WenmarOpen by Wenmar Pro

Service bulletins for the 2010 Chevrolet Silverado

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

1956 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Fuel system are shown. Show all

Bulletins, newest first
04-06-04-051E2018-05-21. Service bulletin. EQUIPMENT; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS. This informational bulletin provides information for maintenance cleaning of the fuel injectors.
04-06-04-051D2018-05-21. Service bulletin. EQUIPMENT; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS. This informational bulletin provides information for maintenance cleaning of the fuel injectors.
03-06-04-017K2018-05-21. Service bulletin. EQUIPMENT; FUEL SYSTEM, DIESEL. This Informational Bulletin provides information on availability of Diesel Fuel additives.
03-06-04-017J2018-05-21. Service bulletin. FUEL SYSTEM, DIESEL; EQUIPMENT ADAPTIVE/MOBILITY. This Informational Bulletin provides information on available Diesel Fuel Additives.
18NA1032018-05-21. Service bulletin. FUEL SYSTEM, GASOLINE. This Technical Bulletin provides information to correct a customer concern of a siren or whine noise from the in-tank fuel pump at temperatures below -6C or 20F, accompanied by start and stall, no start, loss of power and MIL illuminated. Technicians may find DTCs P0087, P018B, P228A, P228B or P2635 set in ECM.
16NA1022018-05-07. Service bulletin. FUEL SYSTEM, GASOLINE. This technical bulletin provides a procedure to clean and repair the complete fuel system due to dirt getting into the fuel system causing the vehicle to have a hard or no start.
050604022N2018-05-07. Service bulletin. FUEL SYSTEM, GASOLINE. This informational bulletin provides information on the top tier fuels that are recommended in GM vehicles.
040604051D2018-05-07. Service bulletin. FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS. This informational bulletin provides information for maintenance cleaning of the fuel injectors.
05-00-89-072C2018-04-16. Service bulletin. FUEL SYSTEM, OTHER; FUEL SYSTEM, GASOLINE; FUEL SYSTEM, DIESEL. This informational bulletin provides information on how to save fuel and proper maintenance without using fuel or oil additives.
PIP5168F2018-02-21. Service bulletin. POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT; BACK OVER PREVENTION; FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published “Engine Cranks But Does Not Run” diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly.
PIP3343F2018-02-21. Service bulletin. COMMUNICATION; FUEL SYSTEM, OTHER:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS. This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Technician will need to clean the area of the oil leak, clean and dry the PCV hoses, and replace the oil fill cap with part number 12589430.
PIP53252018-01-22. Service bulletin. FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician to help determine if the vehicle is equipped with factory or aftermarket Compressed Natural Gas, Liquefied Petroleum Gas, or Bi-Fuel Systems. Technician will check for the Vehicle Emission Control Information Label. By using the engine Regular Production Option Code as well as the Vehicle Emission Control Information Label, technician can confirm the vehicle has a factory installed alternative fuel system or who the manufacturer is of the aftermarket fuel system.
06-06-01-007I2017-12-22. Service bulletin. ENGINE AND ENGINE COOLING; FUEL SYSTEM, DIESEL. This informational bulletin provides information to dealership personnel on identifying Duramax Diesel overpower engine breakdown or non-function due to aftermarket power-up devices vs. non overpower engine non-function of pistons, cylinders, valve train components, and DTC P003A or P111D set.
PIP4898B2017-12-22. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE. This Preliminary Information communication provides information to the technician about vehicles that may have an engine buzz, moan, rattle, whine, or vibration type noise that can typically be heard at idle or low revolutions per minute. The noise does not indicate a problem and will not result in damage to the pump or the engine. If the customer is dissatisfied with the oil pump whine noise replacement of the oil pump will resolve the concern.
PIP5151B2017-12-22. Service bulletin. FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that may have a hard start, no start, rough running, or low fuel pressure. Technician may find Diagnostic Trouble Codes P0087, P0088, P0191 and P128E during the inspection. If during the inspection of the fuel system contamination is found the complete fuel system will need to be cleaned and flushed. After the fuel system is cleaned out test the fuel using the latest version of PIT3173.
