WenmarOpen by Wenmar Pro

Service bulletins for the 2014 BMW i3

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

313 on file from NHTSA, as of 2026-10-19.

By type

By component

Bulletins, newest first
B6510152018-11-05. Service bulletin. EQUIPMENT; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). NAV Road Map Installation Using USB Stick. INFORMATION The Navigation road map can be installed onto the head unit in the vehicle using a USB stick connected to the USB connector in the center console in the vehicle. ? 32GB USB stick is necessary ? Desired NAV road map version can be retrieved from the HDD-Update console PROCEDURE 1. Copy the desired NAV road map from the HDD-Update console onto a 32GB USB stick. Refer to Attachment. 3. When prompted, enter the 20-digit enabling code. 4. Start the NAV road map installation and follow the on-screen instructions. WARRANTY INFORMATION Not applicable. ATTACHMENTS View PDF attachment B651015_Attachment.
B6135142018-11-05. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:SOFTWARE. "Displayed Range Is Lower After Programming. After the vehicle is programmed with ISTA/P 3.53.3 (i-level I001-14-07-503), the displayed vehicle range in the instrument cluster is lower than prior to the software update. The actual range that the vehicle is capable of achieving on a full charge has not changed. The difference between the displayed range and actual range is always conservative, yet this difference varies based on driving profile. When driving primarily at highway speeds, the difference between displayed and actual range is within a few percent of each other. When driving primarily with a low speed/city profile, the gap may widen to as much as 20% or more. Software improvements have been made to the range algorithm to improve its accuracy in all driving scenarios. These updates are available with ISTA/P 3.55.0 (I-level I001-15-03-501). In addition, the following enhancements are integrated into this new I-level: ? The state of charge (SOC) percentage is visible in the upper left corner of the Kombi. It has been added to the board computer display in order for the customer to better manage the vehicle range. ? On vehicles from 3/2015 production, hospitality charging (charger sharing) has been added. This feature will automatically unlock the charge port when the vehicle is fully charged and still plugged in. This feature is not backwards-compatible to vehicles produced prior to 3/2015. ? REx only - if the SOC reaches 2.0% with the REx running, the message ""Low Battery. Power Reduction Possible."" will appear in the Kombi. In addition to the range display, the customer may notice that the vehicle's range has decreased as outside temperatures have gotten colder. This is most noticeable in extreme cold climates, and when preconditioning is not used. This situation does not indicate a problem and is independent of the range display algorithm. CAUSE The algorithm that determines the displayed range, was changed with the 14-07-503 software level. The r
B6118152018-11-05. Service bulletin. ELECTRICAL SYSTEM. Charging is not Possible, or is Reduced. ? Charging is no longer possible, or is only possible with restricted charging power, or: ? When charging the vehicle, the indicator light around the charging socket lights up red and the external circuit breaker (inside the A/C charger or A/C power supply) activates. CAUSE Hardware fault in the Electric Motor Electronics (EME), or the Convenience Charging Electronics (KLE).
B5116152018-11-05. Service bulletin. EQUIPMENT:OTHER:LABELS. "Affected vehicles in dealer inventory must not be retailed or delivered until the label is removed. Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a ""Vehicle Comment"" in the DCS Warranty Vehicle Inquiry or ISPA Light. Remove the engine oil label (located in the front or rear of the hood)."
B1232142018-11-05. Service bulletin. ENGINE. "Service Engine Soon (MIL) Lamp Illuminated with No Relevant Faults. INFORMATION If an i3 or i8 is brought in for service with a Service Engine Soon (MIL) lamp illuminated, or with a customer concern that the MIL is intermittently illuminated, troubleshoot with ISTA/D. During diagnosis, refer to the functional description (FUB), Troubleshooting Malfunction Indicator Lamp I01. This document explains the rationale behind what triggers an MIL on an electrified vehicle, as well as some diagnostic hints. If these diagnostics do not lead to a root cause and a solution, continue with the following: ? Do not clear faults with ISTA/D. ? Use the recommended ACTRON OBD scan tool to read out any code (P or U code) that is present. The ACTRON scan tool was sent to BMW centers via the automatic tool shipment program. For more information on this tool, refer to SI B04 18 15. ? Record any and all P/U codes. ? Look up the relevant code[s] in the attached document, SAE_P-Code_List.pdf. This list provides the description for BMW specific P/U codes. ? Match the P/U code[s] to the fault codes stored in the vehicle. Typically the P/U code description is very close to the fault code title. - NOTE: Even though multiple OBD-relevant fault codes may be stored in the vehicle, the P/U code displayed is what triggered the MIL. Therefore, continue diagnostics for the fault code associated with the P/U code displayed. ? If no P/U codes are displayed and ISTA/D diagnostics are inconclusive, submit a TC PuMA case entitled Check Engine Light - No Relevant Faults to either ""BMW i3 Powertrain Components"" or ""i8 Powertrain Components"" for further assistance. -The P code and diagnosis summary should be included in the case."
