WenmarOpen by Wenmar Pro

Service bulletins for the 2015 BMW 428i

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

418 on file from NHTSA, as of 2026-10-19.

By type

By component

Bulletins, newest first
B6520152018-11-13. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT:ELECTRICAL. Noise from speaker grills/ surrounds. There may be interference noises (rattles, squeaks, clicking) from the front or rear speaker grill/surrounds when the audio is on. CAUSE ? Contact between front door panel or speaker grill/surround with the speaker cone. ? Contact between the front door panel armrest support and trim for the folding compartment. ? Contact between the rear speaker grill/surround with the speaker cone.
B6509152018-11-13. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL. HU-H: Headunit Resets Intermittently or Permanently. The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H
B6406132018-11-13. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING; EQUIPMENT:APPLIANCE:AIR CONDITIONER. A/C Cooling: Intermittent Reduction of Air Flow. Customer may complain of reduced air flow when the air conditioning system is operated for an extended time, usually longer than 30 minutes. INFORMATION Possibility of reproducing this situation is improved by the following conditions ? High outside ambient temperature ? High humidity Note: It is very difficult to duplicate this issue. The fault may be reproduced under the following conditions: ? Air-conditioning system switched on ? Driving Experience switch NOT set to Eco Pro ? Slower fan speeds ? Temperature setting below 68°F (20°C) ? Trip duration at least 30 minutes ? Outside temperature above 68°F (20°C) NOTE: After parking the vehicle or switching off the air-conditioning system for at least 20 minutes, the symptom disappears (ice melts off evaporator and puddles under the car from the A/C drains.). Evaporator starts to freeze up due to the position of the evaporator temperature sensor.
B8404152018-11-13. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. "The illumination (back lighting) for the E-Call (Emergency/SOS call) button in the FZD (sunroof module) overhead console does not work. This picture shows the E-Call button illumination (back lighting) not working. Note: Pressing the E-Call button will start an SOS call, even though the back lighting is not working.This picture shows E-Call illumination (back lighting) working. AFFECTED VEHICLES This Service Action involves the F34 (3 Series Gran Turismo) and F36 (4 Series Gran Coupe) models, produced from 7/27/2015 to 7/30/2015. Please perform it the next time this vehicle comes to your workshop. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. Missing wiring harness for the illumination of the E-Call button."
B6606152018-11-13. Service bulletin. ELECTRICAL SYSTEM. Sporadic Check Control Messages of the Driver Assistance System. Sporadically, a CCM (Check Control Message) is displayed advising that the Camera-based Driver Assistant system has failed. This is due to the vehicle interior reaching very high temperatures. During this failure, all KAFAS (Camera-based driver assistance systems) system functionalities are inoperative. The affected functionalities are: Pedestrian Detection Front Collision Warning Lane Departure Warning Speed Limit Info (if equipped) The following fault code is stored in the KAFAS control unit: 0x800AC0 - Switching off due to excess temperature Note: The system is functional after the interior temperature has cooled down or by cycling the ignition off and on again. Incorrect calibration of the temperature sensor in the KAFAS camera.
B3601152018-11-13. Service bulletin. TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS. Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
B3302152018-11-13. Service bulletin. POWER TRAIN:AXLE ASSEMBLY. "Grinding or cracking noise when putting vehicle in gear/ ""Drive Disturbed"" displayed. A metallic grinding or cracking noise is heard from the rear of the vehicle when selecting Drive or Reverse. There may also be a Check Control message ""Drive Disturbed"" displayed. CAUSE The inner and/or outer universal joint on the right and/or left rear output shaft has failed."
