WenmarOpen by Wenmar Pro

Service bulletins for the 2013 Chevrolet Malibu

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

2002 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
PI0653C2017-12-22. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER. This preliminary informational bulletin provides dealership personnel with policies and procedures regarding damaged, disassembled or improperly packaged turbochargers returned to Warranty Part Center.
GCUS-9-28162017-12-22. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. 15824-01 - Special Coverage (warranty information revised). Some vehicles (Intake Camshaft Position Actuator Solenoid Valve Control Circuit) or P0013 (Exhaust Camshaft Position Actuator Solenoid Valve Control Circuit) diagnostic trouble code (DTC) may set as a result of an internal broken wire in the intake or exhaust camshaft position actuator solenoid. If this occurs within the stated time frame dealer will replace the intake or exhaust camshaft position actuator solenoid valve as necessary.
00-06-01-026H2017-12-22. Service bulletin. ENGINE. This informational bulletin provides information on intake manifold inspection/replacement after severe internal engine damage.
PIP4112P2017-12-22. Service bulletin. ENGINE; POWER TRAIN. This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
PI0653D2017-10-15. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER. This preliminary informational bulletin was created to inform Service Agents or Dealers, they may be charged back for parts and labor due to the turbo-chargers are being returned to the Warranty Parts center damaged, improperly assembled or missing parts and advising to properly package the complete turbochargers. (New models and RPOs added)
09-06-04-026E2017-10-12. Service bulletin. ENGINE AND ENGINE COOLING. This informational bulletin provides information on Identifying Non-GM (Aftermarket) Engine Calibrations for Gasoline Engines Using Tech 2 or GDS 2
17-NA-0392017-08-31. Service bulletin. ENGINE. This informational bulletin provides additional information on what oil to use in the 2.0L engines to eliminate the risk of engine/piston failure.
PIP5232B2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIP53002017-08-15. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that engine overheating, and/or poor heater performance, AC off message, and Malfunction Indicator Lamp illumination. Technician will find Diagnostic Trouble Code P00B7 and/or P2181. Technician will gain access to the water outlet assembly and inspect for flashing or debris. If flashing or debris found in the water outlet assembly it will need to be replaced. Also inspect the upper heater core hose and coolant bypass pipe at the water outlet for a black plug. If plug is found, remove and discard.
PIT4943D2017-08-15. Service bulletin. FUEL SYSTEM, GASOLINE; FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
PIP4548E2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. This Preliminary Information communication advises the technician what to inspect if codes P0016 and/or P0017 are setting on a properly timed engine or a condition of the vehicle cranks but will not start. Technician should inspect the respective intake or exhaust camshaft reluctor to see if it has spun on the camshaft. The reluctor cannot be repositioned so the camshaft must be replaced. The new camshafts come with the reluctor already pressed on in the correct position.
PIP5163B2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; FUEL SYSTEM, GASOLINE; ENGINE. This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIP52472017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P06DE set in the Engine Control Module. Technician must follow published Service Information diagnostics for P06DE. If diagnostics lead to removing the oil pan or engine oil pressure is below specification when hot, to inspect the oil piston nozzles for damage. Technician should replace the broken oil nozzle(s) as long as the engine does not have any damage which warrants engine replacement.
PIP5029F2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.
PIC60402017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE. This Preliminary Information communication advises the technician that during reassembly after a heavy engine repair it is very possible for a technician to accidentally switch the G13 generator X1 connector with the B35 engine oil level switch connector.
PIC5520P2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. This Preliminary Information communication advises the technician that the Drive Motor Generator Battery Module and Drive Motor Generator Battery Sections for the 2012 - 2015 Buick Lacrosse, Buick Regal, 2013 - 2014 Chevrolet Malibu ECO and 2014 Chevrolet Impala with eAssist are being placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
PIP52822017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication advises the technician about the calculation and operation of the engine oil life monitor. The monitor calculates the percent of oil life remaining, based on 3 pathways. The first pathway for oil life calculation is engine revolutions. The second pathway for oil life calculation is the mileage form the last rest for all General Motors powertrains except the Volt. The third pathway for oil life calculation is the amount of time the oil is in the engine. The Volt uses a 2 year timer instead of 1 year. It also uses the engine revolution counter. It does not use the mileage pathway to count down.
G-1743722017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. 13283 - Service Update. An analysis of engine build data revealed that there could be a durability issue with the engines originally installed in these vehicles. To ensure the highest quality and best ownership experience for our customers, these engines need to be replaced prior to vehicle delivery.This bulletin provides a service procedure to replace the engine assembly on certain vehicles equipped with 4 cylinder engine (RPO LCV or LKW). Due to a casting error, these vehicles may have engine pistons that are dimensionally incorrect. Over time, contact between the cylinder valves and the piston could result in engine noise, rough running and/or bent valves.
G-1707122017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. 13013B - Service Update (revised service procedure). Tighten all 4 exhaust manifold bolts. The ring gasket may be pinched between the flanges on the inside diameter of the joint leading to a visible gap. As the pinched part of that gasket relaxes, clamp load is lost at that stud location.
G-1588402017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. 13013A - Service Update (revised service procedures ). The ring gasket may be pinched between the flanges on the inside diameter of the joint leading to a visible gap. As the pinched part of that gasket relaxes, clamp load is lost at that stud location. Dealers are to tighten all 4 exhaust manifold bolts.
PI1223B2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. This informational bulletin provides information on black smoke and rough idle on cold start.
09-06-04-026M2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ENGINE. This informational bulletin provides information on identifying non-GM (aftermarket) engine calibrations for gasoline engines using Tech 2 or GDS 2.
PIP5232C2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the coil grounds ring terminal at the engine block for the bank with the concern and repair the wire.
11-00-90-001A2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This informational bulletin provides information on the proper oils to use on GM vehicles including information regarding the differences of the Dexos oils.
00-06-01-026G2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This informational bulletin provides information to technicians regarding intake manifold inspection/replacement after severe internal engine damage.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.