WenmarOpen by Wenmar Pro

Service bulletins for the 2004 Chevrolet Silverado

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

1089 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
PIP3119L2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.
PIP3394F2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have Misfire, rough running, surge, chuggle, and possible Service Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P1223, P1226, P1229, P1232, P1235, P1238, P1241 or P1244. Technician should check the wiring between the Engine Control Module and the Fuel Injection Control module. Also inspect the C107 on Silverado and Sierra or C118 on Kodiak and Topkick connector for wire chafes. Technician should repair any wiring issues that are found.
PIT4780M2017-08-15. Service bulletin. EQUIPMENT:MECHANICAL; EQUIPMENT:ELECTRICAL; HYBRID PROPULSION SYSTEM. This Preliminary Information communication advises the technician that the 2004-2007 Parallel Hybrid Truck parts will be placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
PIP4972C2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that will not move in forward or reverse. Technician may find Diagnostic Trouble Code P0877 or P2723 set. Technician will need to inspect the valve body separator plate orifices for debris.
PIP3140E2017-08-15. Service bulletin. EQUIPMENT. This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
PIT3227H2017-08-15. Service bulletin. STRUCTURE:BODY:TAILGATE. This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables. Technician should not replace any parts for this concern. Please communicate to the customer this condition is a normal operating characteristic of their vehicle.
PIP4290A2017-08-15. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicles that have a surge or stall when in gear at a stop. Technician will find Diagnostic Trouble Code P0742. Technician will need to isolate if the concern is transmission internal or external. Technician will need to disconnect the 20 way connector at the transmission (C-175 for model years 2001 ? 2007 and X-175 for model years 2008 ? 2013). On 2006 ? 2013 model years, using a fused jumper wire, connect terminal R of the automatic transmission inline 20-way connector to a known good ground. Technician can now run the vehicle to duplicate the concern. If the vehicle still stalls the concern has been isolated to the transmission. Inspect the Torque Converter Clutch solenoid and valve in the main valve body. If the vehicle does not stall inspect wiring between the Transmission Control Module and transmission if no concern is found swap the Transmission Control Module into a known good vehicle after clearing any Diagnostic Trouble Codes to determine if the concern follows the Transmission Control Module.
PIP50942017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.
PIP3497B2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER. This Preliminary Information communication provides information to the technician about vehicles that have no forward or reverse. Technician will need to check for metal debris in torque converter clutch valve.
PIP3119K2017-08-15. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.
08-07-30-026C2017-08-15. Service bulletin. ELECTRICAL SYSTEM:STARTER ASSEMBLY. This informational bulletin provides information on vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak and that this is considered a normal conditon and no repairs are necessary
PIT51952017-08-15. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 miles per hour at any given speed when looking straight at the needle.
PIP4138M2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
PIP4138L2017-08-15. Service bulletin. EQUIPMENT:MECHANICAL; POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
PIP3259J2017-08-15. Service bulletin. POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicles that may have a planetary gear whine noise in first and second gear. Technician should compare the noise to a like vehicle. Technician will need to check the build date of the transmission, if it was built after 09/01/2003 and it is determined that a vehicle has an abnormal amount of noise, perform the rear unit end play check. Technician will replace the output planetary gear set if end play is out of specification. The transmission assembly will need to be replaced if the end play is with in specification.
PIC3718E2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles may have a no power or no connect concern. Technician will find that the OnStar led is red and Diagnostic Trouble Code U1500 is set. Technician will need to replace the Vehicle Communication Interface Module if the Station Identification number falls in the ranges 14,000,000 - 16,000,000 or 22,000,000 - 23,200,000.
PIT3271F2017-08-15. Service bulletin. TIRES; WHEELS. This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIT3173C2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.
PIT3330F2017-08-15. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. This Preliminary Information communication provides information to the technician about customers may inquire about the availability of the passenger compartment air filter. Dealer should advise the customer starting in 2003 the passenger compartment air filter is no longer available as a factory option.
PIC4310H2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIP3720D2017-08-15. Service bulletin. POWER TRAIN:AXLE ASSEMBLY. This Preliminary Information communication provides information to the technician with the axel setup information from American Axle Manufacturing. Technician should be advised that the maximum pinion shim to be used or stacked behind the pinion is 0.050?, and the minimum pinion shim is 0.020? for an 8.6 axle. The range for available pinion depth shims for the 10.5? axle is 0.006? to 0.024?. When setting the backlash it should be set between 0.003? to 0.005? on a new ring and pinion for any American Axle Manufacturing application. The ring and pinion can be reused or adjusted if the mileage is less than 500 miles, if not used for towing. Technician should be advised that a ?roller coaster? or ?hourglass? pattern on the bearings may be normal up to 10,000 miles and possibly longer. With a mis-machined housing you may get a heel pattern on both sides of the gear teeth at build up can generally be corrected with backlash adjustments. When setting up an 8.6? axle with a 5 cut gear set is to use a 0.035? pinion shim and set backlash to 0.004?. When using the newer 2 cut gear set also use a 0.035? pinion shim and still set backlash to 0.004?. To set the gear pattern use backlash to adjust the pattern heel to toe. Use the pinion shim to adjust the height of the pattern. The proper drive pinion bearing pre-load is from 15 - 30 inch pounds with new bearings. The total torque to turn after the differential case is installed should increase 5 - 10 inch pounds at the pinion. A new pinion nut must be used whenever the old one is removed. The axle shaft end play specification is 0.012? per side and the radial specification is 0.002? - 0.003?. Technician should be advised that synthetic lube can be used in all new American Axle Manufacturing axle assemblies. The new pinion seal for the 8.6? axle assembly is a two piece design.
PIT4907A2017-08-15. Service bulletin. SERVICE BRAKES. This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and replacement parts from General Motors Service Parts Operations. Technician should be advised the costing should not be removed from the brake rotor it will wear off with normal brake usage. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
PIT3665C2017-08-15. Service bulletin. SERVICE BRAKES; SERVICE BRAKES, HYDRAULIC. This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
PIT4208D2017-08-15. Service bulletin. SERVICE BRAKES, HYDRAULIC:POWER ASSIST; STEERING:HYDRAULIC POWER ASSIST:POWER STEERING FLUID. This Preliminary Information communication provides information to the technician about vehicles that may have a power steering pump whine noise. Technician will need to flush and refill the power steering system with Lucas Power Steering Fluid with Conditioners. Technician will replace the power steering pump with the latest design if the fluid is not available.
PIC4935D2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.