B6126142018-11-13. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:HORN. "Horn(s) Fail to Work. While trying to activate the horn, one or both horns fail to work. One or more of the following fault codes can be stored in the FEM: ? ""8044A3 - Wiring, horn short circuit to earth"" ? ""8044A4 - Wiring, horn short circuit to positive"" ? ""8044A5 - Wiring, horn relay is defective or short circuit to positive"" Water has entered the horn and caused it to fail internally (shorted out)."
B3601152018-11-13. Service bulletin. TIRES; WHEELS. Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
B2402152018-11-13. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. 8HP: Transmission Fluid Loss from Cooler Lines Connections. There is a transmission fluid leak in the area around the oil cooler lines (on the transmission side). CAUSE Damaged o-rings due to unfavorable cooling line connection tolerances
B8405142018-11-13. Service bulletin. EQUIPMENT. One or both of the situations listed below may be encountered: ? Android device connection stability (dropped calls) ? Third-Party App Metadata: The album art and song title do not update when streaming audio from Pandora or Spotify, etc. New KISU (Customer Initiated Software Update) software is available on the TIS website. This software improves the Bluetooth functionality in our vehicles, and it helps to keep us up-to-date with technology innovation.
B6602152018-11-13. Service bulletin. VEHICLE SPEED CONTROL:CRUISE CONTROL. "Remote Control Not Detected and/or Engine Will Not Start. One or more of the following situations can occur: 1. The remote control is not detected and the check control message (CCM) ""No remote control. Unable to start"" or ""Hold the remote control on the steering column"" is displayed. ? Fault code ""D90D1E - LIN bus error FBD receiver 1"" is stored. 2. The engine does not start with the CCM with ""Battery in the key is dead."" However, it must work when used with the second key. ? Fault Code ""9308B0 - ID transmitter: Battery undervoltage"" is stored. 3. The remote control is not detected and the CCM ""Central locking does not open,"" and/or ""Engine fails to start"" is displayed. An outside influence is causing interference with the remote control or the battery in the remote control key is defective."
B6104152018-11-13. Service bulletin. VISIBILITY:REAR WINDOW WIPER/WASHER; ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:HORN. Horn Blows when Unlocking Vehicle. The customer states that the vehicle horn sounds briefly when unlocking the vehicle or opening the door. In some cases, the washers spray briefly on the windshield. Front Electronics Module (FEM) software error
B6103152018-11-13. Service bulletin. ELECTRICAL SYSTEM. General Electrical Systems Technical Service. Various Check Control Messages Caused by Shorted K-CAN. The customer states that one or more of the following CC messages are displayed: ? 627 - Steering behavior: Drive moderately ? 070 - Steering: Drive moderately ? 765 - Rear-end collision restricted ? 850 - Pedestrian warning restricted ? 236 - Driving stabilization: Drive moderately ? 299 - SOS call system failure ? 042 - Brake system: Drive moderately After performing a vehicle test, one or more of the following fault codes are stored: ? ACSM - C9549A Message faulty (seat memory), ACSM receiver, driver's seat module transmitter ? FEM - D91DE0 No message, receiver FEM, transmitter TMSL ? FEM - D91EE5 No message, receiver FEM, passenger seat module transmitter ? ACSM - C9540C Message missing, receiver ACSM, transmitter FEM ? TMSL - D95402 Message missing, receiver TMSL, transmitter FEM ? KOMBI - E11454 No message, receiver KOMBI, transmitter REM ? FEM - D91DE6 No message, receiver FEM, transmitter TMSL ? TMSR - D99401 Message missing, receiver TMSR, transmitter FEM ? TMSR - D99402 Message missing, receiver TMSR, transmitter FEM ? FEM - 8041BA AHL system faulty ? FEM - D916C3 No message, receiver FEM, transmitter TCB ? ZBE - E2D403 No message, receiver CON, transmitter FEM-ZGM ? TRSVC - CA9428 Message incorrect, receiver TRSVC, transmitter PDC-REM ? TMSL- D95401 Message missing, receiver TMSR, transmitter FEM ? HU-H - S0397 MOST configuration was not stored ? TCB - E1445F KCAN2 or KCAN4: Line fault/electrical fault ? FEM - 8041B6 LWR faulty ? REM - E58468 Body CAN2; communication fault ? TRSVC - CA9427 Message incorrect, receiver all around vision camera, transmitter PDC/REM ? FEM - D91CEC Message missing, receiver FEM, transmitter REM Shorted KCAN wiring under driver or passenger seat.
