" on the Driver Information Center. If the technician is working on 2010 and 2011 model years campaign 11001 has now been released. Other vehicles technician will need to check the Body Control Module and the scan tool to insure the latest calibration are installed in both. Then use the scan tool to check Reductant System Data in the Engine Control Module. Ensure that all three diesel exhaust fluid level sensors are active with the diesel exhaust fluid tank level showing 100%. If the tank level is below 100% add up to 2 gallons of diesel exhaust fluid. After adding the fluid, use a scan tool to reset the reductant fluid tank level. When the reductant level warning shows "none" the diesel exhaust fluid system reset and reprogram is complete.
PIP4949E2017-08-15. Service bulletin. FUEL SYSTEM, OTHER:DELIVERY:FUEL PUMP; FUEL SYSTEM, OTHER:FUEL INJECTION SYSTEM; FUEL SYSTEM, OTHER:FUEL FILTER. This Preliminary Information communication provides information to the technician about vehicles that have a hard start or a no start. Technician may find Diagnostic Trouble Code DTCs P0087, P0088, P0191 or P128E. Technician will need to follow all Service Information diagnose for the Diagnostic Trouble Code. If the current Service Information diagnostic has led to Fuel Injection Pump replacement, Fuel Pressure Regulator 1 must be inspected for magnetic metal debris. If there is a questionable amount of magnetic debris found on Pressure Regulator 1 remove the Fuel Rail Pressure Sensor and/or Fuel Pressure Regulator 2 to inspect for magnetic metal debris. If technician will need to replace all of the parts listed under the latest version of PIP4949 found in the Service Forms section of Global Connect if debris is found. Clean and flush all fuel chassis lines, filter pipes, and other engine mounted fuel system pipes not replaced. Also the fuel filter housing must be cleaned with a new fuel filter installed. Then the fuel tank and fuel sender must be cleaned and flushed.
PIT4943D2017-08-15. Service bulletin. FUEL SYSTEM, GASOLINE; FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
PIP5234A2017-08-15. Service bulletin. FUEL SYSTEM, OTHER:FUEL INJECTION SYSTEM. This Preliminary Information communication advises the technician when Service Information diagnostics indicates a fuel injector may need to be removed for a repair or replaced the injector will need a new seal. This Preliminary Information contains all the O-ring seal and the injector kit part numbers.
PIP5179B2017-08-15. Service bulletin. ENGINE; EQUIPMENT:MECHANICAL; FUEL SYSTEM, OTHER:FUEL INJECTION SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have extended or long crank time during cold ambient air temperatures. Direct Injection systems run at higher pressures, and the mechanical pump on the engine must build up the required pressure before the first injection event occurs. Direct Injection engines may have slightly longer cold crank times than that of port fuel engines.
PIP3504D2017-08-15. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE; FUEL SYSTEM, DIESEL. This Preliminary Information communication provides information to the technician about vehicles that have a hard start when the engine is hot. If the fuel found in the vehicle has an American Petroleum Institute specific gravity reading of 39 - 44, and the fuel sample you used for comparison has an American Petroleum Institute specific gravity reading of 30 - 39, drain the fuel system and refill with a known good diesel fuel and retest.
PIP5163B2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; FUEL SYSTEM, GASOLINE; ENGINE. This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIP5204D2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL; FUEL SYSTEM, DIESEL. This Preliminary Information communication advises the technician that the Diesel Oxidation Converter part numbers 15231895, 22768282, 22770967, 22887212, 22893734 and 22977171 will be placed on a parts restriction through the General Motors Product Quality Center. Dealer will need to contact the General Motors Product Quality Center for further assistance.
PIP5133C2017-08-15. Service bulletin. FUEL SYSTEM, OTHER:DELIVERY:FUEL PUMP; FUEL SYSTEM, OTHER:FUEL INJECTION SYSTEM. This Preliminary Information communication advises the technician that the 6.6L Duramax Diesel Engine Fuel Injection Pump Part numbers 12645102, 12658095 and 12661059 will be placed on a parts restriction through the General Motors Product Quality Center. Dealer will need to contact General Motors Product Quality Center for further assistance.
PIP52342017-08-15. Service bulletin. FUEL SYSTEM, GASOLINE; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS. This Preliminary Information communication advises the technician when Service Information diagnostics indicates a fuel injector may need to be removed for a repair or replaced the injector will need a new seal. This Preliminary Information contains all the O-ring seal and the injector kit part numbers.
PIP5179A2017-08-15. Service bulletin. FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM; ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have extended or long crank time during cold ambient air temperatures. Direct Injection systems run at higher pressures, and the mechanical pump on the engine must build up the required pressure before the first injection event occurs. Direct Injection engines may have slightly longer cold crank times than that of port fuel engines.
PIP5279A2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:FUEL RAIL. This Preliminary Information communication provides information to the technician about vehicles that may have Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Codes P0089, P127C, P127D, P0192, P0193, P228C, P228D, and P006C. Technician should follow published Service Information diagnostics for the Diagnostic Trouble Codes that are stored. If Service Information does not lead to a repair for the concern, the fuel rail pressure sensor should be replaced.
PIP4786A2017-08-15. Service bulletin. FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY:PRESSURE RELIEF DEVICES. This Preliminary Information communication provides information to the technician about vehicles that may have low oil pressure message. Technician may also find a Diagnostic Trouble Code P0521 in the Engine Control Module. Technician should follow all published Service Information diagnosis. When using a scan tool if the oil pressure is low but the oil pressure at the oil filter housing is correct, technician should inspect the Valve Lifter Oil Filter for debris/sludge that could be restricting oil flow to the oil pressure sensor. Technician should remove the Valve Lifter Oil Filter and clean it. If the Valve Lifter Oil Filter cannot be cleaned replace it.
PIP52722017-08-15. Service bulletin. FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY:PRESSURE RELIEF DEVICES. This Preliminary Information communication provides information to the technician about vehicles that may have low oil pressure after an oil change. Technician will inspect the oil filter part number PF63E. Part number PF48 oil filter will fit but will cause a low oil pressure concern.
PIT53612017-08-15. Service bulletin. FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP. This Preliminary Information communication provides information to the technician about vehicles that may have a hard brake pedal or that increased effort is needed to depress the brake pedal. During the inspection the technician may find engine oil in the vacuum pump. If engine oil is found these parts should be placed the vacuum pump, vacuum Line between the booster and the pump, brake booster, and the master cylinder.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.