WenmarOpen by Wenmar Pro

Service bulletins for the 2013 Chevrolet Camaro

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

2042 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Brakes are shown. Show all

Bulletins, newest first
PIT4056H2018-01-22. Service bulletin. SERVICE BRAKES. This Preliminary Information communication provides information to the technician on the steps to help diagnose and repair vehicles with a Antilock Braking System Malfunction Indicator Lamp on. Technician will find the scan tool will not communicate with the Electronic Brake Control Module. Technician will check the Yaw and Lateral Accelerometer Sensor and the Steering Wheel Angle Sensor supply voltage circuit 2087 Dark Green shorted and pulling down the internal circuitry of the Electronic Brake Control Module. Not all vehicles use circuit 2087 to supply voltage to the Steering Wheel Angle Sensor, so be sure to check Service Information for the specific vehicle that is being serviced. If circuit 2087 is backed out of the EBCM connector and communication returns, inspect for either this circuit being shorted to ground or for a sensor concern. Technician will repair the circuit as necessary and reroute to prevent the concern from reoccurring. If the technician is working on a full-size or utilities that have aftermarket lift kits the wheel speed sensor may be broken or shorted. Technician will repair the circuit as necessary.
PI1360D2017-12-22. Service bulletin. PARKING BRAKE. This preliminary informational bulletin adds the 2015 Chevrolet Colorado and GMC Canyon to diagnosis and repair information to correct a customer concern of alleged no park, vehicle rolls in park or park will not hold.
17-NA-2392017-12-22. Service bulletin. PARKING BRAKE. This bulletin provides information on possible normal brake drag caused by sitting.
16-NA-2232017-12-22. Service bulletin. SERVICE BRAKES. This informational bulletin provides information on installing the correct tires for vehicles with the condition of under hard acceleration at higher speeds, the traction control light will flash. Or, they may come in for ABS or general handling/braking concerns.
PIC5214C2017-12-22. Service bulletin. SERVICE BRAKES; WHEELS. This Preliminary Information communication provides information to the technician about vehicles that may have wheels that are collecting an excessive amount of brake dust. Dealer should advised the customer that This is considered a normal characteristic.
16-NA-0592017-08-31. Service bulletin. SERVICE BRAKES, AIR:DISC:CALIPER; SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:CALIPER. This technical bulletin provides a procedure on how to properly clean the brake calipers without damaging the paint on them for concerns regarding staining/discoloring to the brake caliper paint
PIC5590B2017-08-15. Service bulletin. SERVICE BRAKES, HYDRAULIC. This Preliminary Information communication provides information to the technician about vehicles that exhibits a squeal noise. The front or rear brakes and typically are heard during slow stops. Dealer should communicate to the customer that these conditions are normal operating characteristics of their vehicle.
PIC61622017-08-15. Service bulletin. SERVICE BRAKES; EQUIPMENT. This Preliminary Information communication provides information to the technician about customers may inquire about a section in their owner's manual that addresses the use of high temperature brake fluid that should be used in their car during track use. Racing brake fluid has dry boiling points that are well above the specs of standard DOT 3 (401°) or DOT 4 (446°) brake fluid.
99-04-20-002I2017-08-15. Service bulletin. PARKING BRAKE:DRIVELINE. This informational bulletin explains a normal condition for what and how the drive line can clunk.
PIC6083B2017-08-15. Service bulletin. SERVICE BRAKES, AIR:DISC:PADS; SERVICE BRAKES, HYDRAULIC. This Preliminary Information communication provides information to the technician about vehicles that maynot move after being parked for extended period of time. This issue is due to the fact that the brake pads may have frozen to the vehicle's rotors. Technician should not replace any parts for this concern.
00-05-22-002O2017-08-15. Service bulletin. SERVICE BRAKES. This informational bulletin provides technicians with a brake lathe calibration procedure.
PI1360A2017-08-15. Service bulletin. PARKING BRAKE; PARKING BRAKE:DRIVELINE:HYDRAULIC:ACTUATOR. This preliminary informational bulletin provides diagnosis and repair information to correct a customer concern of alleged no park or vehicle rolls in park or park will not hold.
06-00-89-026L2017-08-15. Service bulletin. SERVICE BRAKES; EQUIPMENT:ELECTRICAL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER; POWER TRAIN:AXLE ASSEMBLY; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND.
PIC5428E2017-08-15. Service bulletin. SERVICE BRAKES; WHEELS; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have the Antilock Braking System, Service Traction Control System, and/or Service Stabilitrak lights are on. The Electronic Brake Control Module may have one or more of the following Diagnostic Trouble Codes C0035-C0050 with specifically symptom 18, 5A, or 0F. Technician will gain access to the correct wheel bear per the Diagnostic Trouble Code that is set. If debris is found on the magnetic encoder ring it will needed to be cleaned.
