WenmarOpen by Wenmar Pro

Service bulletins for the 2017 BMW X5

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

300 on file from NHTSA, as of 2026-10-19.

By type

By component

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
B1228182019-02-25. Service bulletin. ENGINE. MALFUNCTION INDICATOR LAMP (MIL) MULTIPLE MOTOR POSITION SENSOR FAULTS STORED IN EME.
B1107162018-12-10. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE; ENGINE. Diesel Engine: Intake Manifold Damaged. The Service Engine Soon light is on. There may also be: Complaints of lack of engine performance An exhaust smell coming from the engine area. The following fault codes may be stored in the DDE: 24CE00 - Hot film air mass meter: Ratio of measured to calculated air mass too high 27F000 - Charge air hose monitoring in idle: Charge air hose fallen down 290900 - Air system, air to EGR air mass flow plausibility: Measured air mass compared to calculated air mass too high 290A00 - Air system, air to EGR air mass flow plausibility: measured air mass compared to calculated air mass too high and high charging pressure control deviation 1. Excessive thermal load from the EGR system on the intake components 2. An excessive or unmetered air leak in the intake/charge air system
B6208162018-12-10. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE. Incomplete AdBlue Check Control Message (CCM) on the Central Information Display. An incorrectly displayed AdBlue (Diesel Exhaust Fluid refill range) CCM is shown on the Central Information Display. Improper instrument cluster software
B1117152018-12-10. Service bulletin. ENGINE; EQUIPMENT. "N63, N63TU and N63R Engines: Upper Oil Pan Removal and Installation Repair Instructions This Service Information bulletin supersedes SI B11 17 15 dated August 2015.. INFORMATION When removing and/or installing the engine upper oil pan assembly, the oil pan can sustain damage if this operation is not performed correctly. Before loosening or tightening the engine upper oil pan refer to the newly released Repair Instruction 11 13 010 ""Removing and installing/replacing upper oil sump"" in ISTA/D 3.55.11 or higher for the proper procedures. IMPORTANT: The new repair instructions will state one of the following before reinstalling the upper engine oil pan. ""All threads must be cleaned with screw tap"" Or ""Clean all threads with screw tap. Order number 81 43 0 402 559"" Or ""Clean all threads with a thread cutter"". The current repair instruction terminology will be modified to include this information."
B1301162018-12-10. Service bulletin. FUEL SYSTEM, DIESEL; ELECTRICAL SYSTEM:SOFTWARE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE); ENGINE AND ENGINE COOLING:ENGINE:DIESEL. The DDE software application for exhaust gas recirculation control (EGR) does not favorably match the diesel fuel grades available in many parts of the US market. The high pressure EGR cooler could become filled with soot particulate to the point that exhaust gas flow and cooling efficiency are significantly reduced. This could result in the Service Engine Soon light coming on with EGR control / Air mass faults being stored in the DDE.
B1201162018-12-10. Service bulletin. ELECTRICAL SYSTEM; ENGINE. Under certain engine operating conditions the measured air mass between the cylinder banks 1-4 and 5-8 is miscalculated by the DME's. This could result in incorrect engine torque and mismatched ignition parameters with the possibility of internal engine damage.
B1111172018-12-03. Service bulletin. ENGINE. ?ENGINE LEAK DIAGNOSIS ON TURBOCHARGED V8 ENGINES. When diagnosing an engine oil leak or a coolant leak on turbocharged V8 engines it is necessary to use a borescope to identify if the source of the leak is from under the turbochargers. Engine oil or coolant leaking from the bell housing area or the front timing chain cover area may be caused by the turbocharger itself, a turbocharger oil/coolant feed line or turbocharger oil/coolant return line. Do not remove the transmission and do not dissemble the engine before performing this inspection. If necessary, use engine oil leakage detection dye.
B1101132018-11-26. Service bulletin. ENGINE. N63 AND N63T ENGINE: ENGINE OIL CONSUMPTION, ENGINE OIL TOP-UPS AND REFILL CAPACITY. Customers with one of the vehicles above may complain that the engine's oil consumption is "too high," resulting in engine oil top-ups and workshop visits to address the issue before the vehicle displays an engine oil service as being "due." When the vehicle's engine oil drops to the minimum level, a message will display in the vehicle advising the driver to "add 1 quart of engine oil." After topping up and continued operation, the "add engine oil" message may display again before an engine oil service is required and performed. CAUSE Engines that are fitted with a turbocharger, as part of their normal operation, will consume engine oil at a higher rate than a naturally aspirated engine (non-turbocharged engine). In this case, a "turbocharged" engine could require topping up of the engine oil more frequently.
