Service bulletins for the 2020 Bentley Bentayga
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
753 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Electrical system are shown. Show all
| 2066714/1 | 2022-06-03. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Bentayga Hybrid - DTC's P0C5C00 - P0C5200 - P0A2D00 evident within address 51 - Drive Motor Control Module. Customer statement / workshop findings: Engine warning light within the Driver Instrument Panel (DIP) The following DTCs are evident within address 51 - Electric Drive Motor for: Workshop findings One or a combination of the following DTCs are evident within address 51 - Electric Drive Motor - P0C5C00: Drive Motor A Position Sensor Circuit B Low And/or - P0C5200: Drive Motor A Position Sensor Circuit A Low And/or - P0A2D00: Drive Motor A Temperature Sensor Circuit High Technical background: In the event the symptoms described are evident the operative should refer to the instructions within the Measure section of this TPI. |
|---|---|
| 2059027/4 | 2022-06-03. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Customer statement / workshop findings: Various warning messages on Driver Instrument Panel (DIP) Unable to select EV Drive mode. Fault codes stored in multiple diagnostic addresses for Data-bus errors. Diagnostic Trouble Codes (DTCs) P0C5*00 - Drive motor A faults - stored in address 51 - Drive Motor Control Module . Technical background: DTCs - P0C5*00 - may be set within address 51 - Drive Motor Control Module If the transmission 12 Volt harness becomes damaged or there are unsatisfactory electrical connections within the connector for Drive Motor Position Sensor. The stored DTCs would indicate an issue with Drive motor A, however, prior to carrying out any fault diagnosis use the information within the Measure section of this document as an initial check. |
| 2055036/5 | 2022-06-02. Service bulletin. ELECTRICAL SYSTEM. My Bentley - Connected services. Customer statement / workshop findings: Complaints relating to My Bentley connected services. Technical background: Most queries and complaints regarding My Bentley connected services can be resolved by contacting My Bentley Support rather than raising a DISS technical query. My Bentley support have access to additional admin tools and systems to help resolve any queries; and also have the ability to raise DISS technical queries if required. |
| 2066591/1 | 2022-05-06. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING. DTC P263500 with symptom code -10061 - Noise from within the fuel tank. Customer statement - Engine warning light illuminated within the DIP And/or - Drive system fault warning within the DIP (Figure 1) Workshop findings - DTC P263500 - Fuel Pump A Low Flow/Performance evident within diagnostic address 01 and/or 11 - With symptom code 10061 - Noise from within the fuel tank (fuel pump) - Refer to the video on the Bentley hub referencing TPI 2066591/- Technical background Prior to conducting the instructions within this TPI, the retailer must check and confirm there are no other issues evident with the vehicle for example: - Misfire related DTCs - Low pressure fuel DTCs other than DTC P263500 - Damaged fuel hoses and pipes - Examine all hoses and pipes external of the fuel tank - Fuel leaks. |
| 2065398/2 | 2022-05-06. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. W12 TSI - Engine MIL light illuminated with numerous DTC's within 0001 including - P032700 and/or P033200. Customer statement: - MIL light displayed - Engine not refined when running Workshop findings The two most common DTCs are as follows: - P032700 - Knock sensor 2 Circuit Low input - address 01 (Engine control module 1) - P033200 - Knock sensor 1 Circuit Low input - address 01 (Engine control module 1) Technical background: In the event the symptoms and/or DTCs are evident the operative should refer to the instructions within the Measure section. |
