WenmarOpen by Wenmar Pro

Service bulletins for the 2016 BMW 528i

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

208 on file from NHTSA, as of 2026-10-19.

By type

By component

Bulletins, newest first
1204152018-11-13. Service bulletin. ELECTRICAL SYSTEM; ENGINE. SUBJECT DME Internal and Valvetronic Faults Set at Cold Ambient Temperatures. The Service Engine Soon light (MIL) can be illuminated with the erroneous internal and Valvetronic faults stored in the DME. The MIL will only come on if the fault has been detected on two (or more) consecutive drive cycles. The following fault codes may be stored in the DME: E Seriesz 36AE - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 2DE2 - Valvetronic, actuation, voltage phase: Line disconnection z 2DE3 - Valvetronic, actuation, volt phase: Line disconnection z 2DE4 - Valvetronic, actuation, volt phase: Line disconnection F Seriesz 1F0905 - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 135B10 - Valvetronic, actuation, voltage phase: Line disconnection z 135B11 - Valvetronic, actuation, volt phase: Line disconnection z 135B12 - Valvetronic, actuation, volt phase: Line disconnection Engine performance and driving characteristics are not affected. DME software diagnostic sensitivity.
1201152018-11-13. Service bulletin. POWER TRAIN. SUBJECT N20 and N26 Differential Pressure Sensor Fault 195002 Stored in DME. The Service Engine Soon (MIL) light is on with the following differential pressure sensor fault stored: z 195002 - Differential pressure sensor, tank vent valve, electrical: Short circuit to ground During engine operation, vibration and movement of the sensor can damage the pin contacts of the harness connector, or cause a break in the wiring.
B3304162018-11-13. Service bulletin. SERVICE BRAKES. Delivery Stop: Replace Rear Differential.
B1209162018-11-13. Service bulletin. ENGINE AND ENGINE COOLING. N20 - The Service Engine Soon Light is On with DME Fault 118602 Stored. The Service Engine Soon light is on (MIL) with only the following oxygen sensor fault stored. 118602 - Oxygen sensor before catalytic converter, fine mixture control: exhaust gas after catalytic converter too lean CAUSE An actual engine related problem and/or DME software diagnostic.
B1111152018-11-13. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM. Service Action: Replace the Thermostat. The Service Engine Soon light is on with corresponding fault codes in the DME for the engine thermostat.
B3404142018-11-05. Service bulletin. SERVICE BRAKES, HYDRAULIC; SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC. Diagnosis of Compound Brake System Complaints in M Vehicles This Service Information bulletin supersedes SI 34 04 14 dated December 2014. Designates changes to the bulletin. INFORMATION 1.Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form. These surface hairline cracks are usually spread over the entire brake disc friction area, and have no negative influence on the durability or braking performance. The rotors should not be replaced only for their appearance reasons.When performing routine service on the brake system (pad replacement due to wear), the brake discs should be replaced if surface cracks are found to be greater than 13 mm, or if the brake disc thickness is below the minimum thickness. Always replace brake discs in pairs (per axle). Install new brake pads when replacing discs. By doing this, the service life of the friction pad surface is increased, and an even material loss is ensured. 2. Vibrations and/or steering wheel torsional vibrations during braking are caused by applying the brakes on discs with minimal to heavy corrosion. These vibrations are most noticeable when braking from high speeds with cold brake components (less than 212 degrees F), and will diminish with normal everyday operation. Parts replacement is not required. 3.After high brake loads, running noises can be heard when applying the brakes, and may also be heard to a limited extent after the brakes are released. (See the note in the Owner's Manual). These noises are reduced during normal everyday operation, due to further erosion of the brake pad friction lining. Visible surface cracks or craterlike recesses on the brake pad surface are caused by a minor difference in the material of the pad lining, which will decrease with further operation and should not be replaced due to their appearance.
B2704152018-11-05. Service bulletin. POWER TRAIN:DRIVELINE; WHEELS. Shudder from the Driveline on Vehicles with xDrive. There is a shudder or vibration from the driveline when taking off from a stop, or when accelerating at highway speeds. CAUSE Possible multiple root causes related to the engine, wheels & tires, suspension components or internal wear on the clutch plates of the xDrive transfer case.
B1116152018-11-05. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. ?N20 and N26 engine: Smoke from Exhaust when Starting a Cold Engine. When starting a cold engine, blue smoke can be seen emitting from the exhaust tailpipe for approximately 10-20 seconds. No turbo charger boost faults are stored and no drivability issues can be detected. Engine oil leakage into the induction system and/or the turbo charger assembly.
B6510152018-11-05. Service bulletin. EQUIPMENT; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). NAV Road Map Installation Using USB Stick. INFORMATION The Navigation road map can be installed onto the head unit in the vehicle using a USB stick connected to the USB connector in the center console in the vehicle. ? 32GB USB stick is necessary ? Desired NAV road map version can be retrieved from the HDD-Update console PROCEDURE 1. Copy the desired NAV road map from the HDD-Update console onto a 32GB USB stick. Refer to Attachment. 3. When prompted, enter the 20-digit enabling code. 4. Start the NAV road map installation and follow the on-screen instructions. WARRANTY INFORMATION Not applicable. ATTACHMENTS View PDF attachment B651015_Attachment.
B5116152018-11-05. Service bulletin. EQUIPMENT:OTHER:LABELS. "Affected vehicles in dealer inventory must not be retailed or delivered until the label is removed. Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a ""Vehicle Comment"" in the DCS Warranty Vehicle Inquiry or ISPA Light. Remove the engine oil label (located in the front or rear of the hood)."
