WenmarOpen by Wenmar Pro

Service bulletins for the 2020 BMW i3

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

40 on file from NHTSA, as of 2026-10-19.

By type

By component

Bulletins, newest first
B5118152020-06-15. Service bulletin. SEAT BELTS. A Check Control Message is displayed for the Tailgate Lock Open: A Check Control Message is displayed indicating that the tailgate is open even though it is mechanically closed. Faulty tailgate lock or incorrect adjustment.
B1304202020-06-15. Service bulletin. ENGINE AND ENGINE COOLING. TANK VENTILATION AND MIXTURE CONTROL FAULTS STORED IN THE DME: The Engine Malfunction Warning is illuminated and one or more of the following faults are stored in the DME. All models: FC 191C02 - Fuel tank ventilation system 2nd discharge point: malfunction FC 195014 - Differential pressure sensor tank vent valve signal: fixed FC 118001 - Mixture control: mixture too lean FC 118401 - Mixture control: mixture too lean large deviation I01 only: FC 124103 - Mixture control: mixture too lean FC 124101 - Mixture control: Mixture lean large deviation CAUSE Internal mechanical defect in the tank ventilation valve. The defect can also result in a very loud clicking noise when the valve is cycling.
B8402142020-04-27. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY. CONNECTEDDRIVE/BMW ASSIST SYSTEM DIAGNOSIS INFORMATION: This Service Information Bulletin (Revision 7) replaces SI B84 02 14 dated May 2019. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information Bulletin: Is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. Will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
B6522142020-04-20. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). AUTOMATED ACTIVATION OF NAVIGATION SYSTEM DURING PDI/QC1: This Service Information Bulletin (Revision 2) replaces SI B65 22 14 dated October 2015. The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department! When the vehicle is connected to the diagnostic system ISTA to perform PDI/QC1 the step to activate the navigation system (part of Delete Transport Mode) will automatically request the INITIAL NAV enabling code (VIN-specific) without pre-ordering the enabling code. This enabling code will be automatically delivered through ISTA and it then activates the navigation system.
B6507202020-04-20. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT. VEHICLE SOUND GENERATOR IS DIFFERENT AND LOUDER AFTER PROGRAMMING: Vehicles sound is different and louder after programming to an Integration level (I-level) between I001-1911-500 and I001-19-11-556. Software in the Vehicle Sound Generator (VSG).
B6401202020-04-20. Service bulletin. ELECTRICAL SYSTEM; SERVICE BRAKES, HYDRAULIC; BACK OVER PREVENTION; FUEL SYSTEM, GASOLINE. AIR CONDITIONING DOES NOT COOL: The air conditioning no longer cools the vehicle. A vehicle test reveals one or both of the following faults stored in the IHX_I1 Control Module: 801295 - Heat Pump pressure-temperature sensor 2 after air condition compressor: pressure short to ground / open circuit 80112A - Heat Pump pressure-temperature sensor 2 after air condition compressor: temperature - short to ground A short circuit at the temperature sensor due to aluminum particles in the high-pressure line.
B6109202020-04-20. Service bulletin. ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC); ELECTRICAL SYSTEM; STEERING; SUSPENSION. CHECK CONTROL MESSAGES FOR BRAKE SUSPENSION AND AIR BAG SYSTEM MALFUNCTION: Multiple check control messages (CCM) can display for brake suspension and air bag system malfunction. The customer may also complain about any of the following: Engine can no longer be switched off Drive position (D) cannot be engaged on the gear selector switch (GWS) Reduction of steering assist After an engine emergency shut-off (either a prolonged long press; or 3 consecutive short presses of the Start/Stop button) and the vehicle going to sleep (identifiable by the lighting of the "Start/Stop button") everything resumes normal functionality and the CCM messages no longer appear.
B6105202020-04-20. Service bulletin. ENGINE. CCM DISPLAYED "INCREASED BATTERY DRAIN" CAUSED BY CONTROLLER: This Service Information Bulletin (Revision 1) replaces SI B61 05 20 dated February 2020. Electrostatic discharge at standstill / start engine. Energy management" The results of the Energy Diagnosis test plan identifies the Controller as the root cause of the CCM. The Controller delays the vehicle going to sleep by up to 6 minutes. In some cases this will cause the CCM 415 to be displayed when starting the vehicle. Replacing the Controller in this case will not correct this situation.