| 2062080/5 | 2022-04-08. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM). Bentayga V8 Kovomo and V6 (Hybrid) - Fuel Pressure Regulation. Customer statement / workshop findings: Check Engine Lamp illuminated within the Driver Instrument Panel (DIP) with one or multiple DTCs as detailed below: -P310B00 with symptom code 2636 - Low Fuel Pressure Regulation Low Fuel Pressure Regulation -P014800 Fuel Deliver Error -P019100 Fuel Rail pressure Sensor A Circuit Range/Performance Misfire DTCs There may be multiple DTCs and symptoms present due to fuel pressure regulation or fuel supply issues, Measure: Check Engine Lamp Illumination with DTC P310B00 and symptom code 2636 - Engine Running Concerns, Fuel system issues -P310B00 Low Fuel Pressure Regulation symptom code 2636 -P014800 Fuel Deliver Error -P019100 Fuel Rail pressure Sensor A Circuit Range/Performance Misfire DTCs 1) If not already done, raise a DISS query. 2) Check Low fuel pressure, specified value and Fuel low pressure, actual value within the fault memory, refer to ECU 01 Engine Control Module 1 - From Extended ambient conditions note the values of the Low fuel pressure, specified value and Fuel low pressure, actual value as shown in Figure 1. |
| 2063657/2 | 2022-04-07. Service bulletin. ENGINE AND ENGINE COOLING; FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM. P245000 - EVAP System Switching Valve "A" Performance/Stuck Open DTC logged - Bentayga V8 Kovomo. Customer Statement: Emission control system warning light illuminated within the DIP (Figure 1) Figure 1 Workshop findings DTC P245000 - EVAP System Switching Valve "A" Performance/Stuck Open - With symptom code 11952. Measure: Fuel System vapours are extremely flammable. Please refer to the Repair manual "Fuel system - Safety precautions" before commencing with any fuel system procedures 1) Referring to the applicable wiring diagram conduct a wiring integrity check of the Leak Detection Pump wiring circuit and connectors 2) Perform a smoke test of the leak detection system - Monitor for any leaks 3) If no faults were found - Refer to Rep.Gr 20 - Replace the leak detection pump (V144) 4) Inspect the LDP for impact damage when extracted, the operative must provide feedback and photographic evidence (see example shown in Figure 2) via a new or existing DISS query |
| 2066497/1 | 2022-04-07. Service bulletin. ELECTRICAL SYSTEM. Bentayga Hybrid - Unable to charge the high voltage battery or charging starts and then stops. Customer statement: Unable to charge the high voltage battery, or charging starts and then stops. Workshop findings: The following DTCs are evident within the high voltage battery charger control module (Diagnostic address C6) - P33EC00: External plug in charge socket A electrical error - P31CB00: Immediate upload button Stuck Closed - P168F00: System malfunction And/or The following DTC is evident within hybrid battery management control module (Diagnostic address 8C) - P0E5E00: Battery charger control module processor performance. Measure: 1) Referring to Rep.Gr 93 - Carry out an Inspection and classification of the Hybrid battery unit AX1 |
| 2066561/1 | 2022-04-07. Service bulletin. COMMUNICATION; ELECTRICAL SYSTEM. High Voltage battery Charger communication DTC U113900 - Stored in address 17 - Dashboard. Customer statement / workshop findings: The following DTC is evident within diagnostic address 17 - Dashboard - High Voltage battery Charger communication DTC U113900. Measure: Should no other issues be evident with the High Voltage charging system, DTC U113900 stored within address 17 can be ignored Technical product information High Voltage battery Charger communication DTC U113900 - Stored in address 17 - Dashboard Transaction No.: 2066561/1 |
| 2065715/1 | 2022-04-07. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM); ELECTRICAL SYSTEM. Bentayga Hybrid - Emission control system warning lamp illuminated within the DIP - Potential wiring clash condition. Customer statement / workshop findings: - Emission control system warning lamp illuminated (Figure 1) within the Driver Information Panel (DIP) Figure 1 Workshop findings - Various/numerous open circuit DTCs evident within the Engine control unit (Address 001). Measure: VERY IMPORTANT: Hybrid vehicles use a High voltage system and MUST only be worked on by suitably qualified personnel 1) Using the applicable wiring diagram, conduct wiring integrity checks to confirm the wire(s) which are damaged/chaffed TIP: Overlaying the suspected damaged wiring can be conducted to confirm the issue, the overlayed wiring MUST NOT be left in place, all damaged wiring MUST be repaired as per all Elsa pro guidelines 2) Referring to Rep.Gr 97 - Repair the damaged wire(s) Technical product information Bentayga Hybrid - Emission control system warning lamp illuminated within the DIP - Potential wiring clash condition Transaction No.: 2065715/1 3) Remove all sharp edges which could damage the main wiring harness 4) Reposition and secure the main wiring harness. |