B5103152018-11-13. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT. "Front Floor Mats Do Not Stay in Place. The Velcro patch attached to the bottom of the floor mat peels off. Poor adhesion of the Velcro patch Thank you for all the PuMA ""Info Only"" cases. From these cases, it has been determined that the Velcro peeling fault occurs on mats produced prior to May 2014. We no longer need ""Info Only"" cases from this time period."
B5101152018-11-13. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT:ELECTRICAL; EQUIPMENT. Harman Kardon Surround Sound System Noise. The customer may complain of a groaning/grinding noise in the area of the rear speakers. Lack of clearance between the tweeter and the mounting contact and/or wires.
B1233142018-11-13. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING. Fault Code 1D2008 Stored in DME. The Service Engine Soon light is on. Fault Code 1D2008: Map thermostat: jammed open is stored in the DME. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up, the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat.
B1103152018-11-13. Service bulletin. ENGINE. N20 and N26 Engine: Oil Leaks from Cylinder Head Cover. There is an engine oil leakage under the vehicle, or the vehicle smells of engine oil. The cylinder head cover gasket is leaking engine oil due to loose retaining bolt(s).
8401152018-11-13. Service bulletin. EQUIPMENT:ELECTRICAL; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT. "MSUBJECT iPhone and iOS 8.x Information. INFORMATION With the release of iOS 8.0, please be aware of the important functional change noted below: Scenario: z The customer leaves the vehicle and turns the phone off. z He or she turns the phone back on. z The customer then enters the vehicle, but does not unlock the phone prior to turning the vehicle on. https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20701.1.M840115....3/2/2015 Page 2 of 2 Result: z The phone reconnects to the Bluetooth system (normal). z However, the contact list is not transferred (not normal). z The contact list in the iDrive will be empty. z The call list in the Kombi will display only phone numbers, but no names. z The hands-free system works for accepting calls and conversing on calls started on the phone. Solution: z Prior to the customer entering the vehicle, he or she must unlock the phone at least once (passkey). With the release of Apple's new iPhone 6, 6 Plus and iOS 8.x software, there have been many questions regarding the new phone and software. The information in the attachment to this Service Information will help answer these questions. A printed copy can be given to the customer if needed. The attachment provides information on the differences between the new iPhone 6, 6 Plus and the previous versions, along with Apple software improvements in the following areas: 1. Visual comparison 2. Connectivity 3. Functionality Refer to the PDF file in the ""Attachment"" section of this bulletin for complete details. Information on the iPhone 6 is also available via the following website: www.miniusa.com/bluetooth NOTE: This SI will be updated as new information is received. "
6524132018-11-13. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). This Service Information bulletin supersedes SI B65 24 13 dated January 2014. designates changes to this revision SUBJECT Headunit-High: INITIAL Enabling Code Is Not Accepted Via I-Drive. INFORMATION Do not replace parts and do not program the vehicle for this issue. First-time activation of the navigation system should always be performed during the Quality Certification 1 (QC1) Pre-Delivery Inspection (PDI), with the vehicle connected to the ISTA diagnosis system. Refer to SI B65 22 14. WARRANTY INFORMATION Not applicable since the first time activation of the navigation system is part of the QC1 process and cannot be claimed separately. [ Copyright (c)2015 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20588.1.B652413....3/2/2015
