WenmarOpen by Wenmar Pro

Service bulletins for the 2014 BMW ActiveHybrid 3

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

443 on file from NHTSA, as of 2026-10-19.

By type

By component

By topic

Bulletins, newest first
6308142018-11-13. Service bulletin. EXTERIOR LIGHTING:HEADLIGHTS. Active Headlight Control Malfunction in Both Headlights. AHL (Active Headlight Control) malfunctions on both sides. Both lights aim either up or down while driving. CAUSE Broken mounting bolt holding on the rear height sensor bracket
3301142018-11-13. Service bulletin. POWER TRAIN. "?SI B33 01 14 March 2014 Rear AxleTechnical Service. This Service Information bulletin supersedes SI B33 01 14 dated February 2014. PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. designates changes to this revision SUBJECT Delivery Stop/Service Action: Check Rear Axle Differential. 1 A Delivery Stop has been issued on certain 2014 model year F15 and F3x vehicles produced from July 2013 to January 2014 because the final drive differential gears may not have been properly hardened. Vehicles held at the ports of entry are being inspected and/or repaired prior to center delivery. During this inspection and analysis of data, BMW of North America has documented a failure rate of less than one in two hundred. The affected vehicles are listed in the attachment to this bulletin; they are also identified with a ""Vehicle Comment"" in the DCSnet Warranty Vehicle Inquiry or ISPA as follows: ??Defect Code 0033840100, Delivery Stop: Rear Axle Differential; see SI B 33 01 14 The initial limited available stock of parts is reserved for vehicles that have already been sold and are in customers' hands (see Situation 2). Affected vehicles in center inventory must not be retailed or delivered until the rear differential has been replaced. 2 Certain 2014 model year F15 and F3x vehicles produced from July 2013 to January 2014 may have final drive differential gears that have not been properly hardened. These vehicles have already been sold and delivered to customers."
B6519152018-11-13. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EQUIPMENT. XM Satellite Radio Reception. INFORMATION Currently Satellite Radio is provided by SiriusXM for BMW customers. SiriusXM is the only company currently broadcasting Satellite Radio in North America. Satellite radio is broadcast from two different sets of Satellites using different earth orbits. XM uses geosynchronous (GEO) satellites located roughly above the equator. This means that the satellite signal to some parts of the United States can come in at an angle as low as 32 degrees to the horizon. This is different than Sirius Satellites in a Highly Elliptical Orbit (HEO) which currently come in to the vehicle at a higher angle to the horizon. As of April 2016 Sirius equipped head units will move to the XM Satellites constellation and will show the same location based cutouts. SiriusXM is currently updating the repeater network to cover areas of low reception, but the general disadvantage of geostationary satellites can't be compensated completely. Buildings, hills, trees, highway sound blocking walls or any other obstacles might block the satellite signal coming from the south at a 32 degree elevation angle and might cause audio cut outs in absence of terrestrial repeaters. Reception quality decreases the further north you travel, as the angle of the incoming signal gets flatter. Adverse weather conditions will affect reception. Sirius XM will increase the amount of Sirius and XM repeaters gradually to improve situation in metropolitan areas. When investigating Satellite Radio cutouts or a temporary loss of reception: Please compare to a similarly equipped vehicle. Do not compare an XM equipped vehicle to a Sirius equipped vehicle. Replace no parts Customers should direct all reception complaints to one of the following: BMW Customer Relations department at either 1-800-831-1117 or customerrelations@bmwusa.com BMW Genius Hotline 1-844-443-6487 or to the dealers onsite BMW Genius Customers must provide the exact location (street address or Latitude/Longitude), weathe
B6212152018-11-13. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Instrument Cluster Outside Temperature Display Implausible. INFORMATION This service information bulletin provides technical, diagnostic and/or repair-related information. Eligible and Covered Work/Repairs To submit a claim for the repair of a verified defect in materials or workmanship, please following the established and applicable warranty policy and procedures together with the using corresponding defect code and labor operations provided in the KSD2.
B6211152018-11-13. Service bulletin. ELECTRICAL SYSTEM. Head-Up Display (HUD) Rattling Noises During Image Adjustment or While Driving. When operating the Head-Up Display (HUD) adjustment a noise can be heard from inside the dashboard behind the Instrument Cluster. While driving over rough roads something can be heard rattling inside the HUD. Internal HUD failure.
