Service bulletins for the 2009 BMW X6
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
248 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Engine are shown. Show all
| B123915 | 2018-11-13. Service bulletin. ELECTRICAL SYSTEM; ENGINE. Delivery Stop: Program Electronic Control Unit. A Delivery Stop has been issued on F15 PHEV vehicles produced from July 6, 2015 to October 21, 2015. These vehicles require programming of the Electric Machine Electronics (EME) Control Unit. The software will be available with ISTA/P 3.57.1 as of November 6, 2015. This bulletin will be updated with repair instructions and warranty information when it becomes available. Please contact your field representatives if you have any questions. |
|---|---|
| B123215 | 2018-11-13. Service bulletin. ELECTRICAL SYSTEM; ENGINE. "Engine Idle Speed Fluctuates Intermittently, when Shifting into Gear. While stationary, the engine idle speed could fluctuate (once or a few times) after engaging either ""Drive"" or ""Reverse gear. It is possible that the engine could also stall. This situation is intermittent, difficult to reproduce, and would not cause a fault to be stored. However, it is more likely to occur right after restarting a hot engine, A/C on, steering turned, and at ambient temperatures above 70° F. CAUSE DME software error (idle speed controller set point)." |
| B110815 | 2018-11-13. Service bulletin. ENGINE. ?N63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil. |
| B111614 | 2018-11-13. Service bulletin. ENGINE. "This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard. AFFECTED VEHICLES This Service Action applies to E70, E71, E72, F01, F02, F04, F07, F10, F12, and F13 vehicles with the N63 engines corresponding to the production dates listed above. First check if a Service Action label with a code number 728 is already attached to the B-pillar. If a code number 728 has already been punched out, the Campaign has already been performed and no further action is necessary. Eligible vehicles will show the following Service Action-related Campaign Code: 00 13 48 02 00 If the vehicle already has a label from a previous Service Action/Recall Campaign, affix the new label next to the old one. Do not affix one label on top of another one, because a number from an underlying label could appear in the punched-out hole of the new label." |
| B110715 | 2018-11-13. Service bulletin. ENGINE. "N63: Quality Control Monitoring After CCP. INFORMATION If the vehicle exhibits any of the above drivability issues, perform the ISTA/D N63 Misfire Detection test plan. Please make sure the FASTA data is transmitted. Submit a PuMA case titled ""N63: Drivability after CCP."" Follow the recommendations received." |
| 121015 | 2018-11-13. Service bulletin. EQUIPMENT; ENGINE. "SUBJECT N63: CBS Oil Service Conversion in ISTA/P. The CBS oil service conversion being performed for the N63 Customer Car Package and timing chain check (SI B11 16 14) does not work correctly. It does not change the interval to the desired 12 months/10,000 miles for the vehicles listed above in the specified production ranges. The ""Conversion, oil service 12months/15,000km/10,000 miles"" is working properly for all other N63 vehicles produced after these dates. Incorrect coding data in the current ISTA/P version" |
| 120415 | 2018-11-13. Service bulletin. ELECTRICAL SYSTEM; ENGINE. SUBJECT DME Internal and Valvetronic Faults Set at Cold Ambient Temperatures. The Service Engine Soon light (MIL) can be illuminated with the erroneous internal and Valvetronic faults stored in the DME. The MIL will only come on if the fault has been detected on two (or more) consecutive drive cycles. The following fault codes may be stored in the DME: E Seriesz 36AE - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 2DE2 - Valvetronic, actuation, voltage phase: Line disconnection z 2DE3 - Valvetronic, actuation, volt phase: Line disconnection z 2DE4 - Valvetronic, actuation, volt phase: Line disconnection F Seriesz 1F0905 - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 135B10 - Valvetronic, actuation, voltage phase: Line disconnection z 135B11 - Valvetronic, actuation, volt phase: Line disconnection z 135B12 - Valvetronic, actuation, volt phase: Line disconnection Engine performance and driving characteristics are not affected. DME software diagnostic sensitivity. |