B6509152018-11-05. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EQUIPMENT:ELECTRICAL; EQUIPMENT. HU-H: Headunit Resets Intermittently or Permanently. The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H
B6304152018-11-05. Service bulletin. EXTERIOR LIGHTING:TAIL LIGHTS. "Traces of Condensation Appear in Rear Tailgate Lights After removing the rear circuit board, dry out the lens area with an adjustable temperature heat gun. It is important that the temperature not be higher than 140 F, to avoid damage to the lens and LED. . INFORMATION Covered under the terms of the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks. Defect Code:63 21 15 48 00Rear light, rear lid leaking Or: If you are using a Main labor code for another repair, use the Plus code labor operation 63 21 800 instead. Work time labor operation code 63 99 000 is not considered a Main labor operation. Also, since the ""work time"" FRU allowance to be claimed is specified, a separate punch time is not required. Other Repairs If the leak checking results in other eligible and covered work, claim this work with the applicable defect code and/or labor operations listed in KSD2. Overlapping Labor - Associated and/or Other Repairs If invoicing KSD2 flat rate labor operation codes for the additional repair work results in overlapping labor being claim, invoice work time labor operation 00 50 000 for the additional time (FRU) minus the overlap instead. On the repair order and in the claim comment section, please identify the labor operations labor operation code 00 50 000 replaces and itemize claimed FRU amount. Work time labor operation code 00 50 000 is not considered a Main labor operation. Associated Repairs: When work time labor operation 00 50 000 is used as an extension of the repair outlined in this bulletin, a separate defect code and punch time(s) are not required. Other Repairs: When work time labor operation 00 50 000 is used for work that will be claimed under different defect codes, separate punch time(s) are required."
B6135142018-11-05. Service bulletin. ELECTRICAL SYSTEM. "Displayed Range Is Lower After Programming. After the vehicle is programmed with ISTA/P 3.53.3 (i-level I001-14-07-503), the displayed vehicle range in the instrument cluster is lower than prior to the software update. The actual range that the vehicle is capable of achieving on a full charge has not changed. The difference between the displayed range and actual range is always conservative, yet this difference varies based on driving profile. When driving primarily at highway speeds, the difference between displayed and actual range is within a few percent of each other. When driving primarily with a low speed/city profile, the gap may widen to as much as 20% or more. Software improvements have been made to the range algorithm to improve its accuracy in all driving scenarios. These updates are available with ISTA/P 3.55.0 (I-level I001-15-03-501). In addition, the following enhancements are integrated into this new I-level: ? The state of charge (SOC) percentage is visible in the upper left corner of the Kombi. It has been added to the board computer display in order for the customer to better manage the vehicle range. ? On vehicles from 3/2015 production, hospitality charging (charger sharing) has been added. This feature will automatically unlock the charge port when the vehicle is fully charged and still plugged in. This feature is not backwards-compatible to vehicles produced prior to 3/2015. ? REx only - if the SOC reaches 2.0% with the REx running, the message ""Low Battery. Power Reduction Possible."" will appear in the Kombi. In addition to the range display, the customer may notice that the vehicle's range has decreased as outside temperatures have gotten colder. This is most noticeable in extreme cold climates, and when preconditioning is not used. This situation does not indicate a problem and is independent of the range display algorithm. CAUSE The algorithm that determines the displayed range, was changed with the 14-07-503 software level. The r
B6108152018-11-05. Service bulletin. ELECTRICAL SYSTEM. "High-Voltage Charging Cable Lock Malfunction. One of the following situations can occur: ? The vehicle cannot be charged via the high-voltage charging procedure. The indicator light on the charging socket lights up white and does not change colors. ? The high-voltage charging cable cannot be unlocked and disconnected. One of the following faults codes is also stored in the Charging Interface Module (LIM): 805532 ""High-voltage charging socket: Lock on the charging plug, status implausible"" 805503 ""High-voltage charging socket: Charging plug lock, line disconnection"" CAUSE ? The emergency-operation tensioning strap is jammed. ? The actuator drive for the charging socket is not working."
