WenmarOpen by Wenmar Pro

Service bulletins for the 2008 Buick Enclave

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

1117 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
GCUS-9-10092018-05-07. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN. 14582A - Special Coverage (2012 model year Buick Enclave, Lacrosse, Regal; Chevrolet Traverse, and GMC Acadia vehicles have been removed). On some various model year vehicles, the throttle-position sensor may cause the engine to run rough, cause the malfunction-indicator lamp and/or an engine reduced power message to illuminate, and reduce the engine?s power. Dealers are to replace the throttle body assembly and gasket for Bosch equipped vehicles, or to install the throttle position sensor kit for Hitachi equipped vehicles. The Hitachi throttle body assembly only needs to be replaced if the sensor kit does not correct the condition. The repairs will be made at no charge to the customer. For vehicles covered by Vehicle Service Contracts, all eligible claims with repair orders on or after September 24, 2015, are covered by this special coverage and must be submitted using the labor operation codes provided with this bulletin. Claims with repair orders prior to September 24, 2015, must be submitted to the Service Contract provider.
PI09382018-04-23. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. This preliminary information bulletin provides information on powertrain and various electronic/electrical control issues.
13-08-116-001A2018-04-23. Service bulletin. TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS; POWER TRAIN; ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This technical bulletin provides a procedure on aftermarket ALSL or DLC devices causing multiple issues due to suspected tampering.
09-06-04-026G2018-04-23. Service bulletin. ENGINE; POWER TRAIN. This informational bulletin provides information of suspected tampering or vehicle modifications for non-GM (Aftermarket) engine and transmission calibrations for V6 and V8 gasoline engines Using Tech 2® or global diagnostic system 2 (GDS 2)
12-07-30-001B2018-04-16. Service bulletin. POWER TRAIN. This informational bulletin provides information for service agents not required to contact product quality center for CNG, LPG or gasoline engine, transmission and/or transfer case.
PI0620A2017-12-22. Service bulletin. POWER TRAIN; STEERING. This preliminary informational bulletin provides technicians diagnostic and repair information for GM recommending that the fluid be changed to DEXRON®-VI automatic transmission fluid when a steering gear assembly is replaced for any reason.
06-00-89-031C2017-12-22. Service bulletin. POWER TRAIN; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This informational bulletin provides information to dealership personnel on proper engine and automatic transmission/transaxle identification.
030729004I2017-12-22. Service bulletin. POWER TRAIN. This informational bulletin was created for the Manual Transmission Operating Characteristics. The different noises caused by driver habit, weather conditions , and normal manual transmission noises.
1203100022017-12-22. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER. This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles
GCUS-9-26352017-12-22. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. 14404B - Special Coverage.Bulletin. Some vehicles may experience a cracked or fractured transmission wave plate, resulting in a loss of 3rd, 5th and reverse gears. If this condition occurs within the stated terms dealers will repair the transmission.
PIP4112P2017-12-22. Service bulletin. ENGINE; POWER TRAIN. This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
PIP4653E2017-12-22. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicle that have a Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0601, P0603, P0604, P062F or P1621 stored in the Transmission Control Module. Technician will need to ensure that the Diagnostic Trouble Codes are set in the Transmission Control Module. If the Diagnostic Trouble Codes are only set in the Transmission Control Module reprogram the Transmission Control Module.
09-07-30-018C2017-10-12. Service bulletin. POWER TRAIN; POWER TRAIN:AUTOMATIC TRANSMISSION. This warranty administration bulletin provides information on the change in automatic transmission add conditions documentation and claim submissions
PI0746B2017-10-12. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; POWER TRAIN. This preliminary informational bulletin provides a procedure for the replacement of the camshaft cover for concerns relating to Malfunction Indicator Lamp (MIL) On, Poor Acceleration, Throttle Body Freezing, Multiple DTCs Set, Ice Deposits and/or Oil Deposits Present in Air Inlet Duct
