WenmarOpen by Wenmar Pro

Service bulletins for the 2005 Chevrolet Blazer

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

486 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
01-07-30-042H2018-05-21. Service bulletin. POWER TRAIN:CLUTCH ASSEMBLY; POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER; POWER TRAIN. This information was created to inform the technician that the 2-3 upshift and the 3-2 downshift clunk is caused by the releasing of the 2-4 band and application of the 3-4 clutch assembly during an upshift. Also during a 3-2 downshift, the releasing of the 3-4 clutch during the application of the 2-4 band, can cause torque reversal down the output shaft creating a clunk. This is a normal condition.
080730035C2018-05-21. Service bulletin. POWER TRAIN. This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
09-07-30-018C2017-10-12. Service bulletin. POWER TRAIN; POWER TRAIN:AUTOMATIC TRANSMISSION. This warranty administration bulletin provides information on the change in automatic transmission add conditions documentation and claim submissions
02-07-30-052J2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN:AUTOMATIC TRANSMISSION:COOLING UNIT AND LINES. This informational bulletin provides technicians with information regarding automatic transmission oil cooler flow test essential tool J-45096 TransFlow®.
06-00-89-026L2017-08-15. Service bulletin. SERVICE BRAKES; EQUIPMENT:ELECTRICAL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER; POWER TRAIN:AXLE ASSEMBLY; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND.
PIP3720D2017-08-15. Service bulletin. POWER TRAIN:AXLE ASSEMBLY. This Preliminary Information communication provides information to the technician with the axel setup information from American Axle Manufacturing. Technician should be advised that the maximum pinion shim to be used or stacked behind the pinion is 0.050?, and the minimum pinion shim is 0.020? for an 8.6 axle. The range for available pinion depth shims for the 10.5? axle is 0.006? to 0.024?. When setting the backlash it should be set between 0.003? to 0.005? on a new ring and pinion for any American Axle Manufacturing application. The ring and pinion can be reused or adjusted if the mileage is less than 500 miles, if not used for towing. Technician should be advised that a ?roller coaster? or ?hourglass? pattern on the bearings may be normal up to 10,000 miles and possibly longer. With a mis-machined housing you may get a heel pattern on both sides of the gear teeth at build up can generally be corrected with backlash adjustments. When setting up an 8.6? axle with a 5 cut gear set is to use a 0.035? pinion shim and set backlash to 0.004?. When using the newer 2 cut gear set also use a 0.035? pinion shim and still set backlash to 0.004?. To set the gear pattern use backlash to adjust the pattern heel to toe. Use the pinion shim to adjust the height of the pattern. The proper drive pinion bearing pre-load is from 15 - 30 inch pounds with new bearings. The total torque to turn after the differential case is installed should increase 5 - 10 inch pounds at the pinion. A new pinion nut must be used whenever the old one is removed. The axle shaft end play specification is 0.012? per side and the radial specification is 0.002? - 0.003?. Technician should be advised that synthetic lube can be used in all new American Axle Manufacturing axle assemblies. The new pinion seal for the 8.6? axle assembly is a two piece design.
PIP-3366-B2012-02-29. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. CADILLAC/CHEVROLET/GMC/HUMMER: SOME SUVS AND TRUCKS ARE EXHIBITING A CONDITION WHERE BY GRINDING/RATCHETING TYPE NOISE COMING FROM AUTOMATIC TRANSMISSION WHEN SHIFTING INTO PARK WHILE IN 4WD LOW (4LO) RANGE. *PE
PIT-47222008-12-18. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:COOLING UNIT AND LINES. GMC: FLUID LEAK FROM TRANSMISSION OIL COOLER LINES DUE TO CORROSION. ALL 2000-2006 LIGHT DUTY TRUCKS EQUIPPED WITH THE LIGHT DUTY AUTOMATIC TRANSMISSION. *PE

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.