PIC5515C2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING; SERVICE BRAKES, HYDRAULIC; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have an intermittent ratchet, grind, or Antilock Braking System pump motor noises heard from the front of the vehicle when traveling in a straight line at slow speeds, usually under 20 mph. Technician should not replace the Electronic Brake Control Module or Brake Pressure Modulator Valve for this concern. Technician will need to review the Antilock Braking Data using Global Diagnostic System 2 while duplicating the concern. If three miles per hour or greater variance is detected in one or more data session logs, technician will need to inspect the wheel speed sensor and hub bearing with the variance.
PIC5590A2017-08-15. Service bulletin. SERVICE BRAKES, HYDRAULIC. This Preliminary Information communication provides information to the technician about vehicles that exhibits a squeal noise. The front or rear brakes and typically are heard during slow stops. Dealer should communicate to the customer that these conditions are normal operating characteristics of their vehicle.
PIC5428D2017-08-15. Service bulletin. SERVICE BRAKES; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have the Antilock Braking System, Service Traction Control System, and/or Service Stabilitrak lights are on. The Electronic Brake Control Module may have one or more of the following Diagnostic Trouble Codes C0035-C0050 with specifically symptom 18, 5A, or 0F. Technician will gain access to the correct wheel bear per the Diagnostic Trouble Code that is set. If debris is found on the magnetic encoder ring it will needed to be cleaned.
PIC5432C2017-08-15. Service bulletin. PARKING BRAKE; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have an intermittent Service Stabilitrak message being displayed in the Driver Information Center only at startup and that the message is gone within seconds of starting the engine. Technician will reprogram the Electronic Brake Control Module with the latest calibrations in Tis-2-Web.
PIC5137N2017-08-15. Service bulletin. EQUIPMENT:MECHANICAL; SERVICE BRAKES; EQUIPMENT:ELECTRICAL. This Preliminary Information communication advises the technician that the Electronic Brake Control Module and the Brake Pressure Modulator Valve parts restriction has ended. Dealer can now order the parts directly through your Parts Department without General Motors Technical Assistance Center authorization.
PIT4907A2017-08-15. Service bulletin. SERVICE BRAKES. This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and replacement parts from General Motors Service Parts Operations. Technician should be advised the costing should not be removed from the brake rotor it will wear off with normal brake usage. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
PIC5432D2017-08-15. Service bulletin. ELECTRICAL SYSTEM; SERVICE BRAKES, AIR:ANTILOCK:CONTROL UNIT/MODULE; SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:CONTROL UNIT/MODULE. This Preliminary Information communication provides information to the technician about vehicles that have an intermittent Service Stabilitrak message being displayed in the Driver Information Center only at startup and that the message is gone within seconds of starting the engine. On model year vehicles 2010 through 2012 technician will reprogram the Electronic Brake Control Module with the latest calibrations in Tis2Web.
PIC5214D2017-08-15. Service bulletin. WHEELS; SERVICE BRAKES. This Preliminary Information communication provides information to the technician about vehicles that may have wheels that are collecting an excessive amount of brake dust. Dealer should advised the customer that This is considered a normal characteristic.
PIC5428F2017-08-15. Service bulletin. SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP; SERVICE BRAKES, AIR:ANTILOCK; SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:CONTROL UNIT/MODULE; SERVICE BRAKES, AIR:ANTILOCK:CONTROL UNIT/MODULE. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have the Antilock Braking System, Service Traction Control System, and/or Service Stabilitrak lights are on. The Electronic Brake Control Module may have one or more of the following Diagnostic Trouble Codes C0035-C0050 with specifically symptom 18, 5A, or 0F. Technician will gain access to the correct wheel bear per the Diagnostic Trouble Code that is set. If debris is found on the magnetic encoder ring it will needed to be cleaned.
PIC5137P2017-08-15. Service bulletin. SERVICE BRAKES, ELECTRIC; SERVICE BRAKES, AIR:ANTILOCK:CONTROL UNIT/MODULE; SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DIFFERENTIAL PROPORTIONAL VALVE. This Preliminary Information communication advises the technician that the Electronic Brake Control Module and the Brake Pressure Modulator Valve parts restriction has ended. Dealer can now order the parts directly through your Parts Department without General Motors Technical Assistance Center authorization.
PIT4943C2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; FUEL SYSTEM, GASOLINE; SERVICE BRAKES, HYDRAULIC. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.