| 110614 | 2018-11-13. Service bulletin. ENGINE; EQUIPMENT; EQUIPMENT:ELECTRICAL. "This Service Information bulletin and attachment supersedes SI B11 06 14 dated January 2015. designates changes to this revision SUBJECT N63 Engine: Customer Care Package. INFORMATION This bulletin outlines the Customer Care Package program that has been designed exclusively for BMW vehicles with the N63 engine. Vehicles with the N63 high performance engine are engineered with EfficientDynamics that provides fuel economy without compromising on its ""class leading"" power and performance. To ensure these engines keep delivering the ultimate performance, we have designed this Care Package that includes a 6 point check, and if necessary, the replacement of one or more of the following powertrain components: z Hot-Film Air Mass Sensors z PIEZO High Pressure Fuel Injectors z Engine Vacuum Pump z Fuel System Low Pressure Sensor/Feed Line z Fresh Air Intake Turbo Seals z Crankcase Ventilation Lines (Hoses) This engine care package also includes a multi-point inspection of the vehicle, including tire pressures, fluid levels, safety and convenience features. The N63CCP is NOT a mandatory Technical Campaign or Recall (per the authorities). It should only be completed based on parts availability, workshop capacity, and the customer's schedule. Complete all other applicable open Campaigns per the DCS Warranty inquiry and the Key Reader. Perform all recommended, due or qualifying ""time-based"" maintenance service task items as directed by the Key Reader/ISPA Light application. When eligible, also perform the procedure described in SI B61 30 14: 12-Volt Battery Replacement together with performing the N63 Customer Care Package. After completing all the necessary repairs, the vehicle needs to be road tested for 30 minutes to assure the highest standard of performed repairs (Please see ""Warranty Information"" section below)." |
| B121015 | 2018-11-05. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; ENGINE. N63: CBS Oil Service Conversion in ISTA/P. The CBS oil service conversion (8KL) performed for the N63 Customer Car Package and timing chain check (SI B11 16 14) did not work correctly for the above models with previous versions of ISTA/P. After the conversion, the forecast interval did not change to the desired 10,000 miles/12 months, or the forecast is displayed as an invalid value, for example: 25,000 miles/24 months. 1. Incorrect DME coding or calibration data 2. The ISTA CBS correction test plan contains an error when attempting to correct an invalid oil service prognosis value. |
| B111614 | 2018-11-05. Service bulletin. ENGINE. "This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard." |
| B110815 | 2018-11-05. Service bulletin. ENGINE. N63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. ? B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs ? B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints ? B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity ? B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. ? Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine ? Excessive engine oil consumption ? Spark plugs fouled with engine oil |
| 111614 | 2018-11-05. Service bulletin. ENGINE. "This Service Information bulletin and attachment supersedes SI B11 16 14 dated January 2015. designates changes to this revision SUBJECT N63 Engine: Check the Timing Chain. INFORMATION This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard." |
| B130815 | 2018-11-05. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS. Service Action: S63 Engine - Check and Replace High- Pressure Injectors This Service Information bulletin supersedes SI B13 08 15 dated January 2016. The high-pressure injectors may fail, resulting in an engine malfunction warning and reduced engine output. |
| B110815 | 2018-11-05. Service bulletin. ENGINE. N63 and S63 Engine: Valve Seal Replacement This Service Information bulletin replaces SI B11 08 15 June May 2017 What's New: Diagnostic tips updated. Refer to the following applicable SIBs before replacing the valve seals. B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repair B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine in addition to excessive engine oil consumption Spark plugs fouled with engine oil and excessive engine oil consumption Excessive engine oil consumption Vehicles with less than 40,000 miles should not be considered for valve seal replacement. All Vehicles: A complete oil consumption test, as described inSI B11 03 13, must be performed first, before replacing the valve seals. Do not remove the intake manifolds to clean the intake valve carbon. |
