WenmarOpen by Wenmar Pro

Service bulletins for the 2014 BMW 435i

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

391 on file from NHTSA, as of 2026-10-19.

By type

By component

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
B1116152018-12-10. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER; ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER. February 2016 Engine Technical Service This Service Information Bulletin supersedes SI B11 16 15 dated September 2015 SUBJECT N20 and N26 engine: Smoke from Exhaust when Starting a Cold Engine. When starting a cold engine, blue smoke can be seen emitting from the exhaust tailpipe for approximately 10-20 seconds. No turbo charger boost faults are stored and no drivability issues can be detected. CAUSE When the vehicle is parked overnight the engine oil pressure will equalize and may leak past the turbo charger exhaust side turbine seal.
B1110152018-12-10. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE; EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY. ?Service Action: Replace the Thermostat. Please perform the procedure outlined in this Service Information on all affected vehicles before customer delivery. In the event the customer has already taken delivery of the vehicle, please perform the procedure the next time the vehicle is in the shop. This Service Information bulletin supersedes SI B11 10 15 dated January 2016.
B1110152018-12-10. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. The Service Engine Soon light is on with corresponding fault codes in the DME for the engine thermostat.
6406132018-12-03. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; ENGINE AND ENGINE COOLING. A/C Cooling: Intermittent Reduction of Air Flow. The customer may complain of reduced air flow when the air conditioning system is operated for an extended time, usually longer than one hour. The complaint can vary due to one or more of the following variables: * High outside ambient temperature * Too much humidity * A/C temperature and fan settings set too low for too long Note: It is very difficult to duplicate this issue due the required outdoor weather conditions and length of driving time needed. CAUSE Evaporator starts to freeze up due to the position of the evaporator temperature sensor
1701142018-11-26. Service bulletin. ENGINE AND ENGINE COOLING. Low Coolant Level with No Sign of External Leaks. The Low Coolant Warning light is on and there are no signs of a visual leak. Pressure testing the cooling system may or may not show an internal leak (loss of pressure). There may also be a complaint of transmission fluid leaking from the vent on top of the transmission; poor shift quality; or a shuddering from the transmission. There is an internal failure of the automatic transmission oil cooler, allowing coolant to mix with transmission fluid. Possible faulty coolers were built between 6/6/2013 and 8/4/2013.
1305142018-11-26. Service bulletin. ENGINE. . INFORMATION To properly diagnose the customer's complaint, the applicable test plan for the misfire faults stored in the DME must be performed to avoid repeat repairs. If a misfire fault is not stored in the DME memory and an engine related drivability complaint is received, follow the path below to manually start the misfire test plan (AT1214_TVD4_MISFIRE_20): 1. Perform a vehicle test. 2. Select "Function Structure." 3. Select "01 Engine." 4. Select "Engine electronics MEVD." 5. Select "Misfire detection." 6. Follow the steps in the test plan and select "Basic check (start)" first. Do not select "Additional check" at this time. 7. If the result of the "Basic check" indentifies a fuel system component failure, replace the identified component. If the result of the "Basic check" test plan was inconclusive, go to step 7. After the component replacement, perform the "Basic check" portion of the test plan again to verify if the diagnosis was correct and the vehicle condition has been rectified.
1229142018-11-26. Service bulletin. ENGINE AND ENGINE COOLING. Reduced Engine Performance. When driving with high outside ambient temperatures, repeated stop and go, or high-load operation over longer distances, the engine performance can be reduced. The air-conditioning system blower output may also be reduced, and in some circumstances, the compressor is switched off. One or both of the following faults are stored in the DME: 1A2108: Electric fan, self-diagnosis, interval stage 1: Minor fan fault 241400: Electric fan, diagnosis feedback 1: Fan slightly stiff The Service Engine Soon lamp (MIL) would not be illuminated in these situations. 1. A DME software error in the control of the 600W electric fan over-boost or high speed function 2. The electric cooling fan design was not robust enough for continuous over-boost or high-speed operation.
1701142018-11-13. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN. Low Coolant Level with No Sign of External Leaks. The Low Coolant Warning light is on and there are no signs of a visual leak. Pressure testing the cooling system may or may not show an internal leak (loss of pressure). There may also be a complaint of transmission fluid leaking from the vent on top of the transmission; poor shift quality; or a shuddering from the transmission. There is an internal failure of the automatic transmission oil cooler, allowing coolant to mix with transmission fluid. Possible faulty coolers were built between 6/6/2013 and 8/4/2013.
