WenmarOpen by Wenmar Pro

Service bulletins for the 2015 Chevrolet Express

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

1563 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
GCUS-9-31402017-12-22. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL; FUEL SYSTEM, DIESEL. 29400 Special Coverage. Certain vehicles that are equipped with a diesel engine (RPO LML/LGH/LUZ), a malfunction-indicator light (MIL) may illuminate due to an offset in the temperature sensor in the diesel-emission-reduction fluid (DEF) tank reservoir or increased DEF tank-heater resistance. Dealers are to replace the DEF tank reservoir. The repairs will be made at no charge to the customer.
00-06-01-026H2017-12-22. Service bulletin. ENGINE. This informational bulletin provides information on intake manifold inspection/replacement after severe internal engine damage.
GCUS-3-5532017-12-22. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ENGINE. 15801 - Customer Satisfaction Program. (2012 model year repair suspended) Vehicles equipped with Duramax Diesel Engine (RPO LGH or LML) and Ambulance Upfitter or Fire Truck Upfitter (RPO YF2 or ANM), may have a condition in which the emission control system as designed will limit speed under certain conditions. The EPA has approved General Motor?s request to remove the emission control system speed limitations on these emergency vehicles where applicable. Dealers are to reprogram the Engine Control Module (ECM) with new calibration for emergency vehicles, which will remove the emission control system speed limitations, and also provide an earlier warning for Diesel Particulate Filter (DPF) regeneration.
PIT5202D2017-12-14. Service bulletin. ENGINE; POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicles that are equipped with 6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option Code (M5U) Automatic Transmission, now have Powertrain Grade Braking. Powertrain grade braking assists when driving on a downhill grade to help maintain desired vehicle speed by using the engine and transmission to slow the vehicle.
GCUS-9-8982017-11-17. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. 15457 - Special Coverage. Some 2010-2015 Chevrolet Express and GMC Savana vehicles and 2011-2015 Chevrolet Silverado HD and GMC Sierra HD vehicles that are equipped with 6.6L Duramax Diesel engines (RPO LML or LGH) may contain a leak in the seal between the engine-exhaust down pipe and the engine-exhaust pipe. If a leak is present, the intermittent regeneration of the diesel-particulate filter may cause small amounts of diesel fuel to leak from the vehicle. It may also cause diesel-fuel vapor and engine exhaust to enter the passenger cabin. Dealers are to inspect the turbocharger exhaust pipe and the downpipe connection and implement service kit if necessary.
GCUS-3-2892017-11-17. Service bulletin. ENGINE. 14287 - Customer Satisfaction Program. On certain 2003-2015 model year Chevrolet Express, 2003-2007 Chevrolet Silverado, 2008-2013 Chevrolet Silverado HD, 2003-2015 GMC Savana, 2003-2007 GMC Sierra 3500, and 2007-2012 GMC Sierra HD model vehicles equipped with a Duramax diesel engine and an engine-block heater (RPO YF2 and K05), continuously activating the engine-block heater through Ambulance body up fit ?shore power? may cause excessive heat buildup, cause a high-resistance short, damage the engine-block heater, or, in rare cases, melt electrical connections or cause an engine-compartment fire. Dealers are to: Replace block heater element with a revised heater equipped with EPDM O-Rings, shorter bolt and improved torque & angle. Disconnect the coolant heater from being powered whenever ?shore power? is plugged in. Add a label to the current cord, ?Avoid continuous use, for Cold Start Only?, unless the cord is damaged at either end, then replace the original cord. Provide the customer with an Owner?s Manual Insert found at the end of this bulletin.
PIP5370A2017-10-15. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL. This Preliminary Information communication provides information to the technician that some vehicle may have an ?Exhaust Fluid Quality Poor? on the Driver Information Center or a diesel exhaust fluid warning lamp on or other exhaust fluid quality related concerns. Technician will inspect the diesel exhaust fluid for contamination. Technician should use Service Information for Contaminants in Diesel Exhaust Fluid Diagnosis and use special tool J26568 or EN50422 Diesel Exhaust Fluid Refractometer for fluid testing.
PIP5088E2017-10-15. Service bulletin. ENGINE. This Preliminary Information communication advises the technician that the parts restriction has ended on the 6.6L Duramax engine Regular Production Option Code (LML/LGH) part number 12638502. Dealer can now order parts through the normal Customer Care and Aftersales parts process.
PI0653D2017-10-15. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER. This preliminary informational bulletin was created to inform Service Agents or Dealers, they may be charged back for parts and labor due to the turbo-chargers are being returned to the Warranty Parts center damaged, improperly assembled or missing parts and advising to properly package the complete turbochargers. (New models and RPOs added)
PIP5232B2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIP4864P2017-08-15. Service bulletin. FUEL SYSTEM, DIESEL:STORAGE:TANK ASSEMBLY; FUEL SYSTEM, DIESEL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that may have "Exhaust Fluid Low", "Exhaust Fluid Empty - Refill Now", "Exhaust Fluid Range: XXX" or "Service Exhaust Fluid - See Owners Now" on the Driver Information Center. If the technician is working on 2010 and 2011 model years campaign 11001 has now been released. Other vehicles technician will need to check the Body Control Module and the scan tool to insure the latest calibration are installed in both. Then use the scan tool to check Reductant System Data in the Engine Control Module. Ensure that all three diesel exhaust fluid level sensors are active with the diesel exhaust fluid tank level showing 100%. If the tank level is below 100% add up to 2 gallons of diesel exhaust fluid. After adding the fluid, use a scan tool to reset the reductant fluid tank level. When the reductant level warning shows "none" the diesel exhaust fluid system reset and reprogram is complete.
PIP5258A2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find a Diagnostic Trouble Code P0011. If the technician has followed all published Service Information diagnosis and has not come to a conclusion, technician should check the oil pressure at the oil pressure sender. Then the number two cam bearing should be inspected.
