Service bulletins for the 2013 Audi S8
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
809 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Engine are shown. Show all
| A011257 2028344- | 2017-11-08. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR; ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 01 number 12-51 dated July 18, 2012. Noises/inconsistent engine operation after cold start during the catalyst heating phase. The customer may interpret this engine roughness as misfiring. To comply with the legal requirements on exhaust gas emissions according to the LEV-1 and LEV-2 standards, a high exhaust gas quality must be ensured. The necessary catalyst only operates at a temperature over 300°C (572°F). To achieve this, the catalyst is heated up. The catalyst heating phase is achieved by a late ignition angles and by introducing additional fresh air to the exhaust valves (secondary air system). Late ignition angles make sure that the exhaust gas from the cylinders has a higher temperature. This exhaust gas includes fuel that is un-burnt, and was deliberately injected into great quantities. The secondary air system adds fresh air to the exhaust gas as it leaves the cylinder and the extra fuel is burnt. As a result, the temperature of the exhaust gas and of the catalyst increases quickly. The afterburning in the exhaust manifold before catalyst changes the sound characteristic of the engine. This heating-up of the catalyst, including afterburning, is normal and has no effect on the service life of the engine. During this catalyst heating phase the engine has increased idle speed, may have increased vibrations, and a different sound characteristic. Depending on conditions the time of the catalyst heating phase varies. |
|---|---|
| A001242 2030428- | 2017-11-08. Service bulletin. ENGINE; POWER TRAIN. Supersedes Technical Service Bulletin Group 00 number 12-37 dated August 13, 2012. If an all-new 2013 Audi A8 4.0T, S6, S7 and S8 arrives at an Audi dealership and requires diagnosis or repair, a Repair Authorization must be obtained. A Technical Assistance Center (TAC) ticket must be created for Engine and Transmission concerns only, prior to any repairs. Routine maintenance and PDI do not require prior authorization or a Technical Assistance Center (TAC) ticket. These procedures are mandatory until further notice. Warranty repairs without repair authorization via a TAC contact will not be reimbursed. |
| A001463 2033576- | 2017-11-08. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Supersedes Technical Service Bulletin Group 00 number 13-49 dated May 14, 2013. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage. |
| A191450 2025303- | 2017-11-08. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 19 number 13-41 dated June 20, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service. |
| A271423 2036392- | 2017-11-08. Service bulletin. ENGINE; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 27 number 14-22 dated April 21, 2014. Vibrations are felt at 1000 rpm and 3000 rpm. DTCs may be stored in the subframe mount control module. The basic settings of the active engine mounts in the subframe mount control module, J931, are deactivated when work is done on either of the vehicle electrical system control modules. As a result, the vehicle vibrates or judders when cylinders are actively switched off. |
| A191447 2036167- | 2017-11-08. Service bulletin. ENGINE AND ENGINE COOLING. The low coolant level light is illuminated. The coolant level is too low. A black crust is visible on the turbocharger coolant lines. There may be slow coolant loss from the connections of the coolant feed pipe and coolant return pipe. High temperatures cause the coolant to become encrusted on the connection flange of the turbocharger. |
| A011461 2035235- | 2017-11-08. Service bulletin. ENGINE; POWER TRAIN. Supersedes Technical Service Bulletin Group 01 number 13-36 dated October 9, 2013. The customer reports that the engine warning light illuminates sporadically. The engine may have reduced performance without significant loss of power or stalling. Noise is heard coming from the engine compartment, specifically from the High Pressure Fuel Pumps 2. DTCs are stored in the ECM. |
| Update Bulletin | 2017-11-03. Service bulletin. ENGINE; STRUCTURE. A quality package has been defined for Audi vehicles with 4.0L TFSI engine manufactured within a specific period. This Update is in effect until removed. Procedure is valid only for vehicles that show the 19J1 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicle must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. A quality package has been defined for Audi vehicles with 4.0L TFSI engine manufactured within a specific period. |
| Reference-Oil Ca | 2017-11-03. Service bulletin. ENGINE; EQUIPMENT; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This document contains the Audi oil capacity chart. |
| A871346 2035582- | 2017-11-03. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; ENGINE AND ENGINE COOLING. The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented. |
| Update Bulletin- | 2017-10-31. Service bulletin. ENGINE AND ENGINE COOLING. A quality package has been defined for Audi vehicles with 4.0L TFSI engine manufactured within a specific period. This Update is in effect until removed. Procedure is valid only for vehicles that show the 19J1 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicle must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. quality package has been defined for Audi vehicles with 4.0L TFSI engine manufactured within a specific period. |