1233142018-11-13. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. Fault Code 1D2008 Stored in DME. The Service Engine Soon light is on. Fault Code 1D2008: Map thermostat: jammed open is stored in the DME. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up, the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat.
0104142018-11-13. Service bulletin. ENGINE AND ENGINE COOLING. External Engine Oil Leaks and Repairs. During the vehicle's operational life, normal engine oil seepage or sweating, in addition to accumulated road dust, dirt and grime in the engine compartment can cause the appearance of a more severe oil leak. This is further exaggerated by residual oil that remains on the engine assembly after maintenance services are performed, e.g., oil filter changes, "engine oil top-offs," etc. If this visual appearance of accumulated oil on the engine assembly as an "active leak" is misinterpreted, unnecessary gasket repairs/replacements will result. Specifically, our analysis of the claim-related data for vehicles equipped with the engines noted in this bulletin is showing an above-average number of engine gasket repair/replacement claim submissions. The purpose of this bulletin is to provide your workshop with information and a procedure that will help in identifying engine oils leaks that do and do not require a repair.
6407132018-11-13. Service bulletin. VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:FAN/MOTOR; ENGINE AND ENGINE COOLING. Service Action: Replace Blower Motor Regulator. The blower motor regulator has an internal fault; after starting the engine, there may be a delay of up to a minute before the blower motor comes on CAUSE Faulty blower motor regulator (output stage)
1225132018-11-13. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING. Reduced Engine and Air-Conditioning Performance. When driving with high outside ambient temperatures, repeated stop and go, or high load operation over longer distances, the engine performance can be reduced. The air-conditioning system blower output may also be reduced, and in some circumstances the compressor is switched off. There could be any of the following faults stored depending on the conditions present at the time. DME * Fault 1A2108: Electric fan, self-diagnosis, interval stage 1: Minor fan fault EGS (also possibly set) * Fault 421722: DME/DDE interface: Forced upshift due to thermal engine protection request IHKA (possibly set without DME or EGS faults) * Fault 801224: Air conditioning compressor: Shut-down due to excess pressure in refrigerant circuit * Fault 801228: Blower output stage: Blower output reduction due to power management The Service Engine Soon lamp (MIL) would not be illuminated in these situations. 1. A DME software error in the control of the 850W electric fan over-boost or high speed function. 2. The electric cooling fan design was not robust enough for continuous over-boost or high speed operation.
6407132018-11-13. Service bulletin. ENGINE AND ENGINE COOLING; VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:FAN/MOTOR; VISIBILITY. Service Action: Replace Blower Motor Regulator. The blower motor regulator has an internal fault; after starting the engine, there may be a delay of up to a minute before the blower motor comes on CAUSE Faulty blower motor regulator (output stage)
6406132018-11-13. Service bulletin. ENGINE AND ENGINE COOLING; VISIBILITY. ?SI B64 06 13 January 2014 Body EquipmentTechnical Service This Service Information bulletin supersedes SI B64 06 13 dated November 2013. designates changes to this revision SUBJECT A/C Cooling: Intermittent Reduction of Air Flow. The customer may complain of reduced air flow when the air conditioning system is operated for an extended time, usually longer than one hour. The complaint can vary due to one or more of the following variables: * High outside ambient temperature * Too much humidity * A/C temperature and fan settings set too low for too long Note: It is very difficult to duplicate this issue due the required outdoor weather conditions and length of driving time needed. CAUSE Evaporator starts to freeze up due to the position of the evaporator temperature sensor
6406132018-11-13. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; ENGINE AND ENGINE COOLING. A/C Cooling: Intermittent Reduction of Air Flow. The customer may complain of reduced air flow when the air conditioning system is operated for an extended time, usually longer than one hour. The complaint can vary due to one or more of the following variables: * High outside ambient temperature * Too much humidity * A/C temperature and fan settings set too low for too long Note: It is very difficult to duplicate this issue due the required outdoor weather conditions and length of driving time needed. CAUSE Evaporator starts to freeze up due to the position of the evaporator temperature sensor
B1233142018-11-13. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING. Fault Code 1D2008 Stored in DME. The Service Engine Soon light is on. Fault Code 1D2008: Map thermostat: jammed open is stored in the DME. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up, the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat.