PIP4932D2017-08-15. Service bulletin. ENGINE; EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician about vehicles with Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0101. Technician should follow published Service Information diagnostics for any Diagnostic Trouble Codes that are set. If during diagnosis the tech has found that the Airflow Leak Equivalency Ratio or Induction System Leak Indication is above or below the specification the tech will have to carefully check for leaks in the air intake.
PIP5016B2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:ENGINE:DIESEL. This Preliminary Information communication provides additional information to the technician when replacing the Duramax Diesel head gasket. This is a supplement to procedure found in Service Information. The left and right cylinder head gaskets are not interchangeable and will block oil and coolant passages if installed incorrectly resulting in severe damage to the engine. Technician is not use any power sanding devices, wire brush or wheel as well as any chemical cleaning agents to clean the gasket surface. Leave the gaskets in the package until the surfaces are ready to install them. Do not set the gaskets on workbenches or tool boxes to avoid introduction of foreign debris. The cylinder head surface is not to be machined measure the head for warpage with a straight edge and feeler gauge replacing the head with warpage in excess of .1 millimeter. All M12 head bolts must be replaced however the M8 bolts can be reused. Install 2 head bolts secured at minimal torque to minimize the chance of introducing foreign material. Use a paint pen on the M12 bolts marking the head of each bolt indicating which of the 4 torque steps have been completed to prevent missing a step or doing a step twice.
PIP4864Q2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:DIESEL. This Preliminary Information communication provides information to the technician about vehicles that may have "Exhaust Fluid Low", "Exhaust Fluid Empty - Refill Now", "Exhaust Fluid Range: XXX" or "Service Exhaust Fluid - See Owners Now" on the Driver Information Center. If the technician is working on 2010 and 2011 model years campaign 11001 has now been released. Other vehicles technician will need to check the Body Control Module and the scan tool to insure the latest calibration are installed in both. Then use the scan tool to check Reductant System Data in the Engine Control Module. Ensure that all three diesel exhaust fluid level sensors are active with the diesel exhaust fluid tank level showing 100%. If the tank level is below 100% add up to 2 gallons of diesel exhaust fluid. After adding the fluid, use a scan tool to reset the reductant fluid tank level. When the reductant level warning shows "none" the diesel exhaust fluid system reset and reprogram is complete.
PIT4943D2017-08-15. Service bulletin. FUEL SYSTEM, GASOLINE; FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
PIT5058C2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE. This Preliminary Information communication provides information to the technician about the operation and diagnostics of the Regular Production Option Code UJ1 brake warning pressure warning system. The technician can test the operation of the brake warning system. If the warning system does not function correctly, technician will need to inspect circuit 33 for a short to ground between X141 and the Instrument Panel Cluster terminal 14. Then inspect check circuit 33 for an open between X141 and the Instrument Panel Cluster terminal 14. Also technician should check male side of X141 circuit 33 with an ohm meter to ground and should be close to 0 ohms with engine off and key on. Start engine and circuit should go (OL) indicating that the flow switch opened. Then, turn the steering to the stop in pressure relief and verify that the circuit stays (OL) to check the operation of the pressure switch.
PIP3504D2017-08-15. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE; FUEL SYSTEM, DIESEL. This Preliminary Information communication provides information to the technician about vehicles that have a hard start when the engine is hot. If the fuel found in the vehicle has an American Petroleum Institute specific gravity reading of 39 - 44, and the fuel sample you used for comparison has an American Petroleum Institute specific gravity reading of 30 - 39, drain the fuel system and refill with a known good diesel fuel and retest.
PIP5163B2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; FUEL SYSTEM, GASOLINE; ENGINE. This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIP5204D2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL; FUEL SYSTEM, DIESEL. This Preliminary Information communication advises the technician that the Diesel Oxidation Converter part numbers 15231895, 22768282, 22770967, 22887212, 22893734 and 22977171 will be placed on a parts restriction through the General Motors Product Quality Center. Dealer will need to contact the General Motors Product Quality Center for further assistance.
PIP5029F2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.
PIP5088C2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL. This Preliminary Information communication advises the technician that the 6.6L Duramax Diesel Engine Part number 12638502 has been placed on a parts restriction through the General Motors Product Quality Center. Dealer will need to contact the General Motors Product Quality Center for further assistance.
PIP5152B2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:ENGINE:DIESEL. This Preliminary Information communication provides information to the technician on the proper steps for filling the coolant system for vehicles with a diesel engine and rear heater systems. Dealer will need to review and use Service Information procedures for Cooling System Draining and Filling (Vac-N-Fill Diesel) after all cooling system repairs are made. When filling the cooling systems on vehicles that have been up-fitted with rear heaters, such as ambulances or buses, ensure that the rear heater is purged of all air.
PIP5110C2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. This Preliminary Information communication provides information to the technician of additional information while diagnosing a diagnostic trouble code P0420. Check for a possible leak in the exhaust system behind the bank one number 2 oxygen sensor. If a leak is found or there is an aftermarket utility bed or trailer hitch installed. Check for a minimum clearance of 1.5 to 2 inches of the exhaust system. Install a new clamp and torque it to 40.5 foot pounds.
PIP5110B2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. This Preliminary Information communication provides information to the technician with additional information while diagnosing a diagnostic trouble code P0420. Check for a possible leak in the exhaust system behind the bank one number 2 oxygen sensor. If a leak is found or there is an aftermarket utility bed or trailer hitch installed. Check for a minimum clearance of 1.5 to 2 inches of the exhaust system. Install a new clamp and torque it to 40.5 foot pounds.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.