| 2065697/1 | 2022-04-07. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE; ELECTRICAL SYSTEM. Bentayga Hybrid - Emission control system warning lamp illuminated within the DIP - Open circuit DTC's evident. Customer statement: - Emission control system warning lamp illuminated (Figure 1) within the Driver Information Panel (DIP) Figure 1 Workshop findings - Various/numerous open circuit DTCs evident within the Engine control unit (Address 001) - Fuse 6 (SA fuseboard) in some cases could be blown. Measure: VERY IMPORTANT: Hybrid vehicles use a High voltage system and MUST only be worked on by suitably qualified personnel 1) Using the applicable wiring diagram, Conduct a wiring integrity check to confirm the wire(s) which are damaged/chaffed TIP: Overlaying the suspected damaged wiring may be carried out to confirm the actual issue, the overlayed wiring MUST NOT be left in place, all damaged wiring MUST be repaired as per all Elsa pro guidelines 2) Using the applicable repair manual Rep.Gr - Gain access to the main body harness damaged wiring - Take clear photographs of the issue (once identified) the photographs should be saved as they are required to uploaded to a non-technical DISS query after the repair has been conducted. |
| 2066502/1 | 2022-04-07. Service bulletin. STRUCTURE; ELECTRICAL SYSTEM. Charging starts and stops when using a public charging unit. Customer statement / workshop findings: When using a public charging unit to charge the high voltage battery, charging starts and is then interrupted/stops Workshop findings The following DTC is also evident: P33E800: Charge socket A, charge connector lock mechanical malfunction passive/sporadic. Measure: 1) Referring to Rep.Gr 93 - Carry out an Inspection and classification of the Hybrid battery unit AX1 VERY IMPORTANT: In the event that the classification result of the battery is Normal the operative should conduct the remaining steps of this TPI from step 2 However If the classification result of the battery is either Danger or Warning then move the car to the quarantine area and raise a DISS immediately, the operative MUST NOT continue with any other work unless instructed via the open DISS query 2) Check the operation of the charging system using the customers and the retailers own charging equipment 3) Run a full diagnostic log and check if the DTC within the Technical background section are evident. |
| 2066246/1 | 2022-04-07. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Bentayga/New Flying Spur - DTC P0C4A00 Hybrid/EV Battery Pack Coolant Pump A Control Performance within address 8C. Customer statement / workshop findings: - Speed limitation noticeable when driving in EV mode (Restricting the vehicle speed to approximately 30mph/48kph) - Refer also to the video on the Bentley Hub referencing TPI 2066246/- - No other warnings are evident within the DIP Workshop findings - DTC P0C4A00 Hybrid/EV Battery Pack Coolant Pump "A" Control Performance within Address 8C Battery Regulation Control Unit. Measure: 1) Referring to Rep.Gr 93 - Carry out an Inspection and classification of the Hybrid battery unit AX1. |
| 2059392/2 | 2022-04-07. Service bulletin. ELECTRICAL SYSTEM. Bentayga - PDC system not working or PDC system false detection. Customer statement / workshop findings: - PDC system not working or PDC system false detection - Warning evident within the DIP Workshop findings: - Parking aid sensor Range/Performance DTCs evident within numerous control units Technical background: Refer to the Measure section of this TPI |
| 2066236/1 | 2022-04-06. Service bulletin. EXTERIOR LIGHTING; ELECTRICAL SYSTEM. Unintended sounding of the Alarm siren - Following activation of the ignition or whilst the vehicle is left standing. Customer statement / workshop findings: Unintended sounding of the alarm siren following activation of the ignition Or Unintended sounding of the alarm siren whilst the vehicle is left standing Workshop findings. The following DTCs could also be evident within diagnostic address 0046 and/or 00BB and/or 00BC - B131DF5: alarm system siren supply voltage lower limit value less than - B131D29: sirens / alarm horn for anti-theft warning system Range/Performance - B131D29: anti-theft alarm system siren / alarm horn signal, not valid Technical background: In the event the symptom(s) described are evident, please refer to the instructions within the Measure section of this TPI |