B6123152018-11-13. Service bulletin. VISIBILITY:WINDSHIELD WIPER/WASHER. "The Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full. INFORMATION The use of a ""non-approved"" washer fluid can cause the low fluid warning light to come on even when the reservoir is full. An analysis of parts returned to warranty has shown the sensor is operating correctly. Do not replace the reservoir with integrated sensor for these situations. We recommend using ""BMW Group approved"" washer fluid when servicing the vehicle or performing repairs on the windshield washer system. Refer to ISTA document ""FB-GZ-B17A-F20 Washer fluid level sensor"" for information on how this capacitive sensor operates. If the correct washer fluid is being used, diagnose the system using normal troubleshooting with ISTA. A fault code may be stored if an electrical fault occurs in the circuit. PARTS INFORMATION Part NumberDescriptionQuantity83 19 2 406 220BMW WWS Cold Weather Concentrate 35% 55 GalAs needed83 19 2 361 205BMW Windshield Washer Concentrate 1 GalAs neededNote: As applicable, do not exceed your state's maximum for the allowable amount/percentage of ""Washer Concentrate"" that can be used when mixing the windshield washer fluid solution. WARRANTY INFORMATION The issue described in this bulletin is not a vehicle-related defect in materials or workmanship. If a vehicle repair is required as a result of this issue, it is are not claimable under a BMW limited warranty."
B3408142018-11-13. Service bulletin. SERVICE BRAKES, HYDRAULIC. ?SI B34 08 14 Brakes December 2015 Technical Service This Service Information bulletin supersedes SI 34 08 14 dated July 2015. designates changes to this revision SUBJECT Ticking Noise from Front Axle When Cornering. The customer may complain of a ticking noise from the front axle when cornering, maneuvering, parking or pulling away from a parking space. The noise can be heard as a light metallic ticking from the front outer cornering wheel. Movement between the brake disc and wheel bearing hub.
B1233142018-11-13. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING. Fault Code 1D2008 Stored in DME. The Service Engine Soon light is on. Fault Code 1D2008: Map thermostat: jammed open is stored in the DME. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up, the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat.
B1126152018-11-13. Service bulletin. POWER TRAIN; ENGINE. Delivery Stop: B58 Engine - Check Crankshaft Bearing Shells.A Delivery Stop has been issued on F30 and F32 certain vehicles produced from July 2015 (start of production) to December 2, 2015. These vehicles may have upper guide bearing shells that may exhibit wear at low mileage. There are 45 vehicles affected by this stop. For your convenience, attached you will find the list of affected VINs. This bulletin will be updated with repair instructions and warranty information when it becomes available. Affected vehicles can be identified with a ?Vehicle Comment? in DCS Warranty Vehicle Inquiry or ISPA Light with a specific description.
B6509152018-11-13. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL. HU-H: Headunit Resets Intermittently or Permanently. The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H
B6406132018-11-13. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING; EQUIPMENT:APPLIANCE:AIR CONDITIONER. A/C Cooling: Intermittent Reduction of Air Flow. Customer may complain of reduced air flow when the air conditioning system is operated for an extended time, usually longer than 30 minutes. INFORMATION Possibility of reproducing this situation is improved by the following conditions ? High outside ambient temperature ? High humidity Note: It is very difficult to duplicate this issue. The fault may be reproduced under the following conditions: ? Air-conditioning system switched on ? Driving Experience switch NOT set to Eco Pro ? Slower fan speeds ? Temperature setting below 68°F (20°C) ? Trip duration at least 30 minutes ? Outside temperature above 68°F (20°C) NOTE: After parking the vehicle or switching off the air-conditioning system for at least 20 minutes, the symptom disappears (ice melts off evaporator and puddles under the car from the A/C drains.). Evaporator starts to freeze up due to the position of the evaporator temperature sensor.
B6517152018-11-13. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL; EQUIPMENT. "Active Sound Design ASD inoperative after programming. After programming with ISTA/P V3.56.1 Active Sound Design (ASD) no longer provides simulated engine sounds A fault is stored in the ASD module. Fault Code 8053A5 ""ASD; invalid coding data for equalizing"" Invalid ASD coding data"
B3601152018-11-13. Service bulletin. TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS. Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
B3302152018-11-13. Service bulletin. POWER TRAIN:AXLE ASSEMBLY. "Grinding or cracking noise when putting vehicle in gear/ ""Drive Disturbed"" displayed. A metallic grinding or cracking noise is heard from the rear of the vehicle when selecting Drive or Reverse. There may also be a Check Control message ""Drive Disturbed"" displayed. CAUSE The inner and/or outer universal joint on the right and/or left rear output shaft has failed."
B1607152018-11-13. Service bulletin. FUEL SYSTEM, GASOLINE; FUEL SYSTEM, DIESEL:STORAGE:TANK ASSEMBLY. Fuel Tank Non-Return Valve Faults with SES Light. Check Engine Light is illuminated and the following faults are stored in the DME: 0x191A94 - Fuel tank non-return valve: clamped shut 0x191A93 - Fuel tank non-return valve: clamped open CAUSE Software and hardware errors