PIT5165C2017-08-15. Service bulletin. POWER TRAIN; STEERING. This Preliminary Information communication provides information to the technician on the step to replace the power steering cooler. Technician will need to block off the hoses near the cooler connection with appropriate clamps. After the hoses are clamped disconnect the cooler from the lines and remove the cooler. Before installing the new cooler prefill the new cooler on the bench and cap off the pre-filled cooler ends for installation. When the new cooler is installed remove the clamps on the hoses and follow the service information for Power Steering System Bleed Procedure.
02-07-30-052J2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN:AUTOMATIC TRANSMISSION:COOLING UNIT AND LINES. This informational bulletin provides technicians with information regarding automatic transmission oil cooler flow test essential tool J-45096 TransFlow®.
06-00-89-026L2017-08-15. Service bulletin. SERVICE BRAKES; EQUIPMENT:ELECTRICAL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER; POWER TRAIN:AXLE ASSEMBLY; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND.
PIP4112M2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
PIP4112L2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
PIT4429D2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician about vehicles that may have a power lift-gate that is inoperative from all the switches and the keyless entry transmitter only with the ignition in the off position. Technician will need to check for battery voltage on circuit 5985 going to the Engine Control Module and to the Transmission Control Module.
PIP3720D2017-08-15. Service bulletin. POWER TRAIN:AXLE ASSEMBLY. This Preliminary Information communication provides information to the technician with the axel setup information from American Axle Manufacturing. Technician should be advised that the maximum pinion shim to be used or stacked behind the pinion is 0.050?, and the minimum pinion shim is 0.020? for an 8.6 axle. The range for available pinion depth shims for the 10.5? axle is 0.006? to 0.024?. When setting the backlash it should be set between 0.003? to 0.005? on a new ring and pinion for any American Axle Manufacturing application. The ring and pinion can be reused or adjusted if the mileage is less than 500 miles, if not used for towing. Technician should be advised that a ?roller coaster? or ?hourglass? pattern on the bearings may be normal up to 10,000 miles and possibly longer. With a mis-machined housing you may get a heel pattern on both sides of the gear teeth at build up can generally be corrected with backlash adjustments. When setting up an 8.6? axle with a 5 cut gear set is to use a 0.035? pinion shim and set backlash to 0.004?. When using the newer 2 cut gear set also use a 0.035? pinion shim and still set backlash to 0.004?. To set the gear pattern use backlash to adjust the pattern heel to toe. Use the pinion shim to adjust the height of the pattern. The proper drive pinion bearing pre-load is from 15 - 30 inch pounds with new bearings. The total torque to turn after the differential case is installed should increase 5 - 10 inch pounds at the pinion. A new pinion nut must be used whenever the old one is removed. The axle shaft end play specification is 0.012? per side and the radial specification is 0.002? - 0.003?. Technician should be advised that synthetic lube can be used in all new American Axle Manufacturing axle assemblies. The new pinion seal for the 8.6? axle assembly is a two piece design.
PIP4112N2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER. This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
PIT4214F2017-08-15. Service bulletin. POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicles that the Power Rear Lift-gate may reverse when closing. Technician will need to remove the lift-gate sill plate and cycle the power lift-gate closed to see if the concern still exists. If the concern is corrected, properly install the lift-gate sill plate. Technician will also need to inspect the lift-gate weather-strip seal for being fully installed on the body.
14404A2017-02-01. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. 14404A - SPECIAL COVERAGE (REVISED TO ADD MODEL YEAR VEHICLES, RPO CODES AND UPDATE WARRANTY TRANSACTION INFORMATION). SOME VEHICLES IDENTIFIED ABOVE AND, EQUIPPED WITH A 6T70 OR 6T75 - 6 SPEED FWD AUTOMATIC TRANSMISSION –– MAY EXPERIENCE A CRACKED OR FRACTURED WAVE PLATE, RESULTING IN A LOSS OF 3RD, 5TH AND REVERSE GEARS. DEALERS ARE TO REPLACE THE 3RD /5TH / REVERSE CLUTCH PLATE.
144042017-02-01. Service bulletin. ENGINE; POWER TRAIN:MANUAL TRANSMISSION. 14404 - SPECIAL COVERAGE. SOME VEHICLES IDENTIFIED ABOVE AND, EQUIPPED WITH A 6T70 OR 6T75 - 6 SPEED FWD AUTOMATIC TRANSMISSION –– MAY EXPERIENCE A CRACKED OR FRACTURED WAVE PLATE, RESULTING IN A LOSS OF 3RD, 5TH AND REVERSE GEARS. DEALERS ARE TO REPLACE THE 3RD /5TH / REVERSE CLUTCH PLATE.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.