| 2058484/6 | 2022-03-02. Service bulletin. FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Bentayga V8 Kovomo - DTC P310B00 with Symptom Code 2638 - Check Engine Lamp - Fuel Pressure Regulation. Customer statement / workshop findings: Check Engine Lamp illuminated within the Driver Instrument Panel (DIP) in conjunction with the DTC as detailed below: - P310B00 with symptom code 2638 - Low Fuel Pressure Regulation There may be multiple DTCs and symptoms present due to fuel pressure regulation or fuel supply issues. Measure: Check Engine Lamp Illumination with DTC P310B00 and symptom code 2638 1) For vehicles that only have the symptoms: - Check Engine Lamp Illumination with DTC P310B00 and symptom code 2638 with an Adaption of Fuel Pump (FP) figure of minus 100 to minus 200 kPa Figure 1 - the Fuel Delivery Module within the fuel tank should be replaced Figure 2 - Refer to Repair Group 20 Fuel supply, gas operation / 4.0L V8 TSI / Fuel pump, fuel level sensors, and jet pump (RH) To remove and fit. |
| 2062080/4 | 2022-03-02. Service bulletin. ENGINE AND ENGINE COOLING; FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM. Bentayga V8 Kovomo - Fuel Pressure Regulation. Customer statement / workshop findings: Check Engine Lamp illuminated within the Driver Instrument Panel (DIP) with one or multiple DTCs as detailed below: - P310B00 with symptom code 2636 - Low Fuel Pressure Regulation Low Fuel Pressure Regulation - P014800 Fuel Deliver Error - P019100 Fuel Rail pressure Sensor A Circuit Range/Performance - Misfire DTCs There may be multiple DTCs and symptoms present due to fuel pressure regulation or fuel supply issues. Measure: Check Engine Lamp Illumination with DTC P310B00 and symptom code 2636 - Engine Running Concerns, Fuel system issues - P310B00 Low Fuel Pressure Regulation symptom code 2636 - P014800 Fuel Deliver Error - P019100 Fuel Rail pressure Sensor A Circuit Range/Performance - Misfire DTCs 1) If not already done, raise a DISS query. 2) Check Low fuel pressure, specified value and Fuel low pressure, actual value within the fault memory, refer to ECU 01 Engine Control Module 1 - From Extended ambient conditions note the values of the Low fuel pressure, specified value and Fuel low pressure, actual value as shown in Figure 1. |
| 2065919/1 | 2022-03-02. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Water leaking from mechanical water pump - Low coolant level warning displayed - W12 TSI. Workshop findings: - Coolant leaking from the mechanical coolant pump And/or - Low coolant level warning displayed Technical background: The operative MUST ensure the instructions within the Measure section are followed, the instructions differ slightly depending on the part number of the mechanical coolant pump (B or C suffix). |
| 2066040/1 | 2022-03-02. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Oil leak from the oil separator/breather connection - Intake manifold whistle - Emission control warning within the DIP. Customer statement / workshop findings: - Emission control warning within the DIP And/or - Whistling noise(s) from the Inlet manifold Workshop findings: Oil leak between the oil separator tank and the Bank 1 breather line connection (Figure 1) NOTE: Oil leak detection spray is evident within Figure1, the use of detection spray in the example shown highlights the location of the leak. Measure: 1) Referring to Rep.Gr 17 - Gain access to the oil separator tank 2) Referring to Figure 2 - Replace the following parts and all associated parts as detailed within the applicable Rep.Gr and the ETKA parts catalogue |
| 2051045/5 | 2022-03-02. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Night vision camera - Washer jet leaking. Customer statement / workshop findings: Washer fluid dripping/leaking from the night vision camera washer jet Technical background: Please note: The photographs shown within this TPI are based on a New Continental GT/C vehicle however the process is similar regardless of vehicle type Referring to Figure 1 - In the event the afore mentioned symptom is evident the operative should refer to the Measure section of this TPI to replace the night vision washer jet (short link hose -Circled) which connects the night vision camera washer jet (A) to the washer jet supply hose connector (B) Measure: 1) Referring to Rep.Gr 63 Remove the front bumper lower inner grilles 2) Disconnect the hose from the night vision camera as shown in Figures 2 and 3 Please note: Washer fluid may leak once the hose is disconnected - Ensure a suitable container is used to collect the fluid, all fluid MUST be discarded as per all local environmental guidelines |
