Service bulletins for the 2011 Chevrolet Equinox
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1768 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| PIP5203C | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about a service engine soon light on. Technician will find diagnostic trouble codes P0089 and P228D set in the engine control module. This concern could be due to an incorrect intake camshaft or camshaft actuator sprocket. A diagnostic trouble code of P0171 could also set from installing incorrect injectors. |
|---|---|
| PIP5203B | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about a service engine soon light on. Technician will find diagnostic trouble codes P0089 and P228D set in the engine control module. This concern could be due to an incorrect intake camshaft or camshaft actuator sprocket. A diagnostic trouble code of P0171 could also set from installing incorrect injectors. |
| PIC5322D | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication advises the technician of a customer concern where the heated seat indicator light is not functioning or the heated seats are not up to operating temperature during a remote vehicle start event. This is normal operation of the heated seat during a remote vehicle start event. The electronic climate control module is not in a complete wake up state during a remote vehicle start mode and will not enable the light emitting diode. After a cold soak below 32 degrees Fahrenheit the seat will not get hot in the 10 minutes or less of the remote vehicle start mode. This is due to the fact that the heat element is not in direct contract with the seat surface while the seat is unoccupied and the foam below the heater is full cold insulating air which takes time to heat up. Technician is to communicate to the customer this condition is a normal operating characteristic of their vehicle. It will not impact the designed performance or reliability of the vehicle. Please share this information with the customer, including a copy of this message. |
| PIT3117J | 2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication provides information to the technician of part numbers that are missing from the service information documents. The following part numbers are for a cam nut that is available to adjust the rear toe 11519455, 11562237, 11570574. |
| PIT5422 | 2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication provides information to the technician for vehicles with an intermittent malfunction indicator lamp on, the interior lamps are inoperative and or the lift gate is inoperative. Diagnostic trouble codes U0078, U0140, U0151, U0155, U0164, U0198, or U0230 can be present. Inspect the body harness connector X901 for water intrusion or corrosion. Repair the connector and terminals as required. |
| PIP5209C | 2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication advises the technician to follow this Preliminary Information if there is a diagnostic trouble code P00C6 and or P228C set and normal Service Information diagnostics didn?t lead to a repair. Technician is to recheck the terminals at the Engine Control module for fit and tension as well as the crimp to the wire. The engine control module terminals to inspect are in the X2 connector. Inspect terminal number 3, 18 and 19 for the fuel rail pressure sensor and in the X3 connector terminals 16 and 32 for the high pressure fuel pump. The diagnostic trouble codes could set with as little as a 2 ohm resistance reading on these circuits. If any concerns are found replace the affected terminals and verify the repair. |
| PIT5076E | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication advises the technician to insure that global diagnostic service 2 diagnostic packages are up to date prior to learning the steering angle sensor for a diagnostic trouble code C710 symptom code 71 set in the electronic brake control module or the power steering control module. When rechecking for diagnostic trouble codes a U0074 U0077, U0180D, U01293, U0126, U0125, C0186, C0196, or C0287 are set and will not clear diagnose the Chassis bus. If no fault is found in the chassis bus check for an multiple diagnostic interface to data link connector issue. Technician is to try a different multiple diagnostic interface cable and attempt the steering angle sensor learn again following service information instruction then try to clear the codes again. |
| PIT5400 | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician for vehicles with a malfunction indicator lamp on, service stabilitrak, power steering or vehicle soon message displayed on the drivers information center. The technician may find the following diagnostic trouble codes U0073, U0100, U0101, U0121 U0140 C0045, C0050 in the body control module, electronic brake control module, engine control module, or the transmission control module. There may be multiple loss of communication codes current or history for high speed General Motors Local Area Network. Inspect the connections at connector X411 for corrosion due to the location of the connector under the vehicle by the rear wheel. |
| PIT5171D | 2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication provides information to the technician about vehicles that have may an intermittent Service Traction/Stability, ABS indicator or Service All wheel Drive message on the Driver Information Center. Technician may find Diagnostic Trouble Codes U0125 00 U0074 00 U0073 and or C0045 C0050 symptom 06. Technician will need to inspect the X411 connecter for a wire break inside the wire harness. Also inspect the wire harness insulation within 1 inch of the X411 before and after connecter. Repair any damaged wiring to correct the concern. |