B6403182018-11-26. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT:APPLIANCE:AIR CONDITIONER. DELIVERY STOP: REFRIGERANT AIR CONDITIONING. An incorrect refrigerant was used to fill the refrigerant circuit in the affected vehicles after assembly. AFFECTED VEHICLES This Service Action involves X5 or X6 (Only 8 vehicles) vehicles produced from January 16 to February 19, 2018. Vehicles which require this Service Action to be completed will show it as "Open" when checked either in AIR, the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader. The affected vehicles will be identified with the description: 0064950100 B640318 Delivery Stop: Refrigerant Air Conditioning.
B1609182018-11-26. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL. SCR SYSTEM FAULT 805256 STORED IN VERY COLD WEATHER. After the vehicle is exposed to prolonged temperatures under -9°C (15.8°F) and is then driven a long distance when temperatures are above -9°C (15.8°F), the check engine light may be illuminated. The following fault may be stored in the Digital Diesel Electronics (DDE) 805256 - Active tank filling level sensor, signal: echo fault In low temperature under -9°C (15.8°F) a layer of ice may form in the active tank. This can result in an incorrect level measurement after the vehicle is driven.
B6108172018-11-26. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. ?General Electrical Systems Technical Service. VOLUNTARY EMISSIONS RECALL CAMPAIGN 17E-A01: CHECK CHARGING OF THE HIGH VOLTAGE BATTERY Bulletin type was changed from a Service Action to an Emissions Recall. High-voltage charging system may not work correctly. Alternative Mobility Solutions (AMS) Reimbursement This BMW Service Action repair qualifies for Alternative Mobility Solution (AMS) expense reimbursement. Please refer to SI B01 29 16 for claim submission details. Intermittent hardware failure of the charging module (KLE).
B1208172018-11-26. Service bulletin. POWER TRAIN; ENGINE. POWERTRAIN FAULTS DUE TO CHAFING OF ENGINE WIRING HARNESS. One or more of the following fault codes are stored in the DDE: 29FB00 - DeNOx system, warning and switching off scenario: Warning level 1 280D00 - NOx-Sensor upstream DeNOx-catalytic converter, signal NOx: NOx-Signal invalid for too long 280F00 - NOx-Sensor downstream DeNOx-catalytic converter, signal NOx: NOx-signal invalid for too long 29FC00 - DeNOx-system, warning and switch-off scenario: Warning level 2 CD840A - FA-CAN bus: Control unit switched off from bus (Bus off) CD94C7 - Message (RQ_PWR_EL_EPS, 234.0.2, FX): Messaging from EPS failed CD951C - Message (AVL_STMOM_DV_ACT_AVL_FORC_GRD, 49.0.2, FX):Messaging from EPS failed CD9536 - Message (DIAG_OBD_SCR, 0x3EE, FA): Messaging from SCR control unit failed CD953A - Message (ST_FFLV_SCRA, 0x40B, FA): Messaging from SCR control unit failed CD953C - Message (ST_RESO_SCRA, 0x8A, FA): Messaging from SCR control unit failed CD942B - Message (DT_GRDT, 0x1AF, A): Messaging from transmission control unit failed CD946B - Message (ST_GRB_ECU, 0x39A, FA): Messaging from transmission control unit failed CD9487 - Message (RQ_TORQ_CRSH_GRB, 0xB0, A): Messaging from transmission control unit failed CD94B9 - Message (DISP_RPM_ENG_DYNS, 0xF8, A): Signal(s) in message invalid CD94BA - Message (DISP_RPM_ENG_DYNS, 0xF8, A): Messaging from transmission control unit failed CD94C3 - Message (DIAG_OBD_GRB, 0x396, FA): Messaging from transmission control unit failed CD94DC - Transmission control unit, communication: Transmission communication via A- CAN and FACAN failed CD94ED - Message (DT_DISP_GRDT, 0x3FD, FA): Messaging from transmission control unit failed CD950D - Message (RQ_TORQ_CRSH_GRB_2, 0xA0, A): Signal(s) in message invalid ? CD950F - Message (RQ_TORQ_CRSH_GRB_2, 0xA0, A): Messaging from transmission control unit failed ? CD9549 - Message (DIENSTE-ID2=19 request MSA function, 0x598, FA): Message from transmitter control unit (EGS_EL) failed.
