Service bulletins for the 2013 Chevrolet Silverado
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
2332 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Engine are shown. Show all
| PIP4828B | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM:IGNITION. This Preliminary Information communication provides information to the technician about vehicles that have a rough idle and/or momentary lack of power after cold starting the engine and immediately placing the transmission in gear. Technician should follow published Service Information diagnostics first. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. |
|---|---|
| PIP4828A | 2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a rough idle and/or momentary lack of power after cold starting the engine and immediately placing the transmission in gear. Technician should follow published Service Information diagnostics first. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. |
| PIP4138M | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter. |
| PIT4813C | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:IGNITION; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles with a "Service Charging System" message displayed on the Driver Information Center and/or a low voltage reading on the volt gauge during the first several minutes after a cold start. Technician may find a Diagnostic Trouble Code B1517 sym 03. If this concern only occurs during the first several minutes of a cold start, no repairs should be made. Dealer should communicate to the customer that this is normal operating characteristic of vehicles equipped with the diesel engine. |
| PIT3173C | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center. |
| PIP4932B | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles with Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0101. Technician should follow published Service Information diagnostics for any Diagnostic Trouble Codes that are set. If during diagnosis the tech has found that the Airflow Leak Equivalency Ratio or Induction System Leak Indication is above or below the specification the tech will have to carefully check for leaks in the air intake. |
| PIP5069 | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that have a lack of power on initial acceleration from a stop when the ambient temperature is approximately 103 Fahrenheit or greater and may include engine detonation or pre-ignition type events as temperatures approach 120 Fahrenheit. Technician will need to perform published Service Information diagnosis first. If Service Information diagnosis does not isolate the cause of this concern, take a Tech 2 snapshot of the concern happening and note the Spark Parameter in the Ignition Data List. If it drops near/below 0 degrees during the concern, check if there is a cylinder that shows any knock. If there is a knock in any cylinder perform a top engine clean. If the concern is still present, then switching to premium fuel (91 octane or higher) with detergents (Top tier fuel) when ambient temperatures exceed 110 Fahrenheit degrees, this should provide a slight improvement in engine performance when ambient temperatures are high especially as temperatures approach 120 Fahrenheit degrees. |
| PIP4568P | 2017-08-15. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed. |
| PIP5161 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on a rough running engine, and/or oil consumption. Technician will find Diagnostic Trouble Code P0300 set. Technician will apply regulated air pressure through the PCV pipe and spray soapy water where the PCV baffle and valve cover meet with soapy water to inspect for possible signs of a leak. Technician will replace the value cover if a leak is present. |
| PIP4765A | 2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have Service Engine Soon Malfunction Indicator Lamp on and a constant engine misfire. If Service Information diagnosis isolates no compression on the misfiring cylinder(s) with 100% leakage into the crankcase, perform the following steps as necessary before disassembling the engine. Technician will use a lighted bore scope if available to inspect the top of the related piston(s) through the spark plug hole to determine if any of the pistons are melted. If damaged piston(s) are found inspect for aftermarket parts. Also use the latest version of 09-06-04-026 to verify if there are aftermarket calibrations in the Engine Control Module. Take photos and document accordingly if anything is found. |
| PIP4912B | 2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE. This Preliminary Information communication provides information to the technician on vehicles that may have an intermittent high idle. If a technician has duplicated, or the customer description aligns with the speeds mentioned in the idle speed description tables, the idle speed should be considered a normal characteristic of current vehicle design. |
| PIP5163 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure. |
| 06-06-01-010C | 2017-08-15. Service bulletin. ENGINE. This informational bulletin provides information on close coupled converters and there affect on newly installed engines or engines during there break in period. |
| PIP5226 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings. |
| PIP5085C | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on. Technician may find a P0420, P24A0 and/or P2463 set. Technician should use published Service Information diagnostics for the Diagnostic Trouble Code. If the diagnostic leads to diagnosis or replacement of the Q57 Indirect Exhaust After treatment Fuel Injector, document all of your test results. |
| PIP5085B | 2017-08-15. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on. Technician may find a P0420, P24A0 and/or P2463 set. Technician should use published Service Information diagnostics for the Diagnostic Trouble Code. If the diagnostic leads to diagnosis or replacement of the Q57 Indirect Exhaust After treatment Fuel Injector, document all of your test results. |
| PIP4864N | 2017-08-15. Service bulletin. FUEL SYSTEM, DIESEL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that may have "Exhaust Fluid Low", "Exhaust Fluid Empty - Refill Now", "Exhaust Fluid Range: XXX" or "Service Exhaust Fluid - See Owners Now" on the Driver Information Center. If the technician is working on 2010 and 2011 model years campaign 11001 has now been released. Other vehicles technician will need to check the Body Control Module and the scan tool to insure the latest calibration are installed in both. Then use the scan tool to check Reductant System Data in the Engine Control Module. Ensure that all three diesel exhaust fluid level sensors are active with the diesel exhaust fluid tank level showing 100%. If the tank level is below 100% add up to 2 gallons of diesel exhaust fluid. After adding the fluid, use a scan tool to reset the reductant fluid tank level. When the reductant level warning shows "none" the diesel exhaust fluid system reset and reprogram is complete. |
| PIP4932C | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles with Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0101. Technician should follow published Service Information diagnostics for any Diagnostic Trouble Codes that are set. If during diagnosis the tech has found that the Airflow Leak Equivalency Ratio or Induction System Leak Indication is above or below the specification the tech will have to carefully check for leaks in the air intake. |
| PIP4912C | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician on vehicles that may have an intermittent high idle. If a technician has duplicated, or the customer description aligns with the speeds mentioned in the idle speed description tables, the idle speed should be considered a normal characteristic of current vehicle design. |
| PIP5007D | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. This Preliminary Information communication advises the technician that vehicles with engine Regular Production Option Code LGH or LML may have an Exhaust Fluid Quality Poor message displayed on the Driver Information Center. Technician will need to complete the current Service Information diagnostic for any current Diagnostic Trouble Codes or symptoms found. If an Exhaust Fluid Quality Poor message is displayed with a specific Diagnostic Trouble Code, use that specific Service Information diagnostic, and repair the vehicle as necessary. If the dealer has found an Exhaust Fluid Quality Poor message with no Diagnostic Trouble Code, diagnose the condition using the current Service Information diagnosis for Diagnostic Trouble Code P20EE / P207F (P2BAD for 2012 and newer model years). After making repairs use the Service Information Document titled "Reductant Fluid Quality Test (With or without Diagnostic Trouble Codess)" to evaluate and clear the Exhaust Fluid Quality Poor Driver Information Center message. |
| PIP5163A | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure. |
| PIP3783D | 2017-08-15. Service bulletin. ENGINE; VEHICLE SPEED CONTROL:ACCELERATOR PEDAL. This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on or reduced engine power message. Technician may find Diagnostic Trouble Codes P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138. Technician will need to inspect the Accelerator Pedal Position circuits for poor terminal tension. |
| PIT4821D | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM:12V/24V/48V BATTERY. This Preliminary Information communication advises the technician that the 2-Mode Drive Motor Generator Battery placed on parts restriction by General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance. |
| PIP3119M | 2017-08-15. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. |
| PIP5168A | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published "Engine Cranks But Does Not Run" diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.