WenmarOpen by Wenmar Pro

Service bulletins for the 2015 Chevrolet Silverado

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

3099 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Backup camera are shown. Show all

Bulletins, newest first
PI1126G2018-05-21. Service bulletin. EQUIPMENT:ELECTRICAL; BACK OVER PREVENTION: SENSING SYSTEM: CAMERA. This preliminary informational bulletin provides repair information to correct customer concerns about blank screen after startup and reverse, rear view camera message on, touch screen inoperable, Bluetooth and navigation concerns.
PIT5507D2018-05-21. Service bulletin. BACK OVER PREVENTION: WARNINGS. This Preliminary Information communication provides information to the technician about vehicles that may have a diagnostic trouble code U0159 set in the instrument panel cluster and /or the body control module. For vehicles equipped with Ultrasonic Park Assist System Regular Production Option Code UD5 or UD7 technician will use Service Programming System to reprogram the Parking Assist Control Module to correct this concern. Technician will need to inspect the front park assist sensors scallops/reliefs molded into the ring if previously replaced. Technician will need to replace the sensor rings with part number 84075328.
PI14542018-05-07. Service bulletin. BACK OVER PREVENTION; VISIBILITY:POWER WINDOW DEVICES AND CONTROLS. This preliminary informational bulletin provides repair information for a customer concern of intermittent clicking/rubbing noise when side door glass is moving up or down at cold temperatures.
150601002E2018-05-07. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE; BACK OVER PREVENTION. This technical bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL on.
14-06-04-004A2018-05-07. Service bulletin. ENGINE AND ENGINE COOLING; BACK OVER PREVENTION. This information bulletin provides additional information to the technician on how to diagnose possible normal engine noise during a cold star and a warm engine operation.
16-NA-1072018-04-23. Service bulletin. EQUIPMENT:ELECTRICAL; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; BACK OVER PREVENTION: SENSING SYSTEM: CAMERA. This technical bulletin provides a procedure to reprogram the radio to correct a customer concern of radio Inoperative, blue Screen, AM clipping noise, HD on/off status not retained in stations, time lag on transitions, no audio with internal amp, and park assist symbol position wrong in rear view camera.
PIT5552B2018-03-12. Service bulletin. BACK OVER PREVENTION: SENSING SYSTEM: CAMERA. This Preliminary information communicates repair information for therear vision camera or surround vision camera image being: - Yellow - Blurry -Distorted - Image scrolling - Image with NO gridlines - Screen is blue with gridlines - Screen is blue with Service Rear Vision System message
PIP5446A2018-02-21. Service bulletin. BACK OVER PREVENTION. This Preliminary Information communication provides information to the technician about vehicles that have a Harsh Shift 1/2 and 2/3 and Sputter Applying Throttle Between 0 and 30%, Rough idle. Technician may find Diagnostic Trouble Codes P0101, P0171, P0172, P0174, and or P0175. Technician should inspect for cast flashing near the Mass Air Flow sensor as seen below.
PIP5168F2018-02-21. Service bulletin. POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT; BACK OVER PREVENTION; FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published “Engine Cranks But Does Not Run” diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly.
PIT5552A2018-02-21. Service bulletin. COMMUNICATION; BACK OVER PREVENTION: CAMERA SYSTEM. This Preliminary information communicates repair information for therear vision camera or surround vision camera image being: - Yellow - Blurry -Distorted - Image scrolling - Image with NO gridlines - Screen is blue with gridlines - Screen is blue with Service Rear Vision System message
PIT5277B2018-01-22. Service bulletin. BACK OVER PREVENTION: CAMERA SYSTEM; ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have intermittent and hard to duplicate Rear Camera blank, distorted, or fuzzy. Also no radio, OnStar, or speech audio and the volume is unable to be adjusted from the integrated center stack or the steering wheel controls. The driver information center will show ?No Audio? in Audio mode. Technician will need to inspect X275 and X225 for bent terminals, terminals backing out of the connector, or terminals contacting another terminal behind each side of the connector and repair as necessary.
PIT5277A2017-12-22. Service bulletin. BACK OVER PREVENTION; EQUIPMENT; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have intermittent and hard to duplicate Rear Camera blank, distorted, or fuzzy. Also no radio, OnStar, or speech audio and the volume is unable to be adjusted from the integrated center stack or the steering wheel controls. The driver information center will show ?No Audio? in Audio mode. Technician will need to inspect X275 and X225 for bent terminals, terminals backing out of the connector, or terminals contacting another terminal behind each side of the connector and repair as necessary.
PIT5386C2017-11-14. Service bulletin. ELECTRICAL SYSTEM; BACK OVER PREVENTION; BACK OVER PREVENTION: BACK-UP ALARM. This Preliminary Information communication provides information to the technician about vehicles that are found to have a back-up alarm inoperative during the Pre-Delivery Inspection. On trucks equipped with the Back Up Alarm (RPO 8S3), the alarm will be intentionally left disconnected from the assembly plant. Technician will reroute the harness and plug it in.
PIT54302017-08-15. Service bulletin. BACK OVER PREVENTION; ELECTRICAL SYSTEM:SOFTWARE; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that may have an "Object Detection Unavailable" message on the radio display when shifting into reverse. Technician should reprogram the radio using Service Programming System with the latest software.
PIT53982017-08-15. Service bulletin. BACK OVER PREVENTION: CAMERA SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that may have the rear vision camera system displaying "Rear Park Assist Symbols Unavailable" and the steering grid lines displayed do not show. Dealer will need to communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIC5611E2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; BACK OVER PREVENTION: CAMERA SYSTEM. This Preliminary Information communication provides information to the technician about the rear view camera options on the vehicles equipped with rear view camera. The rear view camera brightness can be adjusted on some models while the transmission is in reverse and using the Menu or Select button. To turn off or on the guidelines in the rear view camera, use the radio display Config icon then Display, then the guidelines option.
PIT52772017-08-15. Service bulletin. BACK OVER PREVENTION: CAMERA SYSTEM; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have intermittent and hard to duplicate Rear Camera blank, distorted, or fuzzy. Also no radio, OnStar, or speech audio and the volume is unable to be adjusted from the integrated center stack or the steering wheel controls. The driver information center will show ?No Audio? in Audio mode. Technician will need to inspect X275 for bent terminals, terminals backing out of the connector, or terminals contacting another terminal behind each side of the connector and repair as necessary.
PIT55352017-08-15. Service bulletin. BACK OVER PREVENTION; LANE DEPARTURE. This Preliminary Information communication provides information to the technician about vehicles that have that may have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Technician may find Diagnostic Trouble Code B1008 Sym 4B set. Technician will need to check the windshield to ensure it is not aftermarket. Technician will also check for anything that may impair the front view camera and ensure the camera is properly mounted.
PIT5386B2016-10-21. Service bulletin. BACK OVER PREVENTION: BACK-UP ALARM; EQUIPMENT:ELECTRICAL. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT ARE FOUND TO HAVE A BACK-UP ALARM INOPERATIVE DURING THE PRE-DELIVERY INSPECTION. ON TRUCKS EQUIPPED WITH THE BACK UP ALARM REGULAR PRODUCTION OPTION CODE (8S3), THE ALARM WILL BE INTENTIONALLY LEFT DISCONNECTED FROM THE ASSEMBLY PLANT. TECHNICIAN WILL REROUTE THE HARNESS AND PLUG IT IN.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.