PIP4379M2017-12-22. Service bulletin. POWER TRAIN; FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician about vehicles that have not engagement into drive, delayed, no engagement into reverse, and or a range inhibit. Technician may find Diagnostic Trouble Codes P0701, P0731, P0732, P0733, P0734, P0736, P0751, P0756, P0761, P0776, P0843, P0848, P0873, P0877, P0894 or P2723. Technician should follow published Service Information diagnostics for Diagnostic Trouble Code P0701 first. Technician will also ensure the fluid level is at the top of the hot band when the transmission fluid temperature is 175° Fahrenheit. Diagnostic Trouble Codes P0701, P0731, P0732, P0733, P0734, P0736, P0751, P0756, P0761, P0776, P0843, P0848, P0873, P0877, P0894 or P2723 can set by the following fluid service/filter change, transmission service involving removing the pan, low fluid level caused by leaks, or after long periods of storage. If the fluid level has been properly checked using the HOT check procedure listed in Service Information document 2408059 and any of the Diagnostic Trouble Codes reset during a cold start inspect the internal suction filter for possible cracks. If no other concerns are found inspect for a stuck lube regulator valve in the pump cover due to debris.
PIT5161F2017-11-14. Service bulletin. FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. The bump clunk issue may be due to fuel movement in the fuel tank when not completely full. The condition is eliminated after completely filling the fuel tank.
PIP4436C2017-10-15. Service bulletin. EQUIPMENT; FUEL SYSTEM, DIESEL. This Preliminary Information communication provides information to the technician about vehicles that have an engine noise, low oil pressure, over-speed condition, or abnormal oil sludge build up in the crankcase. Technician should follow published Service Information diagnosis for the DTCs found. If an excessive amount of sludge is found in the crankcase the vehicle may be running a high percentage of Bio-fuel. Technician should verify the oil change records and verify proper oil change intervals are being followed. Technician should be advised to use the Duramax Diesel Owner?s Manual Supplement for guidelines on proper fuel usage.
05-00-89-072D2017-10-15. Service bulletin. FUEL SYSTEM, GASOLINE. This informational Bulletin provides Do's and Don'ts for maximizing gasoline engine fuel economy, other various tips and a list of websites for additional information.
08-06-04-006K2017-10-12. Service bulletin. FUEL SYSTEM, DIESEL; ENGINE AND ENGINE COOLING:ENGINE:DIESEL. This informational bulletin provides information for Identifying Non-GM ECM Calibration Use and Power-up Hardware Detection in Duramax Diesel Engines - Photograph Tech 2 Calibration IDs, Calibration Verification Numbers (CVNs) and Transmission Data Screen
16-NA-1022017-08-31. Service bulletin. FUEL SYSTEM, GASOLINE. This technical bulletin provides a procedure to clean and repair the complete fuel system due to dirt getting into the fuel system causing the vehicle to have a hard or no start.
PIT5161C2017-08-15. Service bulletin. FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY; FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. The bump clunk issue may be due to fuel movement in the fuel tank when not completely full. The condition is eliminated after completely filling the fuel tank.
PIP53392017-08-15. Service bulletin. FUEL SYSTEM, OTHER. This Preliminary Information communication provides information to the technician about a customer?s request to remove or disable the Bi-Fuel Compressed Natural Gas system. General Motors does not condone the removal of the original equipped Compressed Natural Gas systems.
PIP4949E2017-08-15. Service bulletin. FUEL SYSTEM, OTHER:DELIVERY:FUEL PUMP; FUEL SYSTEM, OTHER:FUEL INJECTION SYSTEM; FUEL SYSTEM, OTHER:FUEL FILTER. This Preliminary Information communication provides information to the technician about vehicles that have a hard start or a no start. Technician may find Diagnostic Trouble Code DTCs P0087, P0088, P0191 or P128E. Technician will need to follow all Service Information diagnose for the Diagnostic Trouble Code. If the current Service Information diagnostic has led to Fuel Injection Pump replacement, Fuel Pressure Regulator 1 must be inspected for magnetic metal debris. If there is a questionable amount of magnetic debris found on Pressure Regulator 1 remove the Fuel Rail Pressure Sensor and/or Fuel Pressure Regulator 2 to inspect for magnetic metal debris. If technician will need to replace all of the parts listed under the latest version of PIP4949 found in the Service Forms section of Global Connect if debris is found. Clean and flush all fuel chassis lines, filter pipes, and other engine mounted fuel system pipes not replaced. Also the fuel filter housing must be cleaned with a new fuel filter installed. Then the fuel tank and fuel sender must be cleaned and flushed.
PIT4943D2017-08-15. Service bulletin. FUEL SYSTEM, GASOLINE; FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.