B1126152018-11-13. Service bulletin. POWER TRAIN; ENGINE. Delivery Stop: B58 Engine - Check Crankshaft Bearing Shells.A Delivery Stop has been issued on F30 and F32 certain vehicles produced from July 2015 (start of production) to December 2, 2015. These vehicles may have upper guide bearing shells that may exhibit wear at low mileage. There are 45 vehicles affected by this stop. For your convenience, attached you will find the list of affected VINs. This bulletin will be updated with repair instructions and warranty information when it becomes available. Affected vehicles can be identified with a ?Vehicle Comment? in DCS Warranty Vehicle Inquiry or ISPA Light with a specific description.
B6406132018-11-13. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING; EQUIPMENT:APPLIANCE:AIR CONDITIONER. A/C Cooling: Intermittent Reduction of Air Flow. Customer may complain of reduced air flow when the air conditioning system is operated for an extended time, usually longer than 30 minutes. INFORMATION Possibility of reproducing this situation is improved by the following conditions ? High outside ambient temperature ? High humidity Note: It is very difficult to duplicate this issue. The fault may be reproduced under the following conditions: ? Air-conditioning system switched on ? Driving Experience switch NOT set to Eco Pro ? Slower fan speeds ? Temperature setting below 68°F (20°C) ? Trip duration at least 30 minutes ? Outside temperature above 68°F (20°C) NOTE: After parking the vehicle or switching off the air-conditioning system for at least 20 minutes, the symptom disappears (ice melts off evaporator and puddles under the car from the A/C drains.). Evaporator starts to freeze up due to the position of the evaporator temperature sensor.
B1233142018-11-13. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING. Fault Code 1D2008 Stored in DME. The Service Engine Soon light is on. Fault Code 1D2008: Map thermostat: jammed open is stored in the DME. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up, the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat.
B1103152018-11-13. Service bulletin. ENGINE. N20 and N26 Engine: Oil Leaks from Cylinder Head Cover. There is an engine oil leakage under the vehicle, or the vehicle smells of engine oil. The cylinder head cover gasket is leaking engine oil due to loose retaining bolt(s).
1240142018-11-13. Service bulletin. ENGINE; ELECTRICAL SYSTEM. "SUBJECT N55 and NPOW: DME Fault 102001, Air Mass Too High, Sets in ECO PRO Mode. The Service Engine Soon light (MIL) comes on while driving at moderate to highway speeds in ECO PRO with the ""Coasting"" feature selection active. z Fault 102001: Air mass, plausibility: Air mass too high is stored in the DME BMW Power Kit DME software"
1239142018-11-13. Service bulletin. ENGINE. SUBJECT N55: Engine Briefly Shudders or Runs Erratically After Cold Start. Under certain cold starting conditions, the engine may shudder or run a bit erratically for the first few moments when starting off. This can be felt at an engine speed of approximately 1,500 rpm. No relevant faults are stored in the DME memory. DME software calibration
1238142018-11-13. Service bulletin. FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM; ENGINE. SUBJECT N20, N26, and N55 Engines with Injector Electrical Faults. Any of the following symptoms could occur simultaneously with injector electrical faults stored in the DME: z After the engine is turned off for a short time, it can no longer be started; however, the starter motor turns. z The engine starts but immediately cuts off. z The engine runs erratically or lacks power. z The Service Engine Soon light (MIL) may be on with several poetential faults stored. The DME has malfunctioned due to an internal fault.
1204152018-11-13. Service bulletin. ELECTRICAL SYSTEM; ENGINE. SUBJECT DME Internal and Valvetronic Faults Set at Cold Ambient Temperatures. The Service Engine Soon light (MIL) can be illuminated with the erroneous internal and Valvetronic faults stored in the DME. The MIL will only come on if the fault has been detected on two (or more) consecutive drive cycles. The following fault codes may be stored in the DME: E Seriesz 36AE - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 2DE2 - Valvetronic, actuation, voltage phase: Line disconnection z 2DE3 - Valvetronic, actuation, volt phase: Line disconnection z 2DE4 - Valvetronic, actuation, volt phase: Line disconnection F Seriesz 1F0905 - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 135B10 - Valvetronic, actuation, voltage phase: Line disconnection z 135B11 - Valvetronic, actuation, volt phase: Line disconnection z 135B12 - Valvetronic, actuation, volt phase: Line disconnection Engine performance and driving characteristics are not affected. DME software diagnostic sensitivity.
1102152018-11-13. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV). SUBJECT Deleting DME Adaptations After Crankshaft Sensor-related Repairs. The erroneous misfire faults are stored, and the Service Engine Soon light (MIL) illuminates The ISTA Service Function to delete the DME adaptations fails to clear the crankshaft incremental wheel adaptation, depending on the current DME software version. This adaptation must be cleared whenever the following repairs are made: 1. Replacement of the crankshaft position sensor 2. Replacement of the incremental sensor wheel on the crankshaft 3. Replacement of the crankshaft 4. Replacement of the crankcase (block) with pistons 5. Replacement of the engine assembly Due to slight tolerance differences with the new replacement hardware and the original learned crankshaft position, values could cause cylinder balance calculation errors by the DME. DME software (the incremental wheel adaptation cannot be cleared)

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.