Service bulletins for the 2006 Bentley Continental
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
123 on file from NHTSA, as of 2026-10-19.
By type
By component
| 2056407.4 | 2022-12-08. Service bulletin. STEERING; SUSPENSION. Running Gear - Noise Identification Customer Statement: -Noise complaint from the suspension and/or steering |
|---|---|
| 2051562.10 | 2022-12-08. Service bulletin. ELECTRICAL SYSTEM. 12 Volt - Battery Test Instruction Technical Background: -For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the measure of this section of this TPI. |
| 2051187.7 | 2022-11-08. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Poor Engine Running Complaints (Misfires) Petrol Engines Only Customer Statement: -Poor engine running, reduced power, engine warning lamp illuminated. |
| 2051562.9 | 2022-11-08. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. 12 Volt- Battery Condition Checks. Technical background For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI. |
| 2053492/8 | 2022-10-07. Service bulletin. SUSPENSION. Air spring fault finding Customer Statement: -The front and/or rear suspension appears to have dropped Technical Background: -Bentley vehicles which are applicable to this TPI are fitted with air springs as part of the suspension system. Should air leak from the air spring dampers, this will cause the suspension to drop. However, the dropping of the suspension does not necessarily mean that the air spring is faulty. -The Measure section of this TPI describes how and where to check for air leaks on the front and rear air springs, the air supply unit, pipes, valve unit and air reservoirs. This includes potential air leak points on the air spring dampers and also the locations of an air leak that can be repaired without the need to replace an air spring damper. |
| 2051562/8 | 2021-11-04. Service bulletin. ELECTRICAL SYSTEM. 12 Volt - Battery condition checks. Customer statement / workshop findings: 12 Volt Battery test instruction Technical background: For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI |
| 2053492/7 | 2021-10-07. Service bulletin. SUSPENSION. Air spring fault finding. Customer statement / workshop findings: The front and/or rear suspension appears to have dropped. Technical background: The list of Bentley vehicles below are fitted with air springs as part of the suspension system. Should air leak from the air springs, this will cause the suspension to drop. However, the dropping of the suspension does not necessarily mean that the air spring is faulty. The Measure section of this TPI describes how and where to check for air leaks on the front and rear air springs, the air pump compressor, pipes, valve unit and air reservoirs. This includes potential air leak points on the air springs and also the locations of an air leak that can be repaired without the need to replace an air spring. |
| 2056582/4 | 2021-10-06. Service bulletin. STRUCTURE. Interior trim - Creak and rattle - Noise identification Customer statement: Noise complaint from the interior Workshop findings: The noise can be reproduced and clearly assigned to the interior Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work |
| 2052785/6 | 2021-10-05. Service bulletin. SERVICE BRAKES, HYDRAULIC. Brake noise identification. Customer statement / workshop findings: Noise complaint from the braking system. Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Technical background Brake noises can be attributed to many causes. Eight of the most common causes are: - Brake discs or pads are close to their wear limit. - New brake pads and/or discs have not been properly bedded in after installation. - Aftermarket pads or discs are installed. - There is debris such as small stones, grit, road salt or sand between the brake disc and pad. - Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time (Figure 1). |
| 2051562/7 | 2021-10-05. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY; ELECTRICAL SYSTEM. 12 Volt - Battery condition checks. Customer statement / workshop findings: 12 Volt Battery test instruction Technical background: For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI |
| 2036678/4 | 2021-10-05. Service bulletin. ELECTRICAL SYSTEM. Speaker Replacement - Diagnostic checks. Customer statement / workshop findings: Audio output from speakers is distorted Technical background: There have been instances where door speakers have been changed under warranty for the complaint of sound distortion, yet when tested by ourselves and the supplier, no fault could be found with the returned unit. Production change: All speakers are subjected to a dynamic test and the individual results recorded for future reference |
| 2051187/6 | 2021-10-05. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Poor Engine Running Complaints (Misfires) Petrol Engines Only. Customer statement / workshop findings: Poor engine running, reduced power, engine warning lamp illuminated. Technical background: Technical Product Information (TPI) to assist Retailers when diagnosing poor engine running or misfire. Measure: The following TPI should be carried out sequentially to ensure the root cause and analysis of the concern are identified without unnecessary work or repetitive actions taking place. |
| 2033864/6 | 2021-10-04. Service bulletin. WHEELS. Customer statement / workshop findings: Unable to remove Accessory valve caps, Figure 1 shows an example of the caps. Technical background: We have observed instances where the caps have been difficult to remove once fitted, the issue is caused by corrosion. The valve stem itself is made from aluminium and the accessory valve caps are chromium plated brass, it is possible under certain environmental conditions, particularly winter road salt, for corrosion to take place between these dissimilar metals. Measure: The solution is to apply a thin smear of silicon-based grease, such as Dow Corning high vacuum grease, to the external threads of the valve stem prior to fitting the accessory valve cap. Grease should be applied any time the cap is removed and grease is not evident |
| 2056407/3 | 2021-10-04. Service bulletin. STEERING; SUSPENSION. Running gear - Noise identification. Customer statement: Noise complaint from the suspension and/or steering Workshop findings: The noise can be reproduced and clearly assigned to the suspension system from either of the axles And/or The noise can be reproduced and clearly assigned to the steering system |
