Service bulletins for the 2011 BMW R 1200 GS
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
174 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Engine are shown. Show all
| B111614 | 2018-11-13. Service bulletin. ENGINE. "This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard. AFFECTED VEHICLES This Service Action applies to E70, E71, E72, F01, F02, F04, F07, F10, F12, and F13 vehicles with the N63 engines corresponding to the production dates listed above. First check if a Service Action label with a code number 728 is already attached to the B-pillar. If a code number 728 has already been punched out, the Campaign has already been performed and no further action is necessary. Eligible vehicles will show the following Service Action-related Campaign Code: 00 13 48 02 00 If the vehicle already has a label from a previous Service Action/Recall Campaign, affix the new label next to the old one. Do not affix one label on top of another one, because a number from an underlying label could appear in the punched-out hole of the new label." |
|---|---|
| B121016 | 2018-11-13. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. "N63T - Drivetrain Malfunction Message after Driving for Several Hours This Service Information bulletin supersedes SI B12 10 16 dated April 2016. ""Drivetrain Malfunction"" message displayed with reduced engine power. Erroneous misfire faults may be stored for cylinders 3 and 6. The situation is most likely to occur after driving for several hours at constant highway speeds with light throttle (low load and low engine speed). Cycling ignition off and back on again clears the ""Drivetrain Malfunction"" warning DME software (plausibility check error)." |
| 111614 | 2018-11-05. Service bulletin. ENGINE. "This Service Information bulletin and attachment supersedes SI B11 16 14 dated January 2015. designates changes to this revision SUBJECT N63 Engine: Check the Timing Chain. INFORMATION This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard." |
| B110815 | 2018-11-05. Service bulletin. ENGINE. N63 and S63 Engine: Valve Seal Replacement This Service Information bulletin replaces SI B11 08 15 June May 2017 What's New: Diagnostic tips updated. Refer to the following applicable SIBs before replacing the valve seals. B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repair B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine in addition to excessive engine oil consumption Spark plugs fouled with engine oil and excessive engine oil consumption Excessive engine oil consumption Vehicles with less than 40,000 miles should not be considered for valve seal replacement. All Vehicles: A complete oil consumption test, as described inSI B11 03 13, must be performed first, before replacing the valve seals. Do not remove the intake manifolds to clean the intake valve carbon. |
| B130315 | 2018-11-05. Service bulletin. ENGINE AND ENGINE COOLING. N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error What's New: ? Procedure change: indentifying injector type using an ISTA test plan. . The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number. |
| B111216 | 2018-11-05. Service bulletin. ENGINE AND ENGINE COOLING. ?SERVICE ACTION: SERVICE ACTION: N63T ENGINE CHECK AND REPLACE THE CRANKCASE VENTILATION HOSES What's New: ? Defect Code format updated ? Consequential Additional Repair(s) statement added ? Overlapping Labor Procedure statement added . The crankcase ventilation hoses may become brittle and break when they come in contact with hot engine components. One or more of the crankcase ventilation hoses are not FPM rubber material. The FPM rubber material is engine heat resistant. Or The plastic coggurated hoses are not fitted with the self-locking spacers. The self-locking spacers maintain an air gap between the hoses and the hot engine components. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.