WenmarOpen by Wenmar Pro

Service bulletins for the 2003 BMW 760Li

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

21 on file from NHTSA, as of 2026-10-19.

By type

By component

Bulletins, newest first
B5108192024-02-01. Service bulletin. VISIBILITY:POWER WINDOW DEVICES AND CONTROLS; ELECTRICAL SYSTEM. The basic conditions for initializing the power windows are not met.
B1606232024-01-03. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING. Engine will crank but not start. There is no communication with the integrated fuel module (TFE) whendiagnosing with ISTA. The following two fault codes will be stored in the DME: 032B43 - Low fuel pressure system, electric fuel pump: pressure value too low CDA594 - Message (- 0x33E) missing, receiver DME, transmitter TFE
B6534232023-12-06. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Customers may state that the alarm system (DWA) is not active after locking their unoccupied vehicle. Depending on the vehicle’s equipment and settings, no acoustic or optical confirmation (folding the mirrors/blinking confirmation) is noticeable. Additionally, the red anti-theft alarm LED in the interior mirror does not briefly flash every 2 seconds, indicating the alarm is armed.
SIB0105222022-08-22. Service bulletin. ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC); SUSPENSION. Component-Specific Limited Warranty Extension For the eligible vehicles, BMW of North America, LLC (BMW NA) is extending the limited warranty for the vehicle's front and rear air suspension strut assemblies (item # 1 Front and # 2 Rear, shown) to: 8 years/80,000 miles, as determined by the vehicle's original in-service date. Other air suspension system-related components/issues are excluded from this coverage. This component-specific limited warranty extension applies to defects in materials or workmanship. This coverage is subject to the same vehicle eligibility requirements, limitations, and exclusions that apply to the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks.
6302102018-12-17. Service bulletin. EXTERIOR LIGHTING:TURN SIGNAL. Check Control Message Displayed; Turn Signals Flash Fast.
B0703142018-12-10. Service bulletin. ENGINE; STEERING; ELECTRICAL SYSTEM; EQUIPMENT. This Service Information bulletin supersedes SI B07 03 14 dated October 2015. Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
6113052018-12-03. Service bulletin. ELECTRICAL SYSTEM. "Discharged Battery: Energy Diagnosis Must Be Performed. The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle ""discharged battery"" complaints. A discharged battery can have various causes, most of which do not concern the battery itself. A failed battery is often the symptom and not the cause. A fully serviceable battery fails when an electrical component causes the battery to discharge; the battery becomes internally damaged and must be replaced. For more information, refer to www.batteryuniversity.com/parttwo-42B.htm For this reason, replacing the battery is not usually a permanent repair. The cause of the discharged battery must be analyzed in order to guarantee a proper repair. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion with all results taken into to consideration. The procedure as outlined below contains information that will guide the technician into properly repairing the vehicle and getting paid for a warranty claim. CAUSE Refer to the ""Procedure"" section of this Service Information for details."
0703142018-11-26. Service bulletin. EQUIPMENT. Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
6103142018-11-13. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; ELECTRICAL SYSTEM. Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting
6103142018-11-13. Service bulletin. ELECTRICAL SYSTEM. Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shut
6304142018-11-13. Service bulletin. EXTERIOR LIGHTING. Delay in Automatic Driving Light Switching On/Off. When driving out of a tunnel or exiting underground parking, the automatic driving light remains switched on for two minutes, even in daylight. The automatic driving light switching on/off can be shorter or longer when it starts to get dark. CAUSE The software for the switch-on threshold is lowered to protect the xenon light source.
B0703142018-11-13. Service bulletin. EQUIPMENT. This Service Information bulletin supersedes SI B07 03 14 dated May 2015. designates changes to this revision SUBJECT Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
1208152018-11-13. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE. "SUBJECT N62TU: ISTA Service Function for DME ""RAM Backup"". The ISTA Service Function test plan should be performed to clear stored values in the DME RAM memory after repairs are completed, in the following situations: z VANOS or engine-related repairs if any of the following faults cannot be cleared: 2A90 - Exhaust camshaft, tooth offset to crankshaft 2A91 - Exhaust camshaft 2, tooth offset to crankshaft 2A8A - Inlet VANOS, adaptation stop 2A8B - Inlet VANOS, adaptation stop 2 2A8C - Exhaust VANOS, adaptation stop 2A8D - Exhaust VANOS, adaptation stop 2 2A8E - Inlet camshaft, tooth offset to crankshaft 2A8F - Inlet camshaft 2, tooth offset to crankshaft z The engine oil level display continues to show as overfilled even after being corrected. This is also described in SI B12 05 07."
B0703142018-11-05. Service bulletin. ELECTRICAL SYSTEM. Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
0703142018-11-05. Service bulletin. ELECTRICAL SYSTEM. This Service Information bulletin supersedes SI B07 03 14 dated February 2015. designates changes to this revision SUBJECT Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
B0703142018-11-05. Service bulletin. ELECTRICAL SYSTEM. Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits This Service Information bulletin supersedes SI B07 03 14 dated October 2015.. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
B6507092018-10-09. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). NAVIGATION SYSTEM: REPORTING MISSING OR INCORRECT ROAD MAP DATA: The route guidance is inaccurate and therefore irritating to the customer; or it is not possible to locate certain addresses, for instance:
B6507092018-08-06. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). NAVIGATION SYSTEM: REPORTING MISSING OR INCORRECT ROAD MAP DATA: The route guidance is inaccurate and therefore irritating to the customer; or it is not possible to locate certain addresses, for instance:
SIB-63-02-012011-04-28. Service bulletin. EXTERIOR LIGHTING. BMW: PROCEDURE FOR DETERMINING AND REPLACING INCANDESCENT AND HALOGEN LIGHT BULBS UNDER WARRANTY. *RM
SIB-32-04-072011-04-26. Service bulletin. STEERING:ELECTRIC POWER ASSIST SYSTEM; STEERING:HYDRAULIC POWER ASSIST SYSTEM. BMW: A NEW TECHNICAL PROCESS HAS BEEN CREATED FOR BMW TO IDENTIFY CAUSES OF STEERING COMPLAINTS WITH A WIDE RANGE OF MODELS. *RM
SIB-16-02-092010-07-14. Service bulletin. FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP. BMW VEHICLES: FUEL LEVEL SENSOR REPAIRS. WHERE IT IS NECESSARY TO REPLACE THE RIGHT OR THE LEFT SIDE FUEL LEVEL SENSOR DUE TO A FAILURE, THE ENTIRE PUMP AND HOUSING OR DELIVERY UNIT (SUCTION JET ASSEMBLY) DO NOT NEED TO BE REPLACED AS WELL. IN SOME CASES, EPC DOES NOT SHOW THAT THE REPAIR KIT IS AVAILABLE SEPARATELY IN THE ILLUSTRATION, BUT IT IS AVAILABLE IN THE PARTS DESCRIPTION. ALL MODELS. NO MODEL YEARS LISTED. *PE

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.