B1114152018-11-13. Service bulletin. ENGINE AND ENGINE COOLING. The plastic oil filter housing may fail and lead to an internal and/or external engine oil or coolant leak.
B6126142018-11-13. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:HORN. "Horn(s) Fail to Work. While trying to activate the horn, one or both horns fail to work. One or more of the following fault codes can be stored in the FEM: ? ""8044A3 - Wiring, horn short circuit to earth"" ? ""8044A4 - Wiring, horn short circuit to positive"" ? ""8044A5 - Wiring, horn relay is defective or short circuit to positive"" Water has entered the horn and caused it to fail internally (shorted out)."
B3601152018-11-13. Service bulletin. TIRES; WHEELS. Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
B2402152018-11-13. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. 8HP: Transmission Fluid Loss from Cooler Lines Connections. There is a transmission fluid leak in the area around the oil cooler lines (on the transmission side). CAUSE Damaged o-rings due to unfavorable cooling line connection tolerances
1215132018-11-13. Service bulletin. ENGINE. ?N20 and N26 Engine: Various VANOS System Faults Stored in DME. The Service Engine Soon lamp and Engine Malfunction warning are illuminated, and the vehicle has reduced power output. This situation can occur as a customer complaint, or after performing repairs to the engine valve train assembly. One or more of the following faults is stored in the DME. F10, F25, F30, F31 and F34: 131401 VANOS, exhaust, starting from cold: Non-adjustable 131501 VANOS, intake, starting from cold: Non-adjustable 131808 VANOS, exhaust, starting from cold: Position not reached 131908 VANOS, intake, starting from cold: Position not reached 130104 VANOS, intake, control fault, camshaft jammed 130304 VANOS, exhaust, control fault, camshaft jammed 130308 VANOS, exhaust, control fault, position not reached 130108 VANOS, intake, control fault, position not reached E84 and E89: 2D54 VANOS, exhaust, starting from cold: Non-adjustable 2D55 VANOS, intake, starting from cold: Non-adjustable 2D56 VANOS, exhaust, starting from cold: Position not reached 2D57 VANOS, intake, starting from cold: Position not reached 2D60 VANOS, exhaust, control fault, camshaft jammed 2D5A VANOS, intake, control fault, camshaft jammed 2D5B VANOS, intake, control fault, position not reached 2D61 VANOS, exhaust, control fault, position not reached If one of the applicable faults listed above is not stored in the DME fault memory then continue troubleshooting with the applicable test plan for the fault(s) stored. CAUSE This is due to a diagnostic programming error in the DME.
B8405142018-11-13. Service bulletin. EQUIPMENT. One or both of the situations listed below may be encountered: ? Android device connection stability (dropped calls) ? Third-Party App Metadata: The album art and song title do not update when streaming audio from Pandora or Spotify, etc. New KISU (Customer Initiated Software Update) software is available on the TIS website. This software improves the Bluetooth functionality in our vehicles, and it helps to keep us up-to-date with technology innovation.
B6602152018-11-13. Service bulletin. VEHICLE SPEED CONTROL:CRUISE CONTROL. "Remote Control Not Detected and/or Engine Will Not Start. One or more of the following situations can occur: 1. The remote control is not detected and the check control message (CCM) ""No remote control. Unable to start"" or ""Hold the remote control on the steering column"" is displayed. ? Fault code ""D90D1E - LIN bus error FBD receiver 1"" is stored. 2. The engine does not start with the CCM with ""Battery in the key is dead."" However, it must work when used with the second key. ? Fault Code ""9308B0 - ID transmitter: Battery undervoltage"" is stored. 3. The remote control is not detected and the CCM ""Central locking does not open,"" and/or ""Engine fails to start"" is displayed. An outside influence is causing interference with the remote control or the battery in the remote control key is defective."
B6303152018-11-13. Service bulletin. EXTERIOR LIGHTING:HEADLIGHTS. "Halogen Headlight Side Bulbs Fail. The check control message (CCM) ""Parking lamp malfunction: Consult service center"" is displayed when the vehicle is started. Defective side light bulb on one or both sides"
B6104152018-11-13. Service bulletin. VISIBILITY:REAR WINDOW WIPER/WASHER; ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:HORN. Horn Blows when Unlocking Vehicle. The customer states that the vehicle horn sounds briefly when unlocking the vehicle or opening the door. In some cases, the washers spray briefly on the windshield. Front Electronics Module (FEM) software error
B5103152018-11-13. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT. "Front Floor Mats Do Not Stay in Place. The Velcro patch attached to the bottom of the floor mat peels off. Poor adhesion of the Velcro patch Thank you for all the PuMA ""Info Only"" cases. From these cases, it has been determined that the Velcro peeling fault occurs on mats produced prior to May 2014. We no longer need ""Info Only"" cases from this time period."

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.