| A101310 2018288- | 2017-10-31. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 10 number 10-02 dated September 14, 2010. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the vehicle's engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these pieces are not removed prior to the installation and operation of the replacement engine, the pieces may be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage. |
| A011336 2035235- | 2017-10-31. Service bulletin. FUEL SYSTEM, OTHER:DELIVERY:FUEL PUMP; ENGINE. The customer reports that the engine warning light illuminates sporadically. The engine may have reduced performance without significant loss of power or stalling. Noise is heard coming from the engine compartment, specifically from the High Pressure Fuel Pumps 2. DTCs are stored in the engine control module (ECM). The fuel metering valve of the high-pressure fuel pump is controlled by a specific on/off ratio. If there is a low system voltage, the on/off ratio may not be enough to keep the fuel metering valve constant in all areas. In such a situation, the fuel metering valve is deactivated and the high-pressure fuel pump switches to full supply mode. Because the increased rail pressure does not match the respective driving situation, the DTC appears. |
| Executive Servic | 2017-10-27. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN; STEERING:HYDRAULIC POWER ASSIST:POWER STEERING FLUID; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; SERVICE BRAKES, HYDRAULIC:FLUID. This document contains a fluid capacity chart as well as a chart that contains the parts and part numbers needed for service. |
| A191560 2036167- | 2017-10-27. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 19 number 14-47 dated January 31, 2014. The low coolant level light is illuminated. The coolant level is too low. A black crust is visible on the turbocharger coolant lines. There may be slow coolant loss from the connections of the coolant feed pipe and coolant return pipe. High temperatures cause the coolant to become encrusted on the connection flange of the turbocharger. |
| A171563 2038129- | 2017-10-27. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 17 number 14-53 dated November 7, 2014. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual. |
| A011524 2040491- | 2017-10-25. Service bulletin. ENGINE AND ENGINE COOLING. The MIL is on. "Coolant System: Fault Turn Off Engine" and the coolant symbol appears in the information panel. DTC P1B1C00 is stored in the ECM. |
| Campaign Circula | 2017-10-25. Service bulletin. ENGINE AND ENGINE COOLING. The oil filter bypass valve on certain 2013 model year Audi 4.0L vehicles may not be present or may have been incorrectly installed during production. |
| A011507 2028344- | 2017-10-25. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 01 number 13-69 dated February 14, 2013. Noises and inconsistent engine operation after cold start during the catalyst heating phase. The customer may misinterpret these symptoms as engine misfiring. This bulletin applies only to non-diesel engines. |
| A271525 2036392- | 2017-10-25. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE. Supersedes Technical Service Bulletin Group 27 number 14-23 dated April 24, 2014. Vibrations are felt at 1000 rpm and 3000 rpm. DTCs may be stored in the subframe mount control module. Optimized J931 control module software. |
| A151526 2039995- | 2017-10-25. Service bulletin. ENGINE; POWER TRAIN. Rattling noises are heard from the timing chain drive for about 1-3 seconds after the first engine start of the day. The noises are caused by one of the upper chain tensioners. The noises do not lead to damage. Improved chain tensioner. |
| A171562 2040644- | 2017-10-21. Service bulletin. ENGINE AND ENGINE COOLING. A metallic whistling or grinding sound is heard from the engine compartment when the vehicle is at idle speed. The sound usually only occurs when the engine is warm. The MIL is sporadically on. DTC P2279 and DTC P0507 are stored in the ECM. A leak in the crankcase breather module (pressure regulating valve) can cause this condition. |
| A011522 2038045- | 2017-10-21. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM. Supersedes Technical Service Bulletin Group 01 number 14-88 dated August 15, 2014. The MIL is on. DTC P218100 (Cooling System Performance) is stored in the engine control module (ECM), J623 (address word 01). DTC P218100 will be stored if, after a specified air flow (warm-up phase), the measured engine temperature does not reach the value in the timing map. Particles in the cooling system from the production process affect the closing of the coolant thermostat. Replacing the coolant temperature sender does not fix the problem. |
| A171557 2010043- | 2017-10-21. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 17 number 13-35 dated January 9, 2013. This bulletin lists engine oils that meet Audi oil quality standards (VW 501 01, 502 00, 505 00, 505 01, and 504 00/507 00). |
| A101511 2018288- | 2017-10-21. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 10 number 13-10 dated September 5, 2013. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these metal debris pieces are not removed prior to the installation and operation of the replacement engine, they could be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.