| 2058423/7 | 2022-03-01. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. New Continental GT / GTC, New Flying Spur and Bentayga - Low Oil Pressure Warning During Early Vehicle Life. Customer statement / workshop findings: Warning on the Driver Instrument Panel (DIP) - Oil pressure too low DTCs relating to oil pressure may also be stored within the Master ECU. Diagnostic Trouble Codes (DTC) P052400: Engine Oil Pressure Too Low and/or P15AA00: Engine oil pressure - Lower limit not reached stored in the Master Engine Control Unit (ECU). Measure VERY IMPORTANT: Prior to conducting the onward instructions, the following symptoms MUST be evident - Warning on Driver Instrument Panel (DIP) Oil pressure too low And/or - Diagnostic Trouble Codes (DTC) P052400: Engine Oil Pressure Too Low and/or P15AA00: Engine oil pressure - Lower limit not reached stored in the Master Engine Control Unit (ECU) Should any of the afore mentioned not be evident and the symptoms cannot be reproduced. No further action should be taken unless the issue can be reproduced or demonstrated by the customer. In the event the symptom/s are evident please conduct the onward Diagnosis Instructions |
| 2064776/3 | 2022-02-04. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. V8 Kovomo - Engine misfires - Engine management light illuminated within the DIP. Customer statement / workshop findings - Engine misfiring - Engine running rough (not refined) - Engine misfire DTCs evident - Engine management light illuminated within the DIP - Knocking noise from the cylinder head (NOTE: The noise can be evident on either bank) Measure VERY IMPORTANT: Before continuing with the onward instructions the operative should confirm if the following VIN applicable Service Campaign is listed within Elsa pro - EC24 - V8 Kovomo - New Continental GT/GTC and New Flying Spur - Valve spring replacement (SC21/41) Or - EC25 - V8 Kovomo - Bentayga - Valve spring replacement (SC21/42) |
| 2064776/2 | 2022-01-08. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. V8 Kovomo - Engine misfires - Engine management light illuminated within the DIP. Customer statement / workshop findings: - Engine misfiring - Engine running rough (not refined) - Engine misfire DTC’s evident - Engine management light illuminated within the DIP - Knocking noise from the cylinder head (NOTE: The noise can be evident on either bank) IMPORTANT: The symptoms described are typically evident during early life stages of vehicle use (between 100Km and 250Km) Technical background Refer to the Measure section of this TPI in the event the symptoms are as described |
| 2059612/3 | 2022-01-08. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Bentayga Hybrid and New Flying Spur Hybrid - Home Charging Unit PIN code. Customer statement / workshop findings: Bentley Home Charging Unit - Unable to recollect Personal Identification Number (PIN). Unable to charge High Voltage Battery with Bentley Home Charging Unit. Technical background: The Bentley Home Charging Unit can be protected from unauthorised use by creating a four-digit PIN. If the PIN authorisation function is activated it has to be entered in the Home Charging Unit before it is used to charge the High Voltage Battery. If a Customer forgets the assigned PIN it will not be possible to unlock the Bentley Home Charging Unit. Follow the steps within the 'Measure' section to reset the PIN. |
| 2057470/3 | 2022-01-08. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:WIRELESS CHARGER/CRADLE. Bentayga Hybrid and New Flying Spur - Bentley Home Charging Unit - Not Functioning. Customer statement / workshop findings: High voltage system - Bentley Home Charging Unit (Low version) does not function, the following indicator lights are illuminated in red. Bentley Home Charging Unit is connected to an un-earthed power supply. Technical background: Certain mains power supplies use an un-earthed infrastructure, in these specific circumstances it is necessary to deactivate Protective Earth (PE) conductor monitoring on the Bentley Home Charging Unit. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.