Service bulletins for the 2012 Chevrolet Camaro
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1893 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Engine are shown. Show all
| 07-06-04-025L | 2017-08-31. Service bulletin. ENGINE. This informational bulletin provides information on Clicking/Ticking Sound/Noise Heard During Cold Start and that this should be considered a normal characteristic. |
|---|---|
| PIP5232B | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire. |
| PIP5216C | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair. |
| PIP5216B | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair. |
| PIC5295B | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE; FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY. This Preliminary Information communication provides information to the technician about vehicles that may have sloshing noise while stopping. Technician will need to add or remove 3 gallons of fuel in the fuel tank and retest. If the noise is gone after changing the fuel level then there is nothing you can do to change this condition. The noise is considered normal for that level of fuel in the tank. If the noise is present with all fuel levels, inspect for a blocked drain hole in the mufflers. Technician will need to clean out the drain hole to correct the concern. |
| PIP5276D | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on or a low oil pressure indicated after an oil change. Technician may find Diagnostic Trouble Code P0521. If Diagnostic Trouble Code P0521 setting in cold weather and it has a PF48E oil filter, change the filter to a UPF48R if one is available. |
| PIP5216A | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair. |
| PIP5276C | 2017-08-15. Service bulletin. ENGINE; EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on or a low oil pressure indicated after an oil change. Technician may find Diagnostic Trouble Code P0521. If Diagnostic Trouble Code P0521 setting in cold weather and it has a PF48E oil filter, change the filter to a PF48 if one is available. If there is no availability of oil filter PF48 use oil filter UPF48R. |
| PIP5257A | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses. |
| PIT4943D | 2017-08-15. Service bulletin. FUEL SYSTEM, GASOLINE; FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay. |
| PIP5216D | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair. |
| PIP3423M | 2017-08-15. Service bulletin. ENGINE; EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician that Diagnostic Trouble Codes P0016, P0017, P0018, P0019, P0008 or P0009 may be set. Technician will need to inspect for loose timing chains or tensioners. If after following Service Information diagnostics the root cause is not found inspect the reluctor for the crankshaft sensor. If the reluctor has moved then replace crankshaft. |
| PIP4919E | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicle that may have black smoke on a cold start. A dual-pulse injection strategy is utilized during engine cold start to reduce the time required to bring the catalytic converter up to operating temperature. This split injection strategy lasts for about 60 seconds on cold start. This process may cause the customer to see increased black smoke during cold start and should be considered normal. |
| PIP4750F | 2017-08-15. Service bulletin. ENGINE; EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician about vehicles that have a belt squeak noise and/or a crankshaft balancer appears to be out of balance or wobbling while watching it with the engine running. Technician will need to check crankshaft balancer run out. If the balancer run out is greater than 0.40mm, replace the crankshaft balancer. |
| PIP5095C | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil. |
| PIP4404F | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician vehicles with a slight rough idle. Technician should compare the concern with a like vehicle. If the concern is worse than a like vehicle, technician should follow published Service Information diagnosis and repair as necessary. |
| PIP5191A | 2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a ticking noise on cold start after sitting more than 6 hours. Technician will inspect the oil pump pick-up tube to block seal being compressed. It the seal is compressed replace the seal and retest. |
| PIP5163B | 2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; FUEL SYSTEM, GASOLINE; ENGINE. This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure. |
| PIP5209B | 2017-08-15. Service bulletin. ENGINE; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have Diagnostic Trouble Code P00C6 and/or P228C set. Technician will need to inspect the terminals at the Engine Control Module for fit and tension as well as the crimp to wire connection. Terminals to inspect in the ECM are connector x2 terminals 3, 18, and 19 for the fuel rail pressure sensor. Also connector x3 terminals 16 and 32 for the high pressure fuel pump. |
| PIP5029F | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed. |
| PIP4813C | 2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp, rough running, and/or lack of power. Technician may find Diagnostic Trouble Codes P0101, P0171, P0172, P0174, and/or P0175 set. Technician will need to inspect the hydrocarbon absorber pad that is on the inside of the air cleaner lid to ensure that it is properly secured to the lid. If the hydrocarbon absorber pad is found loose, technician will need to replace the air cleaner lid. |
| PIP5318 | 2017-08-15. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication provides information to the technician about vehicles that have a misfire event that usually occur at speeds of 70 miles per hour, 3rd Gear, and 3500 ? 4500 revolutions per minute. Dealer should advise customer to refer to TopTierFuel.com for availability in their respective area and fill with 91 or higher octane level fuel. |
| PIP5276E | 2017-08-15. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on or a low oil pressure indicated after an oil change. Technician may find Diagnostic Trouble Code P0521. Inspect the engine for any oil leaks and repair if need. Technician should change the engine oil and replace the oil filter using a PF48e type filter. |
| PIP4959E | 2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder. A customer may complain of misfires or roughness on cold start up with a P0300 diagnostic trouble code. Technician is to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. Dye is used to identify coolant over residual fuel being that might be left in the cylinder. The technician is not to replace the cylinder head as it will not correct this concern. In some cases it is necessary to remove the head for inspection. Do not replace the engine for small surface pock marks or a pitting appearance this is normal and do not connect to coolant passages. Usually if porosity is present there will be a break in the carbon ring. Only replace the engine if true porosity is found. Technician is to call Product Quality Center with the latest version of bulletin 02-07-30-029 if porosity is found and engine replacement is required. |
| PIP5282 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication advises the technician about the calculation and operation of the engine oil life monitor. The monitor calculates the percent of oil life remaining, based on 3 pathways. The first pathway for oil life calculation is engine revolutions. The second pathway for oil life calculation is the mileage form the last rest for all General Motors powertrains except the Volt. The third pathway for oil life calculation is the amount of time the oil is in the engine. The Volt uses a 2 year timer instead of 1 year. It also uses the engine revolution counter. It does not use the mileage pathway to count down. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.