B3301152018-11-05. Service bulletin. STRUCTURE; POWER TRAIN. Cracking in Rear Differential Mount Bushing. During inspection, the rear differential mount in the rear axle support shows signs of cracking.
B1302152018-11-05. Service bulletin. FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP. "?SI B13 02 15July 2015 Fuel SystemsTechnical Service This Service Information bulletin supersedes SI B13 02 15 dated May 2015. designates changes to this revision SUBJECT Service Action: N63 Replace High-Pressure Fuel Pumps. The high-pressure pump may fail, resulting in an engine malfunction warning and reduced engine output. This Service Action involves F01, F02, F04, F07, F10, F12, F13, E70, E71, and E72 vehicles with the N63 engine produced from January 1, 2011 to December 1, 2011. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. CAUSE The high-pressure pump quantity control valve may fail."
B1221142018-11-05. Service bulletin. FUEL SYSTEM, OTHER:STORAGE:FUEL GAUGE SYSTEM; ELECTRICAL SYSTEM:SOFTWARE; FUEL SYSTEM, GASOLINE. Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
B6509152018-11-05. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EQUIPMENT:ELECTRICAL; EQUIPMENT. HU-H: Headunit Resets Intermittently or Permanently. The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H
B6103142018-11-05. Service bulletin. ELECTRICAL SYSTEM. Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can occur. The check control message (ID 229) is caused by a heavily discharged battery. ? The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). ? In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. ? Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. ? The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting down certain electrical consumers.
B3602152018-11-05. Service bulletin. TIRES:VALVE; WHEELS. Valve Stem Replacement with Wheel Electronics. INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] Page 1 of 3 Page 1 of 1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 Page 1 of 3 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015
B1302152018-11-05. Service bulletin. FUEL SYSTEM, GASOLINE. Service Action: N63 Replace High-Pressure Fuel Pumps. The high-pressure pump may fail, resulting in an engine malfunction warning and reduced engine output.
B1221142018-11-05. Service bulletin. ELECTRICAL SYSTEM. ?SI B12 21 14May 2015 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 21 14 dated April 2015. designates changes to this revision SUBJECT Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
B1108152018-11-05. Service bulletin. ENGINE. N63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. ? B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs ? B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints ? B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity ? B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. ? Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine ? Excessive engine oil consumption ? Spark plugs fouled with engine oil
6504142018-11-05. Service bulletin. AIR BAGS. "Airbag Warning Light: ACSM FC 930A60 or 930A1C Seat Occupancy Detection. According to the customer, the airbag warning light was on, but it may not be on when the vehicle arrives in the workshop. 1. ACSM fault code ""930A60 - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. Or 2. ACSM fault code ""930A1C - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. CAUSE The front passenger seat occupancy mat consists of a seat occupancy mat with a capacitive sensor system. This means a front passenger is detected by measuring the resistance of the human body. The fault is set when moisture is detected on the mat itself."
6103142018-11-05. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored. When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE ? The check control message (ID 229) is caused by a heavily discharged battery. ? The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). ? In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. ? Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. ? The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting down certain electrical consumers.
3409142018-11-05. Service bulletin. WHEELS. SUBJECT Wheel Speed Sensor Faults Cannot Be Cleared. The Dynamic Stability Control (DSC) warning light comes on while driving. The following DSC fault codes for the wheel speed sensors are stored: ? 480712 and/or ? 480715 and/or ? 480718 and/or ? 48071B They cannot be cleared, even though the wheel speed sensors work correctly and no problem can be found with the wiring harness. Due to high outside temperatures and extremely low atmospheric humidity, an electrostatic discharge (ESD) can occur in the wheel well area. This can transfer to the wheel speed sensor, causing irreparable damage to the DSC control unit.
1221142018-11-05. Service bulletin. ENGINE; ELECTRICAL SYSTEM. SI B12 21 14February 2015 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 21 14 dated December 2014. designates changes to this revision SUBJECT Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: z FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
1123142018-11-05. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE; EQUIPMENT. SI B11 23 14February 2015 EngineTechnical Service This Service Information bulletin supersedes SI 11 23 14 dated January 2015. PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. designates changes to this revision SUBJECT Service Action: Replace the Thermostat (F10). The Service Engine Soon light is on with corresponding fault codes in the DME for the engine thermostat. CAUSE Moisture and corrosion could develop on the electrical contacts for the heater circuit in the thermostat.
B8406162018-11-05. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT:ELECTRICAL. BMW ONLINE NON-FUNCTIONAL: CHECK ICC-ID IN ACCOUNT. BMW Online/BMW ConnectedDrive not functional. Vehicle and service cockpit have different ICC-ID's.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.