B6107152018-11-05. Service bulletin. ELECTRICAL SYSTEM. "Charging Stops when Using ""Occasional Use"" Cable. When charging the vehicle with the Occasional Use Cable (OUC), and the charge rate set to ""Min"" in the CID, charging may switch off during the charge cycle. In rare cases, the vehicle may not start the charging cycle at all. The following fault is stored in the Electric Machine Electronics (EME): 0x222843 - charging management: Charging target not reachable (power of charger too low) Updated software is available to prevent this situation from recurring. CAUSE The EME software had a minimum charging power threshold of 600W. On the ""Min"" charge setting in the CID, the target charging current is 6 amps. Therefore, if the available voltage at the wall socket dips below 100 volts at any time, charging will be switched off."
B5112152018-11-05. Service bulletin. STRUCTURE; EQUIPMENT. Front Door Trim Panel Loose. The door trim panel is loose or has a visible gap in the area near the B-pillar. The yellow door trim panel securing clips are not robust.
B3602152018-11-05. Service bulletin. TIRES:VALVE; WHEELS. Valve Stem Replacement with Wheel Electronics. INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] Page 1 of 3 Page 1 of 1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 Page 1 of 3 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015
B1220152018-11-05. Service bulletin. ENGINE; ELECTRICAL SYSTEM. "Service Engine Soon (MIL): RDME FC 120006. The Service Engine Soon light (MIL) is intermittently illuminated in the instrument cluster, and fault code 120006 ""Information engine switch-off time: too long compared to cooling of engine coolant"" is stored in the RDME. CAUSE Software error, faulty component, or cooling issue"
6138142018-11-05. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. ?SI B61 38 14 February 2015 General Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B61 38 14 dated January 2015. designates changes to this revision SUBJECT Drivetrain Malfunction (CCM 794) with Isolation Faults. The Drivetrain Malfunction check control message (CCM 794) is displayed, either while driving or when starting up. The following faults are stored in the vehicle: EME: 22280F and/or 222814 SME: 21F0E3 and/or 21F0E4 When the CCM is present, there are no apparent drivability concerns. After allowing the vehicle to rest and then restart, the CCM typically does not reappear. CAUSE The cause of an isolation fault is generally a resistance between HV+ or HV- and the shield/chassis ground, which is below a predetermined threshold. The following procedure addresses these faults when caused by a defect in the cable between the HV battery and the EME, as well as when excess moisture is present inside the REx eMachine. This moisture condenses and triggers the above-mentioned faults after a long REx runtime followed by rapid cooling.
6102152018-11-05. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. "MCheck Control Message ""Battery Discharge"" Displays Intermittently. The customer states that a ""Battery Discharge"" check control message is displayed intermittently when the vehicle is started. The following fault code is also stored: DME ""213901 - Power management: Reduction or switch-off of individual electrical consumers"" DME/IBS software error."
2201152018-11-05. Service bulletin. ENGINE AND ENGINE COOLING; STRUCTURE. SUBJECT Left Side Engine Mount Broken. The left side motor mount or motor mount support has failed. As a result, the electric drivetrain moves excessively in the chassis. A banging noise can be heard from the rear of the vehicle during load reversals. In addition, the vehicle may experience a Drivetrain Malfunction CCM or other electrical drivetrain failures. NOTE: If this failure is present, the vehicle should not be driven, as additional consequential damage could result. CAUSE The motor mount or motor mount support is damaged due to excessive shock to the driveline, such as a sudden loss of traction or underbody impact, during acceleration.
B8406162018-11-05. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT:ELECTRICAL. BMW ONLINE NON-FUNCTIONAL: CHECK ICC-ID IN ACCOUNT. BMW Online/BMW ConnectedDrive not functional. Vehicle and service cockpit have different ICC-ID's.
B8405162018-11-05. Service bulletin. EQUIPMENT:ELECTRICAL; EQUIPMENT ADAPTIVE/MOBILITY. BMW ONLINE NON-FUNCTIONAL: CHECK ICC-ID IN ACCOUNT. The ConnectedDrive Services are non-functional after a hardware exchange of the telematics control unit. This is not indicated by CC-message. ConnectedDrive Services not synchronized by Telematics Control Unit.