| PIT4916D | 2017-08-15. Service bulletin. EQUIPMENT. This Preliminary Information communication provides information to the technician about vehicles that have may a helicopter type noise when a rear window is lowered. This is a normal characteristic of this vehicle, but the concern can be minimized by lowering a front door glass approximately 1 to 2 inches. |
| PIT4995D | 2017-08-15. Service bulletin. VISIBILITY/WIPER. This Preliminary Information communication provides information to the technician about vehicles with the rear wiper and/or the front rain sense wipers turn off when the vehicle is shifted to neutral. This is the normal operating characteristic of this vehicle. This is called Car Wash Mode. |
| PIT5399 | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable. |
| PIC4310L | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system. |
| PIP5282 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication advises the technician about the calculation and operation of the engine oil life monitor. The monitor calculates the percent of oil life remaining, based on 3 pathways. The first pathway for oil life calculation is engine revolutions. The second pathway for oil life calculation is the mileage form the last rest for all General Motors powertrains except the Volt. The third pathway for oil life calculation is the amount of time the oil is in the engine. The Volt uses a 2 year timer instead of 1 year. It also uses the engine revolution counter. It does not use the mileage pathway to count down. |
| PIP5122C | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technicians for diagnosing and repairing vehicles that have an issue with a pop noise from the fuel tank area after a cold start or Evaporative Emissions System purge. Technician will be able to use Global Diagnostic System 2 to duplicate the concern by commanding a purge and seal on the Evaporative Emissions System. Replacement of the auxiliary fuel pump module assembly will correct this concern. |
| PIT3046G | 2017-08-15. Service bulletin. FUEL SYSTEM, OTHER:STORAGE:FUEL GAUGE SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have an inaccurate fuel gauge. Technician should drive the vehicle to duplicate the concern. The fuel gauge will have a tendency to falsely indicate a lower fuel level than what is actually present. The fuel gauge will take a few minutes to show the correct fuel level. On vehicles equipped with an automatic transmission no buffering takes place when the transmission is in park or neutral. This is a normal characteristic and no repairs are necessary. On vehicles equipped with a manual transmission the fuel gauge is buffered in all gears and neutral. There is a timer which starts to count up when the clutch is depressed. When this timer reaches its calibrated value the buffering stops. This is a normal characteristic and no repairs are necessary. |
| PIC5953A | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact. |
| PIT5264C | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a "500 phone number" The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available. |
| PIP4548D | 2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. This Preliminary Information communication advises the technician what to inspect if codes P0016 and/or P0017 are setting on a properly timed engine or a condition of the vehicle cranks but will not start. Technician should inspect the respective intake or exhaust camshaft reluctor to see if it has spun on the camshaft. The reluctor cannot be repositioned so the camshaft must be replaced. The new camshafts come with the reluctor already pressed on in the correct position. |
| PIP5264 | 2017-08-15. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication provides information to the technician on the step to diagnose and repair vehicles that may have engine misfire and check engine light with any or all cylinder misfires only on deceleration. Technician will need to remove the accessory belts and drive or brake stall at signature RPM. If the concern is gone inspect for debris in the belt or pulleys causing a jump and false misfires. Also lift the engine to unload the engine mounts and test again. If concern is gone then inspect for a ground out concern with the mounts causing false misfires. |
| PIP5257 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses. |
| PIT3271G | 2017-08-15. Service bulletin. TIRES; WHEELS. This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection. |
| PIC3278F | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a "Phone Unavailable" audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A "Ready" or "OnStar ready" audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ?push to talk? button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern. |
| PIC4310K | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system. |
| 14-00-89-003A | 2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. This information for Warranty administration - Changes the Service Policy and Procedures Section 1.6.2.11 and now is refered to Article 3.2.9 of the 1st addition manual for details of Technician Identification and Accounting of Labor Time |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.