WenmarOpen by Wenmar Pro

Service bulletins for the 2015 BMW 328d

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

442 on file from NHTSA, as of 2026-10-19.

By type

By component

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
1114142018-11-26. Service bulletin. ENGINE. Engine Damage Due to Debris in Oil Passages. After performing extensive engine repairs (e.g., cylinder head removal), the engine begins to knock and may lose power. Debris has entered the engine oiling passages during cleaning of the engine block and cylinder head mating surfaces during engine repair.
7102142018-11-13. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL; EQUIPMENT:OTHER:LABELS. Service Action: Replace Emission Label. Certain 2015 model year vehicles with N47T and N57T diesel engines were produced with an "emissions" label which contains incorrect information pertaining to the 2015 model year. Affected vehicles in dealer inventory must not be retailed or delivered until this issue is corrected. Vehicles at VDCs will be repaired prior to dealer delivery.
6206132018-11-13. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ENGINE. Condition Based Service Due Date Is Reset to 01/2000. The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster.
1301142018-11-13. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL; FUEL SYSTEM, DIESEL. "N47T and N57T Diesels with SCR Efficiency Faults Stored. A. The Service Engine Soon lamp is on (MIL) with either or both of the following SCR efficiency faults stored in the DDE: * 26F500 - SCR system, efficiency: Efficiency too low * 26F600 - SCR system, efficiency: Efficiency too low B. In addition, a Check Control message of ""Incorrect diesel exhaust fluid"" may be displayed with ""no start scenario countdown"" active. This would cause any of the following additional faults to be stored, depending on the SCR system status at the time. * 2CE400 - SCR system: System error and poor urea/water mixture quality detected * 26FD00 - Reducing agent metering, long-term adaptation: Adaptation value too high * 29FB00 - SCR system, warning and deactivation scenario: Warning level 1 * 29FC00 - SCR system, warning and deactivation scenario: Warning level 2 CAUSE Unfavorable DDE software"
1616142018-11-13. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Service Engine Soon Light (MIL) is On with SCR Fault 805220 Stored. The Service Engine Soon light is on with the following fault stored in the Selective Catalyst Reduction module (SCR). z 805220 - Delivery module, system pressure, pressure build-up is too low. This fault is very likely to be stored at temperatures below 32°F / 0°C if the vehicle is programmed using ISTA/P 3.54.1 or 3.54.2. Unfavorable SCR software
1233142018-11-13. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. Fault Code 1D2008 Stored in DME. The Service Engine Soon light is on. Fault Code 1D2008: Map thermostat: jammed open is stored in the DME. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up, the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat.
1801142018-11-13. Service bulletin. ENGINE AND ENGINE COOLING. Exhaust Leak on Diesel Particulate Filters. An exhaust leak develops on the Diesel Particulate Filter (DPF) around the area of the flexible coupling. Age or wear on the flexible coupling
1302142018-11-13. Service bulletin. ENGINE AND ENGINE COOLING. N47T: Diesel Particulate Sensor Faults Stored in DDE. The Service Engine Soon lamp (MIL) is on with any of the following diesel particulate sensor faults stored: * 2BB700 - Particulate sensor, plausibility: Sensor protective pipe plugged * 2BB600 - Particulate sensor, diagnosis response: Measuring electrode, bypass detection * 2BB300 - Particulate sensor, diagnosis response: Measuring electrode, self-diagnosis * 2BA100 - Particulate sensor, diagnosis response: Temperature measurement, electrical fault These stored faults would not cause a problem with engine performance. Unfavorable DDE software
1301142018-11-13. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL. SUBJECT N47T and N57T Diesels with SCR Efficiency Faults Stored. A. The Service Engine Soon lamp is on (MIL) with either or both of the following SCR efficiency faults stored in the DDE: * 26F500 - SCR system, efficiency: Efficiency too low * 26F600 - SCR system, efficiency: Efficiency too low B. In addition, a Check Control message of "Incorrect diesel exhaust fluid" may be displayed with "no start scenario countdown" active. This would cause any of the following additional faults to be stored, depending on the SCR system status at the time. * 2CE400 - SCR system: System error and poor urea/water mixture quality detected * 26FD00 - Reducing agent metering, long-term adaptation: Adaptation value too high * 29FB00 - SCR system, warning and deactivation scenario: Warning level 1 * 29FC00 - SCR system, warning and deactivation scenario: Warning level 2 CAUSE Unfavorable DDE software.