6513122018-11-13. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT. This Service Information bulletin supersedes SI B65 13 12 dated September 2012. designates changes to this revision SUBJECT Headunit High: Navigation System Road Map Usage. INFORMATION The Headunit High (HU-H), also called NBT, began replacing the Car Information Computer (CIC) on certain MY2013 vehicles with option 609. This change will affect the navigation system road map data support process and the warranty spare parts processes for the HU-H. For the US market, all vehicles will come pre-loaded from the factory with the latest navigation system road map database version that was available at the time of vehicle production. Therefore, there will be no physical copy of the navigation system road map data media DVD set or USB stick placed in these vehicles at the Vehicle Distribution Center (VDC). NOTE: Additionally, all replacement HU-H parts come with a pre-loaded version of the current available navigation system road map database installed. A set of DVD copies of the navigation system road map database, HU-H NAVI Road Map North America NEXT, is shipped to all BMW centers through the automatic tool shipment program with each release of a navigation system road map database. IMPORTANT: Additional copies or earlier NAV road map database versions cannot be ordered individually! Therefore, please take special care to archive the HU-H NAV road map DVD sets! The NAV road map data on the DVD set can also be installed into the Network Attached Storage (NAS). From there it then can be installed onto the HU-H in the vehicle, using the Integrated Service Technical Application for Programming (ISTA/P). For installation of the navigation system road map data media DVD set onto the Network Attached Storage (NAS), please contact your ISPI NEXT Administrator. In addition to this procedure, it is also possible to download the NAV road map data on the DVD set directly to the hard disc drive (HDD) integrated in the HU-H by inserting the DVDs one by one into the HU-H internal DVD
6302152018-11-13. Service bulletin. EXTERIOR LIGHTING:BRAKE LIGHTS; PARKING BRAKE:INDICATOR LIGHT. "SUBJECT Check Control Message: Parking Light Failed. z A CCM (Check Control Message) displays ""Parking Light failed."" z All lights are functioning correctly. Software error in the TMS (Driver Module for Headlight)"
6134142018-11-13. Service bulletin. SEATS. "?This Service Information bulletin supersedes SI B61 34 14 dated December 2014. PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. designates changes to this revision SUBJECT Service Action: Replace Neck Warmer Control Unit. The control unit for the front seat neck warmers may not be coded correctly. This causes the neck warmer to malfunction. Incorrect coding of the neck warmer control unit AFFECTED VEHICLES This Service Action involves F33 and F83 vehicles produced to November 2014. First check if a Service Action label with a code number 724 is already attached to the B-pillar. If a code number 724 has been punched out, the Campaign has already been performed and no further action is necessary. Vehicles which require this Service Action will show it as ""Open"" when the VIN is checked in the ""Service Menu"" of DCSnet (Dealer Communication System) or when the key is read in the Key Reader."
3408142018-11-13. Service bulletin. WHEELS; SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC. "SUBJECT Ticking Noise from Front Axle When Cornering. Covered under the terms of the BMW New Vehicle/SAV Limited Warranty. Defect Code:34 11 00 57 00Labor Operation:Labor Allowance:Description:34 11 220Refer to KSDRemoving and installing both front brake discsAnd:34 99 0002 FRUWork time for sanding hub surface of brake discs and cleaning wheel hub surfacesLabor operation code 34 11 220 is a Main labor operation. If you are using a Main labor code for another repair, use the Plus code labor operation 34 11 609 instead. With the front brake calipers removed, use 34 11 612, or with the front brake pads removed, use 34 11 613. Refer to KSD2 for the corresponding flat rate unit (FRU) allowance. Enter the Chassis Number, which consists of the last 7 digits of the Vehicle Identification Number (VIN). Click on the ""Search"" button, and then enter the applicable flat rate labor operation in the FR code field. Even though work time labor operation code 34 99 000 ends in ""000"", it is not considered a Main labor operation. Also, since the ""work time"" FRU allowance to be claimed is specified, a separate punch time is not required."
1240142018-11-13. Service bulletin. ENGINE; ELECTRICAL SYSTEM. "SUBJECT N55 and NPOW: DME Fault 102001, Air Mass Too High, Sets in ECO PRO Mode. The Service Engine Soon light (MIL) comes on while driving at moderate to highway speeds in ECO PRO with the ""Coasting"" feature selection active. z Fault 102001: Air mass, plausibility: Air mass too high is stored in the DME BMW Power Kit DME software"

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.