| B130315 | 2018-11-05. Service bulletin. ENGINE AND ENGINE COOLING. N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error What's New: ? Procedure change: indentifying injector type using an ISTA test plan. . The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number. |
| B111715 | 2018-11-05. Service bulletin. EQUIPMENT; ENGINE. "?N63, N63TU, N63R, S63 AND S63TU ENGINES: UPPER OIL PAN REMOVAL AND INSTALLATION REPAIR INSTRUCTIONS This Service Information bulletin supersedes SI B11 17 15 dated October 2016. . INFORMATION When removing and/or installing the engine upper oil pan assembly, the oil pan can sustain damage if this operation is not performed correctly. Before loosening or tightening the engine upper oil pan refer to the newly released Repair Instruction 11 13 010 ""Removing and installing/replacing upper oil sump"" in ISTA/D 3.55.2 or higher for the proper procedures. IMPORTANT: The new repair instructions will state one of the following before reinstalling the upper engine oil pan. ""All threads must be cleaned with screw tap"" Or ""Clean all threads with screw tap. Order number 81 43 0 402 559"" Or ""Clean all threads with a thread cutter"". The current repair instruction terminology will be modified to include this information." |
| B110115 | 2018-04-23. Service bulletin. ENGINE. Engine Oil Quick Reference Chart and Drain Plug Torque: The current version of ISTA/D has an error in the engine oil capacity specification for all vehicles with the N63R engine and xDrive. |
| SIB-11-16-14 | 2015-05-20. Service bulletin. ENGINE. BMW: ON CERTAIN VEHICLES, ENGINE TIMING CHAIN SHOULD BE CHECKED FOR EARLY STAGES OF WEAR, AND A REPAIR SOLUTION SHOULD BE PROVIDED. *PE UPDATED 9/25/15. *PE UPDATED 10/6/15. *PE |
| SIB-01-02-12 | 2013-08-21. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER. BMW: ON CERTAIN VEHICLES, AN EMISSIONS WARRANTY HAS BEEN EXTENDED TO 8 YEARS/82,00 MILES ON ENGINE TURBOCHARGER WASTEGATE. MODELS 2008-2010 E60, E61, E71, E82, E88, AND 2009-2010 E89, AND 2007-2010 E90, E92, E93. *PE |
| SIB-16-07-12 | 2012-11-01. Service bulletin. ENGINE; FUEL SYSTEM, OTHER:STORAGE:FUEL GAUGE SYSTEM. BMW: FUEL GAUGE SHOWS 3/4 FULL AFTER REFUELING DUE TO INTERNAL MECHANISMS OF FUEL LEVEL SENSORS, WITH A HIGH PROPORTION OF ETHANOL, SWELLING AND INHIBIT, ONE OR BOTH, MOVEMENT OF FUEL LEVEL SENSORS. MODEL 2007-2009 E70, E71. *PE UPDATED 1/15/13. *PE |
| SIB-11-08-12 | 2012-11-01. Service bulletin. ENGINE. BMW: DUE TO DAMAGED SEAL RING, DURING ASSEMBLY, ENGINE OIL IS LEAKING FROM ENGINE OIL PUMP VOLUME CONTROL VALVE GASKET SEAL RING. MODELS E70, E71, F01, F02, F04, F07, F10, F12, F13. NO MODEL YEARS LISTED. *PE |
| SIB-12-14-12 | 2012-08-27. Service bulletin. ENGINE. BMW: EXPERIENCING LOSS OF ENGINE POWER, SERVICE ENGINE SOON LAMP IS ILLUMINATED, A NOISE, LIKE RATTLING, COMING FROM ENGINE COMPARTMENT. *PE UPDATED 10/31/12. *PE MODELS 2010 E70, 71, 82, 88, 90, 92, 93, F07, 10, 12, 13, 25. UPDATED 1/18/13. *PE UPDATED 4/18/2013. *KB UPDATED 05/13/2013 *JS UPDATED 5/19/15. *PE |
| SIB-11-07-12 | 2012-08-27. Service bulletin. ENGINE. BMW: WHILE DRIVING VEHICLE, AT TIMES WOULD BE ROUGH RUNNING; WHITE OR BLUE SMOKE SEEN EXITING EXHAUST SYSTEM AND THE ENGINE OIL IS CONSUMED ABOVE SPECIFICATIONS. *PE UPDATED 1/11/13. *PE |
| SIB-01-02-12 | 2012-08-27. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. BMW: A FAILURE OF THE TURBOCHARGER WASTEGATES, CAUSED BY A DEFECT, HAS AN EMISSIONS EXTENDED WARRANTY, 8 YEARS OR 82,000 MILES, WHICHEVER COMES FIRST, NOT OTHERWISE FALLING WITHIN COVERAGE EXCLUSION. *PE |
| SIB-13-13-10 | 2012-01-06. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. BMW: ON SOME VEHICLES, THE HIGH PRESSURE FUEL PUMP HAS AN INTERNAL COMPONENT THAT MAY FAIL AND CAUSING DRIVABILITY SYMPTOMS SUCH AS ERRATIC ENGINE OPERATION AND LONGER STARTING TIMES. *PE |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.