1303142018-11-13. Service bulletin. ELECTRICAL SYSTEM; ENGINE. Service Engine Soon Lamp (MIL) On with NOx Sensor Faults Stored. The Service Engine Soon lamp (MIL) is on with either of the following nitrogen oxide (NOx) sensor faults stored: * 2B6200 - NOx sensor before DeNOx catalytic converter, plausibility: Sensor self-diagnosis of sensitivity * 2B6300 - NOx sensor After DeNOx catalytic converter, plausibility: Sensor self-diagnosis of sensitivity These stored faults would not cause a problem with engine performance. This NOx self-diagnostic routine is performed only after the engine has been shut off. In some situations, the diagnostic function of both NOx sensors can be too sensitive when sampling the residual exhaust gases, leading to an erroneous fault being set. Unfavorable DDE software diagnostics
6407132018-11-13. Service bulletin. VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:FAN/MOTOR; ENGINE AND ENGINE COOLING. Service Action: Replace Blower Motor Regulator. The blower motor regulator has an internal fault; after starting the engine, there may be a delay of up to a minute before the blower motor comes on CAUSE Faulty blower motor regulator (output stage)
6407132018-11-13. Service bulletin. ENGINE AND ENGINE COOLING; VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:FAN/MOTOR; VISIBILITY. Service Action: Replace Blower Motor Regulator. The blower motor regulator has an internal fault; after starting the engine, there may be a delay of up to a minute before the blower motor comes on CAUSE Faulty blower motor regulator (output stage)
1802132018-11-13. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. "Exhaust Flap Actuator Is Loose. INFORMATION Covered under the terms of the BMW New Vehicle/SAV Limited Warranty Defect Code:18 12 03 39 00https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/159...2/5/2014 Page 2 of 2 Labor Operation:Labor Allowance:Refer to KSDReplacing exhaust flap actuator driveLabor operation code 18 12 081 is a Main labor operation. If you are using a Main labor code for another repair, use the Plus code labor operation 18 12 581 instead. Refer to KSD2 for the corresponding flat rate unit (FRU) allowance. Enter the Chassis Number, which consists of the last 7 digits of the Vehicle Identification Number (VIN). Click on the ""Search"" button, and then enter the applicable flat rate labor operation in the FR code field."
B1233142018-11-13. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING. Fault Code 1D2008 Stored in DME. The Service Engine Soon light is on. Fault Code 1D2008: Map thermostat: jammed open is stored in the DME. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up, the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat.
B1126152018-11-13. Service bulletin. POWER TRAIN; ENGINE. Delivery Stop: B58 Engine - Check Crankshaft Bearing Shells.A Delivery Stop has been issued on F30 and F32 certain vehicles produced from July 2015 (start of production) to December 2, 2015. These vehicles may have upper guide bearing shells that may exhibit wear at low mileage. There are 45 vehicles affected by this stop. For your convenience, attached you will find the list of affected VINs. This bulletin will be updated with repair instructions and warranty information when it becomes available. Affected vehicles can be identified with a ?Vehicle Comment? in DCS Warranty Vehicle Inquiry or ISPA Light with a specific description.
B6406132018-11-13. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING; EQUIPMENT:APPLIANCE:AIR CONDITIONER. A/C Cooling: Intermittent Reduction of Air Flow. Customer may complain of reduced air flow when the air conditioning system is operated for an extended time, usually longer than 30 minutes. INFORMATION Possibility of reproducing this situation is improved by the following conditions ? High outside ambient temperature ? High humidity Note: It is very difficult to duplicate this issue. The fault may be reproduced under the following conditions: ? Air-conditioning system switched on ? Driving Experience switch NOT set to Eco Pro ? Slower fan speeds ? Temperature setting below 68°F (20°C) ? Trip duration at least 30 minutes ? Outside temperature above 68°F (20°C) NOTE: After parking the vehicle or switching off the air-conditioning system for at least 20 minutes, the symptom disappears (ice melts off evaporator and puddles under the car from the A/C drains.). Evaporator starts to freeze up due to the position of the evaporator temperature sensor.
B1114152018-11-13. Service bulletin. ENGINE AND ENGINE COOLING. The plastic oil filter housing may fail and lead to an internal and/or external engine oil or coolant leak.