B5116152018-11-05. Service bulletin. EQUIPMENT:OTHER:LABELS; ENGINE. "Delivery Stop: Remove Engine Oil Label. Affected vehicles in dealer inventory must not be retailed or delivered until the label is removed. Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a ""Vehicle Comment"" in the DCS Warranty Vehicle Inquiry or ISPA Light. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/248...9/3/2016 Page 2 of 2"
B1107162018-11-05. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. Diesel Engine: Intake Manifold Damaged This Service Information bulletin supersedes SI 11 07 16 dated May 2016. The Service Engine Soon light is on. There may also be: Complaints of lack of engine performance An exhaust smell coming from the engine area. The following fault codes may be stored in the DDE: 24CE00 - Hot film air mass meter: Ratio of measured to calculated air mass too high 27F000 - Charge air hose monitoring in idle: Charge air hose fallen down 290900 - Air system, air to EGR air mass flow plausibility: Measured air mass compared to calculated air mass too high 290A00 - Air system, air to EGR air mass flow plausibility: measured air mass compared to calculated air mass too high and high charging pressure control deviation 1. Excessive thermal load from the EGR system on the intake components 2. An excessive or unmetered air leak in the intake/charge air system
B6621162018-11-05. Service bulletin. ENGINE; LANE DEPARTURE: SENSING SYSTEM: OTHER; SERVICE BRAKES. KAFAS CAMERA-BASED ASSISTANCE SYSTEM LIMITS. INFORMATION The situations described above may all be caused by known limitations of the system such as: Dirty windshield Incomplete calibration process Unsuccessful calibration Restricted visibility- weather conditions or parked vehicles Missing lamps on target vehicle Non-standard vehicle exterior surfaces Insufficient ambient lighting Abrupt motion of target vehicle.
B1803162018-11-05. Service bulletin. ENGINE AND ENGINE COOLING. DDE FAULT CODE: 28DE00 - EXHAUST GAS PRESSURE SENSOR BEFORE TURBINE, PLAUSIBILITY. After performing repairs where the engine harness was disconnected and reconnected at the differential pressure and the exhaust pressure sensor, the following fault is then stored in the DDE: 28DE00 - Exhaust gas pressure sensor before Turbine, plausibility: exhaust gas pressure in front of turbine dynamically not plausible
B1218162018-11-05. Service bulletin. ENGINE. CHECK CONTROL MESSAGE: NO OIL PRESSURE. Check Control message: Oil pressure warning. Stop carefully is displayed. There are no related faults to oil pressure stored in the DDE. Unfavorable DDE software application When operating during automatic engine start-stop function stop, it may be the case that the oil pressure is incorrectly determined to be too low, which triggers a CC message.
B6128172018-11-05. Service bulletin. ENGINE AND ENGINE COOLING. "SME FAULT CODE 21F04B. One or several of the following check control messages (CCM) may be displayed: ""Engine fault! Power loss"" (CCM-ID: 29) ""Powertrain malfunction!"" (CCM-ID: 633) ""Hybrid system malfunctioning!"" (CCM-ID: 585) Note: The fault code 21F04B stated below may also be entered without any of the above mentioned CC messages being displayed A timing problem between the SME and the cell supervision circuit (CSC)."
B1303152018-11-05. Service bulletin. ENGINE AND ENGINE COOLING. N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error What's New: ? Procedure change: indentifying injector type using an ISTA test plan. . The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.