B5130162020-04-20. Service bulletin. AIR BAGS; PARKING BRAKE. TAILGATE UNINTENTIONALLY OPENS: This Service Information Bulletin (Revision 4) replaces SI B51 30 16 dated March 2018. Trunk/tailgate may open when vehicle is locked Trunk/tailgate may open while the vehicle is in motion usually after stopping such as a traffic light etc. Vehicle key trunk/tailgate button may be accidentally pressed thus opening the tailgate.
B3405172020-04-20. Service bulletin. BACK OVER PREVENTION; SERVICE BRAKES, HYDRAULIC; WHEELS; POWER TRAIN. TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: This Service Information Bulletin (Revision 3) replaces SI B34 05 17 dated September 2017. Ticking noise coming from front wheel while cornering without brakes applied noticeable at low speeds. The vehicle must be moving. See attached video V34 01 20 Note: For a similar noise heard when parking with the brakes applied refer to SIB 31 01 12. Microscopic movement of the contact interface between the inner brake disc and the wheel bearing flange on vehicles equipped with lightweight brake discs.
B3211192020-04-20. Service bulletin. FUEL SYSTEM, DIESEL:STORAGE:TANK ASSEMBLY; POWER TRAIN; AIR BAGS; STEERING. SPORADIC REDUCTION OF STEERING ASSISTANCE: This Service Information Bulletin (Revision 1) replaces SI B32 11 19 dated October 2019. The driver notices a reduction of steering assistance sporadically while in certain driving situations. Steering control is never lost when the reduction of assistance occurs. The fault may self-correct for no obvious reason or be eliminated with a terminal change/key cycle. There is no Check Control (CC) message when the issue occurs. Unfavorable software in the Electric Power Steering (EPS).
B7202202020-03-16. Service bulletin. SEAT BELTS. SAFETY BELT WARNING GONG SOUNDS AFTER UNBUCKLING WHILE VEHICLE IS STATIONARY. After a vehicle has been programmed to an I-level greater than 19-11-5xx and lower than I-level 20-03-530; the safety belt (aka seat belt) acoustic warning sounds when in Park (engine running) and the safety belt is unbuckled. The chime/gong lasts for up to 1 minute 40 seconds. The customer only expects the acoustic warning when the vehicle is moving and the safety belt is not buckled. The acoustic warning can occur when the seat is occupied and the safety belt buckle is opened on the driver's or passenger's side. Software in the ACSM4 Control Unit.
B6105202020-03-16. Service bulletin. ELECTRICAL SYSTEM. CCM DISPLAYED "INCREASED BATTERY DRAIN" CAUSED BY CONTROLLER. A yellow CCM (Check Control Message) ID 415 is displayed- "Increased battery drain! // Battery. Electrostatic discharge at standstill / start engine. Energy management" The results of the Energy Diagnosis test plan identifies the Controller as the root cause of the CCM. The Controller delays the vehicle going to sleep by up to 6 minutes. In some cases this will cause the CCM 415 to be displayed when starting the vehicle. Replacing the Controller in this case will not correct this situation.
B3202142020-02-18. Service bulletin. ELECTRICAL SYSTEM; STEERING. Power-assisted Steering Intermittently Not Available at Engine Start-up: This Service Information Bulletin (Revision 1) replaces SI B32 02 14 dated November 2016. The power-assisted steering is unavailable at start up/drive readiness. No communication with the Electric Power Steering (EPS). Possible fault codes: Fault code Text D356A5 message fault (display of the check control driving dynamics 02 D: Disp_CC_DRDY_02) Timeout D359BF message fault (actual steering torque of the driver actuator ID: AVL_STMOM_DV_ACT) Timeout D356B6 message fault (display of the check control driving dynamics 02 ID: DISP_CC_DRDY_02) - Alive 480AB8 internal status management of the complete monitoring range CDA451 FlexRay message (actual steering torque of the driver actuator 49.0.2): missing CDA452 FlexRay message (actual force of the rack 49.0.2): missing D35B26 message fault (actual position of the EPS ID: AVL_PO_EPS) - Timeout D355C4 message fault (status of the electrical steering front axle ID: ST_EST) - Timeout 48083B Peripheral/functional error on the engine control unit interface Actual steering angle of the front axle; signal temporarily invalid D35COC message fault (actual force of the rack ID: AVL_FORC_GRD) - Timeout. Electric Power Steering (EPS).
B6108152020-01-21. Service bulletin. ELECTRICAL SYSTEM. High-Voltage Charging Cable Lock Malfunction: One of the following situations can occur: The vehicle cannot be charged via the high-voltage charging procedure. The indicator light on the charging socket lights up white and does not change colors. The high-voltage charging cable cannot be unlocked and disconnected.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.