| 2063025/1 | 2021-05-06. Service bulletin. ELECTRICAL SYSTEM; STRUCTURE; LATCHES/LOCKS/LINKAGES. Powered Boot fails to operate due to faulty motors - Replacement motors unavailable to obtain Customer statement / workshop findings: Powered boot fails to operate due to faulty motors, replacement motors are unavailable to obtain Technical background: Refer to the Measure section of this TPI to allow the boot to be used in manual mode |
| 2061195/1 | 2020-12-02. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Telephone Functionality Complaint - Minimum Standards Required For Analysis Of Concerns. Customer statement / workshop findings: The feedback method within this TPI is required should a complaint of telephone functionality and/or quality be reported. Technical background: The minimum standards check list document within the Measure section is required to capture an accurate description of customer telephone issues. |
| 2051562/6 | 2020-12-02. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; ELECTRICAL SYSTEM. All Models - 12 Volt Battery condition checks. Technical background For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI. |
| 2058173/2 | 2020-11-07. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Electrical switch replacement guidelines. Customer statement/workshop findings: Electrical switch suspected as defective This TPI is not applicable to suspected faulty control units or any component related to the passive restraint system in particular the airbag system Technical background: Prior to replacing an electrical switch refer to the Measure section of this TPI |
| 2059884/1 | 2020-11-07. Service bulletin. LATCHES/LOCKS/LINKAGES; STRUCTURE; ELECTRICAL SYSTEM. Continental Series and Flying Spur - Luggage Compartment Lid - Check and Setting Guide. Customer statement / workshop findings: Luggage Compartment Lid (Boot Lid) has sporadic functionality, fails to latch when closing, bounces back when closing or fails to open or close fully. Technical background: This Technical Product Information (TPI) document has been developed to resolve various boot lid concerns, it provides a series of checks and updates to ensure robust boot lid operation. It is important the TPI is followed exactly to ensure maximum benefit. |
| 2052785/5 | 2020-09-05. Service bulletin. SERVICE BRAKES, HYDRAULIC. Brake noise identification. Customer statement: Noise complaint from the braking system. Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Technical Background: Brake noises can be attributed to many causes. Eight of the most common causes are: 1. Brake discs or pads are close to their wear limit. 2. New brake pads and/or discs have not been properly bedded in after installation. 3. Aftermarket pads or discs are installed. 4. There is debris such as small stones, grit, road salt or sand between the brake disc and pad. 5. Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time (Figure 1). |
| 2056582/3 | 2020-08-05. Service bulletin. STRUCTURE. Interior trim - Creak and rattle - Noise identification. Customer statement / workshop findings: Noise complaint from the interior Workshop findings: The noise can be reproduced and clearly assigned to the interior Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work |
| 2053492/6 | 2020-08-05. Service bulletin. SUSPENSION:REAR:SPRINGS. Air spring fault finding. Customer statement / workshop findings: The front and/or rear suspension appears to have dropped. Technical background: The list of Bentley vehicles below are fitted with air springs as part of the suspension system. Should air leak from the air springs, this will cause the suspension to drop. However, the dropping of the suspension does not necessarily mean that the air spring is faulty. TheMeasure section of this TPI describes how and where to check for air leaks on the front and rear air springs, the air pump compressor, pipes, valve unit and air reservoirs. This includes potential air leak points on the air springs and also the locations of an air leak that can be repaired without the need to replace an air spring. These checks should be carried out in conjunction with the Elsapro procedure Air suspension: To check with the use of the special tool Air suspension leak tester VAS 751 001 shown in the image below as item ( 1). Refer to Elsapro, Repair Group 43, Air suspension To check. |
| 2036869/1 | 2020-07-28. Service bulletin. ENGINE AND ENGINE COOLING. Continental GT - Continental Flying Spur - Replacement engine identification (SC14/19) Technical background: The engine fitted to this vehicle is a service replacement engine, in order to allow the engine to be identified as a service replacement engine for future parts and workshop manual information the instructions within this procedure must be followed. The service replacement engine is based on a 2012 model year W12 engine. Remedy: This campaign must be carried out on all applicable vehicles within the specific VIN range to ensure all affected vehicles are checked and repaired as detailed within the onward instructions. |
| 2058173/1 | 2020-02-08. Service bulletin. ELECTRICAL SYSTEM. Electrical switch replacement guidelines Customer statement / workshop findings: Electrical switch suspected as defective This TPI is not applicable to suspected faulty control units or any component related to the passive restraint system in particular the airbag system Technical background: Prior to replacing an electrical switch refer to the Measure section of this TPI |
| 2033745/2 | 2020-01-17. Service bulletin. LATCHES/LOCKS/LINKAGES; ELECTRICAL SYSTEM. Bentley Continental Series - Power boot close switch - Correct diagnosis Customer statement / workshop findings: Boot lid does not attempt to power close when the boot close switch (located on the inside of the boot lid) is pressed. Technical background: In the event the power boot does not attempt to close when the boot close switch is pressed please check the applicability of the model and VIN shown in the Production change section of this TPI before commencing. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.