1215132018-11-13. Service bulletin. ENGINE. ?N20 and N26 Engine: Various VANOS System Faults Stored in DME. The Service Engine Soon lamp and Engine Malfunction warning are illuminated, and the vehicle has reduced power output. This situation can occur as a customer complaint, or after performing repairs to the engine valve train assembly. One or more of the following faults is stored in the DME. F10, F25, F30, F31 and F34: 131401 VANOS, exhaust, starting from cold: Non-adjustable 131501 VANOS, intake, starting from cold: Non-adjustable 131808 VANOS, exhaust, starting from cold: Position not reached 131908 VANOS, intake, starting from cold: Position not reached 130104 VANOS, intake, control fault, camshaft jammed 130304 VANOS, exhaust, control fault, camshaft jammed 130308 VANOS, exhaust, control fault, position not reached 130108 VANOS, intake, control fault, position not reached E84 and E89: 2D54 VANOS, exhaust, starting from cold: Non-adjustable 2D55 VANOS, intake, starting from cold: Non-adjustable 2D56 VANOS, exhaust, starting from cold: Position not reached 2D57 VANOS, intake, starting from cold: Position not reached 2D60 VANOS, exhaust, control fault, camshaft jammed 2D5A VANOS, intake, control fault, camshaft jammed 2D5B VANOS, intake, control fault, position not reached 2D61 VANOS, exhaust, control fault, position not reached If one of the applicable faults listed above is not stored in the DME fault memory then continue troubleshooting with the applicable test plan for the fault(s) stored. CAUSE This is due to a diagnostic programming error in the DME.
B1233142018-11-13. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING. Fault Code 1D2008 Stored in DME. The Service Engine Soon light is on. Fault Code 1D2008: Map thermostat: jammed open is stored in the DME. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up, the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat.
B1103152018-11-13. Service bulletin. ENGINE. N20 and N26 Engine: Oil Leaks from Cylinder Head Cover. There is an engine oil leakage under the vehicle, or the vehicle smells of engine oil. The cylinder head cover gasket is leaking engine oil due to loose retaining bolt(s).
1204152018-11-13. Service bulletin. ELECTRICAL SYSTEM; ENGINE. SUBJECT DME Internal and Valvetronic Faults Set at Cold Ambient Temperatures. The Service Engine Soon light (MIL) can be illuminated with the erroneous internal and Valvetronic faults stored in the DME. The MIL will only come on if the fault has been detected on two (or more) consecutive drive cycles. The following fault codes may be stored in the DME: E Seriesz 36AE - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 2DE2 - Valvetronic, actuation, voltage phase: Line disconnection z 2DE3 - Valvetronic, actuation, volt phase: Line disconnection z 2DE4 - Valvetronic, actuation, volt phase: Line disconnection F Seriesz 1F0905 - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 135B10 - Valvetronic, actuation, voltage phase: Line disconnection z 135B11 - Valvetronic, actuation, volt phase: Line disconnection z 135B12 - Valvetronic, actuation, volt phase: Line disconnection Engine performance and driving characteristics are not affected. DME software diagnostic sensitivity.
B1209162018-11-13. Service bulletin. ENGINE AND ENGINE COOLING. N20 - The Service Engine Soon Light is On with DME Fault 118602 Stored. The Service Engine Soon light is on (MIL) with only the following oxygen sensor fault stored. 118602 - Oxygen sensor before catalytic converter, fine mixture control: exhaust gas after catalytic converter too lean CAUSE An actual engine related problem and/or DME software diagnostic.
B1231152018-11-05. Service bulletin. EQUIPMENT; ENGINE. """Low Oil Warning Indicator Light"" Comes on After Extended Driving. After approximately 2-4 hours of driving on the highway at 80 mph, and at an engine speed of around 2200-2500 rpm with an average load, the ""low oil"" warning indicator light illuminates yellow and the following check control (CC) message (ID 27) displays: ""Top up 1 L of engine oil"". Also, fault code: 297200 - oil level (Layer_MOELNIV): Engine oil level too low, may be stored in the DDE CAUSE DDE software error"
B1116152018-11-05. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. ?N20 and N26 engine: Smoke from Exhaust when Starting a Cold Engine. When starting a cold engine, blue smoke can be seen emitting from the exhaust tailpipe for approximately 10-20 seconds. No turbo charger boost faults are stored and no drivability issues can be detected. Engine oil leakage into the induction system and/or the turbo charger assembly.
1221142018-11-05. Service bulletin. ENGINE; ELECTRICAL SYSTEM. SI B12 21 14February 2015 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 21 14 dated December 2014. designates changes to this revision SUBJECT Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: z FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.