WenmarOpen by Wenmar Pro

Service bulletins for the 2012 Chevrolet Camaro

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

1893 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
PIP4786B2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that may have low oil pressure message. Technician may also find a Diagnostic Trouble Code P0521 in the Engine Control Module. Technician should follow all published Service Information diagnosis. When using a scan tool if the oil pressure is low but the oil pressure at the oil filter housing is correct, technician should inspect the Valve Lifter Oil Filter for debris/sludge that could be restricting oil flow to the oil pressure sensor. Technician should remove the Valve Lifter Oil Filter and clean it. If the Valve Lifter Oil Filter cannot be cleaned replace it.
PIC5491G2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
PIT54422017-08-15. Service bulletin. POWER TRAIN; EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician of an engine power reduced message on the driver information center after performing the Canada Onstar® 4G upgrade. If the concern is present park the vehicle outside and call General Motors Technical Assistance Center.
PIC5322D2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication advises the technician of a customer concern where the heated seat indicator light is not functioning or the heated seats are not up to operating temperature during a remote vehicle start event. This is normal operation of the heated seat during a remote vehicle start event. The electronic climate control module is not in a complete wake up state during a remote vehicle start mode and will not enable the light emitting diode. After a cold soak below 32 degrees Fahrenheit the seat will not get hot in the 10 minutes or less of the remote vehicle start mode. This is due to the fact that the heat element is not in direct contract with the seat surface while the seat is unoccupied and the foam below the heater is full cold insulating air which takes time to heat up. Technician is to communicate to the customer this condition is a normal operating characteristic of their vehicle. It will not impact the designed performance or reliability of the vehicle. Please share this information with the customer, including a copy of this message.
PIP5097A2017-08-15. Service bulletin. POWER TRAIN:AXLE ASSEMBLY. This Preliminary Information communication provides the technician with the following steps to correct a moan noise from the rear axle during cold turning maneuvers. This noise might start to be noticed as the vehicle accumulates over 3000 miles. The technician is to perform the following steps. 1. With original lube in axle, conduct Freeway Speeds for 10 miles to warm up lube. 2. Immediately drain original lube and refill with fresh lube. 3. In parking lot lock steering to the right, and then execute 5 Full Circles at (5-10 mph). 4. . In parking lot lock steering to the left, and then execute 5 Full Circles at (5-10 mph). 5. Perform 4 Figure 8?s at (5-10 mph). 6. Freeway Speeds for 20 miles until operating temperature is achieved. 7. In parking lot lock steering to the right, and then execute 5 Full Circles at (5-10 mph). 8. In parking lot lock steering to the left, and then execute 5 Full Circles at (5-10 mph). 9. Perform 4 Figure 8?s at (5-10 mph). 10. Immediately drain current lube in axle and refill with fresh lube. 11. Perform Steps 3 thru 9 again. 12. Immediately drain current lube in axle and refill with fresh lube. Proceed with steps 2 through 9 two times, for a total of 3 drain and fill procedures. This should only be done for a moan noise from the rear axle during cold start turning maneuvers. During regular maintenance the fluid only needs to be changed one time.
PIP4959E2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder. A customer may complain of misfires or roughness on cold start up with a P0300 diagnostic trouble code. Technician is to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. Dye is used to identify coolant over residual fuel being that might be left in the cylinder. The technician is not to replace the cylinder head as it will not correct this concern. In some cases it is necessary to remove the head for inspection. Do not replace the engine for small surface pock marks or a pitting appearance this is normal and do not connect to coolant passages. Usually if porosity is present there will be a break in the carbon ring. Only replace the engine if true porosity is found. Technician is to call Product Quality Center with the latest version of bulletin 02-07-30-029 if porosity is found and engine replacement is required.
PIP5209C2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication advises the technician to follow this Preliminary Information if there is a diagnostic trouble code P00C6 and or P228C set and normal Service Information diagnostics didn?t lead to a repair. Technician is to recheck the terminals at the Engine Control module for fit and tension as well as the crimp to the wire. The engine control module terminals to inspect are in the X2 connector. Inspect terminal number 3, 18 and 19 for the fuel rail pressure sensor and in the X3 connector terminals 16 and 32 for the high pressure fuel pump. The diagnostic trouble codes could set with as little as a 2 ohm resistance reading on these circuits. If any concerns are found replace the affected terminals and verify the repair.