B6618162018-11-05. Service bulletin. ELECTRICAL SYSTEM. INFORMATION ON THE OPERATION OF THE SMART OPENER. INFORMATION ON THE OPERATION OF THE SMART OPENER MODEL F07 (5 Series Gran Turismo) F10 (5 Series) F12 (6 Series Convertible) F13 (6 Series Coupe) F15 (X5) F16 (X6) F22 (2 Series Coupe) F23 ( 2 Series Convertible) F25 (X3) F26 (X4) F30 (3 Series Sedan) F31 (3 Series Wagon) F32 (4 Series Coupe) F33 (4 Series Convertible) F34 (3 Series Gran Turismo) F36 (4 Series Gran Coupe) F48 (X1) F80 (M3 Sedan) F82 (M4 Coupe) F83 (M4 Convertible) F85 (X5 M) F86 (X6 M) G12 (7 Series) I01 (i3 Series) Vehicles with option code SA-0322 (Comfort Access) without M-Sport trim INFORMATION The smart opener (Contactless tailgate) operates as described below: Ignition key must be within 3 feet behind the vehicle, clear from any interference like a smartphone The customer must be at least an arms-length behind the vehicle Kick your foot forwards & backwards under the vehicle in one quick movement The taillights flash confirming that the trunk will open The trunk then successfully opens For more information an instructional video can be viewed which demonstrates the operation. Thanks to BMW of Tenafly for providing the video. tinyurl.com/Autotrunk1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016 Page 2 of 2 WARRANTY INFORMATION Not applicable. [ Copyright (c)2016 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016
B6413162018-11-05. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. "A/C FAILURE: FC 801252 ELECTRIC A/C COMPRESSOR: INTERNAL FAULT DETECTED. Air conditioning (A/C) failure with IHKA fault code ""801252 - Electric A/C compressor: Internal fault detected"". IHKA software fault in the versions detailed in the following table: ModelISTA/P versionIntegration levelF153.57.3F025-15-11-505F303.57.2F020-15-11-504I01, I123.57.0I001-15-11-501"
B5130162018-11-05. Service bulletin. STRUCTURE:BODY:TAILGATE; STRUCTURE:BODY:TRUNK LID. TAILGATE UNINTENTIONALLY OPENS. Trunk/tailgate may open when vehicle is locked. Trunk/tailgate may open while the vehicle is in motion. Usually after stopping, such as a traffic light etc. Vehicle key trunk/tailgate button may accidentally be pressed, thus opening the tailgate.
B5116152018-11-05. Service bulletin. EQUIPMENT:OTHER:LABELS; ENGINE. "Delivery Stop: Remove Engine Oil Label. Affected vehicles in dealer inventory must not be retailed or delivered until the label is removed. Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a ""Vehicle Comment"" in the DCS Warranty Vehicle Inquiry or ISPA Light. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/248...9/3/2016 Page 2 of 2"
B3203152018-11-05. Service bulletin. STEERING. NOISES WHEN TURNING THE STEERING WHEEL This Service Information bulletin supersedes SI 32 03 15 dated January 2016.. There are squeaking or groaning noises from the steering spindle when the steering wheel is turned. The steering spindle sleeve's plastic bearing is insufficiently lubricated or not lubricated at all.
B6527162018-11-05. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. SOFTWARE CHANGES AFTER PROGRAMMING WITH ISTA/P V3.59.2. INFORMATION Aftersales customer service representatives need to be aware of the following changes that occur to features and functions of the i01 (i3) after reprogramming and encoding by ISTA/P 3.59.2 to integration level 16-07-503. An additional option, in the detail view of the Points of Interest (POI), to display valid charging stations for charging a BMW i vehicle. This list is automatically compiled through BMW i drivers successfully charging their vehicle. This list may now be filtered to include only the 20 charging locations with the most charging outlets in the area. Without the filter, the system will still display up to 5000 charging stations in a 300km (186 m) radius. Vehicles with 5AR Traffic Jam Assistant or 5AT Driving Assistant Plus produced before 07/2014 - Traffic Jam Assistant is now operational up to 60km/h (37 mph). Its operation was previously only available up to 40 km/h (25 mph). The range display has been optimized when the navigation system is activated. Previously, when the navigation system was activated, the range would be reduced because of a difference in the algorithms used by the navigation system and the instrument cluster for range calculation. They have been optimized and the effect on the range display has been minimized. [ Copyright (c)2016 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/37...12/6/2016
B6518162018-11-05. Service bulletin. EQUIPMENT; AIR BAGS. AIRBAG WARNING LAMP ILLUMINATED This Service Information bulletin Replaces SI B65 18 16 dated July 2016.. The airbag warning lamp in the instrument cluster lights up while the vehicle is in motion. The airbag control unit (ACSM4) contains the following fault(s): 930904 - Drivers airbag interval stage 1, resistance too high 93090A - Drivers airbag interval stage 2, resistance too high Tension caused by harness cable tie on short jumper harness located between steering column slip ring and driver's airbag creates excess resistance.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.