B1803102018-11-05. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. "? NO REGENERATION OF THE DIESEL PARTICULATE FILTER (DPF) This Service Information bulletin supersedes SI B18 03 10 dated November 2010. . The Service Engine Soon lamp is illuminated. The following fault codes may be stored in the DDE: N47T/N57T engine 245700 - Particle filter system: particulate filter highly loaded (Exhaust backpressure high) 245800 - particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) M57Y engine 480A Particle filter system - filter is heavily contaminated. (exhaust backpressure is too high) 481A Particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) CAUSE 1. Faults with the exhaust system that affect the monitoring of the DPF by the DDE 2. Unfavorable recent driving profile INFORMATIOM During normal driving, there is a continuous regeneration of the diesel particulate filter that takes place at exhaust-gas temperatures between 280 and 350°C (slower oxidation process). The soot particles can only be burned off when the required exhaust-gas temperature has been reached. Under certain driving conditions (i.e., prolonged short trips or an exhaust system which never reaches soot burn-off temperatures), the DPF can become restricted. The DDE will initiate periodic regeneration automatically, at the latest after 600 miles. In vehicles making many short distance journeys, periodic regeneration takes place after only 250-500 miles. The Digital Diesel Electronics control unit evaluates the time for periodic regeneration from the following values: average distance driven average driving speed temperature in the diesel particulate filter values from the exhaust pressure sensor The DDE initiates the regeneration process by decreasing incoming air by the throttle valve, and one or two post injections are executed. This heats the exhaust-gas temperature to approx. 600° C . When the exhaust temp reaches this point: The soot is burned off with the residual oxygen. The
B1801172018-11-05. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE. "? DIESEL PARTICULATE FILTER (DPF) CLEANING . The following performance issues may be noticed by the customer: CC-Message ""Drive faulty"" Engine jerking or a lack of power over the whole engine speed range Malfunction indicator lamp (MIL) is illuminated The following fault codes may be stored in the DDE: N47T/N57T engine Main Faults: 245700 - Particle filter system: particulate filter highly loaded (Exhaust backpressure high) 258300 - Exhaust backpressure sensor, Signal: Signal too high Secondary Faults: 244C00 - Charging pressure control, control deviation: charging pressure too low/positive deviation 25DA00 - Exhaust gas difference pressure sensor particle filter, Signal: short circuit to plus pole M57Y engine Main Faults: 480A particle filter system 481A particle filter system Secondary Faults: 4530 charging pressure control, control deviation 429A charging pressure control low pressure stage, control deviation Clogged DPF."
B1227162018-11-05. Service bulletin. ENGINE; ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:12V/24V/48V BATTERY. "? DIAGNOSING NON FUNCTIONING ""eDRIVE"" This Service Information bulletin supersedes SI B12 27 16 dated November 2016. The customer complains that the vehicle will not go into ""eDrive"", and in some cases ""eDrive"" is greyed-out in the control display (CID) and is not selectable. Also, there are no pertinent electric drivetrain fault codes that assist with diagnosis. Possible 12 volt battery failure, Intelligent Battery Sensor (IBS) failure or MSA deactivation."
B1121162018-11-05. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE. "?CCM: ""START/STOP FAILED"": LOSS OF POWER . Malfunction Indicator Lamp (MIL) is illuminated Check Control Message (CCM) states ""Auto Start/Stop function failed"" One or more of the following codes may be stored in the DME fault memory' 120408: ""Charging pressure control: switching off as a subsequent reaction"" 130F20: ""Exhaust camshaft: angular offset to crankshaft outside of tolerance"" 130E20: ""Intake camshaft: angular offset to crankshaft outside of tolerance"" 164040: ""Intake camshaft: Installation faulty"" 164041: ""Exhaust camshaft: Installation faulty"" Incorrect camshafts timing position (in reference to crankshaft). Combustions occurring just as engine is stopping, drive the engine backwards, dragging the belt drive and toothed belt starter motor backwards. High-inertia torque loading on the camshaft sprockets and crankshaft at this point causes slippage, unintentionally adjusting the timing."
B1117152018-11-05. Service bulletin. EQUIPMENT; ENGINE. "?N63, N63TU, N63R, S63 AND S63TU ENGINES: UPPER OIL PAN REMOVAL AND INSTALLATION REPAIR INSTRUCTIONS This Service Information bulletin supersedes SI B11 17 15 dated October 2016. . INFORMATION When removing and/or installing the engine upper oil pan assembly, the oil pan can sustain damage if this operation is not performed correctly. Before loosening or tightening the engine upper oil pan refer to the newly released Repair Instruction 11 13 010 ""Removing and installing/replacing upper oil sump"" in ISTA/D 3.55.2 or higher for the proper procedures. IMPORTANT: The new repair instructions will state one of the following before reinstalling the upper engine oil pan. ""All threads must be cleaned with screw tap"" Or ""Clean all threads with screw tap. Order number 81 43 0 402 559"" Or ""Clean all threads with a thread cutter"". The current repair instruction terminology will be modified to include this information."
B1101172018-11-05. Service bulletin. ENGINE. ?N63T AND S63T ENGINE: VALVE SEAL REPLACEMENT . This SI provides a new tool and a new procedure for the N63TU valve seals replacement. Please refer to the following applicable SIBs before replacing the valve seals. SI B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs SI B11 01 13 - N63 and N63TU Engines: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity SI B11 03 13 - Engine Oil Consumption (all models) SI B11 04 13 - N63TU Engine: Engine Oil Consumption If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.