PIT5076E2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication advises the technician to insure that global diagnostic service 2 diagnostic packages are up to date prior to learning the steering angle sensor for a diagnostic trouble code C710 symptom code 71 set in the electronic brake control module or the power steering control module. When rechecking for diagnostic trouble codes a U0074 U0077, U0180D, U01293, U0126, U0125, C0186, C0196, or C0287 are set and will not clear diagnose the Chassis bus. If no fault is found in the chassis bus check for an multiple diagnostic interface to data link connector issue. Technician is to try a different multiple diagnostic interface cable and attempt the steering angle sensor learn again following service information instruction then try to clear the codes again.
PIT53992017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
PIC4310L2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIP52822017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication advises the technician about the calculation and operation of the engine oil life monitor. The monitor calculates the percent of oil life remaining, based on 3 pathways. The first pathway for oil life calculation is engine revolutions. The second pathway for oil life calculation is the mileage form the last rest for all General Motors powertrains except the Volt. The third pathway for oil life calculation is the amount of time the oil is in the engine. The Volt uses a 2 year timer instead of 1 year. It also uses the engine revolution counter. It does not use the mileage pathway to count down.
PIP4786A2017-08-15. Service bulletin. FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY:PRESSURE RELIEF DEVICES. This Preliminary Information communication provides information to the technician about vehicles that may have low oil pressure message. Technician may also find a Diagnostic Trouble Code P0521 in the Engine Control Module. Technician should follow all published Service Information diagnosis. When using a scan tool if the oil pressure is low but the oil pressure at the oil filter housing is correct, technician should inspect the Valve Lifter Oil Filter for debris/sludge that could be restricting oil flow to the oil pressure sensor. Technician should remove the Valve Lifter Oil Filter and clean it. If the Valve Lifter Oil Filter cannot be cleaned replace it.
PIC5953A2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
PIP5168D2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published ?Engine Cranks But Does Not Run? diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly.
PIC60692017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician about vehicles that may have the side rails of a folding top not stowing completely. This is a normal characteristic for these vehicles, especially for ones with a new folding top.
PIC60662017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have rattle or buzz type noise that can be heard inside the passenger compartment while the vehicle is idling in drive or reverse. Technician should inspect the driver side engine mount using set of "chassis ears" or a piece of bulk spool heater hose. If the noise is coming from the mount replace it with part number 92249010
PIT5264C2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a "500 phone number" The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
PIP4554L2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides the technician with the steps on repairing a clunk noise after shifting from reverse to drive or drive to reverse and then accelerating. The concern is only with rear wheel drive 6L45 or 6L50 automatic transmissions with Regular Production Option Code MYA or MYB apply. Apply thread locker to the transmission output shaft flange splines and install a new front propeller shaft flange nut. Apply thread locker to the new propeller shaft flange nut if it does not contain a pre-applied adhesive patch.
PIP52642017-08-15. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication provides information to the technician on the step to diagnose and repair vehicles that may have engine misfire and check engine light with any or all cylinder misfires only on deceleration. Technician will need to remove the accessory belts and drive or brake stall at signature RPM. If the concern is gone inspect for debris in the belt or pulleys causing a jump and false misfires. Also lift the engine to unload the engine mounts and test again. If concern is gone then inspect for a ground out concern with the mounts causing false misfires.
PIP52572017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses.
PIP4568R2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.
PIT3271G2017-08-15. Service bulletin. TIRES; WHEELS. This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIC3278F2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a "Phone Unavailable" audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A "Ready" or "OnStar ready" audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ?push to talk? button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
PIC4310K2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PI0484B2017-08-15. Service bulletin. WHEELS:LUGS/NUTS/BOLTS/STUDS. This preliminary bulletin provides a procedure to paint the lug nut recess if the customer states that the paint looks thin.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.