Service bulletins for the 2010 Audi Q7
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
864 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Electrical system are shown. Show all
| A571385 2017082- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM; LATCHES/LOCKS/LINKAGES:DOORS:LATCH. Supersedes Technical Service Bulletin Group 57 number 13-82 dated February 5, 2013. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced. If other senders operate in the same frequency range (mobile phones, TV stations, wireless headphones, baby monitors, other vehicle remote controls, etc.), the remote control key may have been temporarily switched off because a clear identification of the remote control key is not possible. This is necessary to prevent an unintentional unlocking of the vehicle by other unrelated senders. |
|---|---|
| A941310 2029194- | 2017-11-17. Service bulletin. EXTERIOR LIGHTING; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 94 number 13-03 dated February 1, 2013. Only vehicles with Xenon headlights can be affected by this condition. The customer complains the high beams do not function on one side or one of the low beams flickers intermittently. In addition to this, an "Adaptive Headlight Defective" warning can be present in the cluster if the vehicle has the Prestige trim level. One of the following DTCs are set in the vehicle electrical system control module, J519 (09), or in the headlamp range control module, J431 (55), depending on the trim level of the vehicle. Vehicles with the Premium Plus option package can have the DTC set in the J519 (09) module. Vehicles with the Prestige option package can have the DTC set in the J431 (55) module. One or more of the connectors inside the headlamp housing are disconnected fully or partially from the factory. |
| A961501 2019260- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 96 number 13-67 dated July 10, 2013. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer?s door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. In A4 model years 2005?2006 and A3 model year 2009, the actual location of the garage door opener control module differs from the location shown in the owner's manual (opposite side of front bumper). The customer may misunderstand the programming procedure, particularly if the customer?s HomeLink® opener system is using an alternate code. The handheld transmitter?s programming function may become inoperative, or the transmitter is too far away from J530. Interference prevents the communication between handheld transmitter and J530. Interference prevents the communication between handheld transmitter and J530. If the vehicle flashes during the programming of a handheld transmitter, this does not necessarily indicate that the programming was successful; it only indicates that the vehicle has recognized and saved a signal. |
| A481567 2017266- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 48 number 14-62 dated September 23, 2014. Electrically-adjustable steering column adjustment is restricted and does not adjust vertically. Incorrect operation of Easy Entry is not the cause. It is unlikely that external forces have led to the loss of the stored end positions of the adjustment movement. See TSB 2015819, 48 Easy Entry function of the power adjustable steering column intermittently does not work, for more information. Seat adjustments can be used to maintain the 10-inch minimum recommended distance from the steering wheel in case of airbag deployment. The axial adjustment is still functional during this condition. The steering column may be under tension due to unfavorable tolerances of the steering column and module cross carrier. As a result, the current draw of the regulator motors is above specification, which causes the electric steering column adjustment to fail. Once the vehicle electrical system control module, J519 (address word 09), detects an excessive current draw, the basic settings will be erased. If basic settings are not stored in the vehicle electrical system control module, the module will not send voltage/current to the motor to operate the vertical adjustment. |
| A911529 2013422- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 91 number 13-04 dated September 11, 2013. The Bluetooth® telephone cannot be connected to the vehicle?s Infotainment system. Certain restrictions are present when a Bluetooth device is connected to the vehicle. The restrictions vary depending on the vehicle system present. |
| A171568 2028440- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY. Supersedes Technical Service Bulletin Group 17 number 14-49 dated April 3, 2014. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. The displayed vehicle range drops inconsistently. After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer. |
| A231537 2040752- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE. Supersedes Technical Service Bulletin Group 23 number 15-36 dated July 17, 2015. The MIL is on. Vehicle either runs roughly or does not start. DTCs are stored in the ECM. Metallic particles in the high pressure fuel pump may cause the condition. |
| A011309 2014753- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE. Supersedes Technical Service Bulletin Group 00 number 10-01 dated February 5, 2010. Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. Engine runs rough after cold start. Excessive engine cranking time. Hesitations while driving. Rough engine idle. Reduced engine performance. Poor fuel economy. Conditions may be severe enough to illuminate the MIL in conjunction with storage of DTCs for misfire (example: P0300, P030x) and / or lean fuel system (example: P0171, P0174, P1128, P1130, P1136, P1138) in the engine control module (ECM). Condition may be caused by use of contaminated gasoline. Condition may be caused by use of gasoline with a low content of deposit control additives. |
| A961364 2029384- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 96 number 12-32 dated April 27, 2012. The customer is able to program one or more of the Homelink buttons using their garage door remote, but after a few days or weeks, one or more of the programmed Homelink buttons no longer function. The LED on the Homelink button that is no longer functioning now flashes slowly, indicating that no programming is stored. The customer?s transmitter operates at 295Mhz. At the workshop, the Homelink system can be programmed to the workshop garage door successfully. No trouble is found. No DTCs are stored in any control units. The garage door opener control module, J530, was designed with an operational frequency range in which the 295Mhz frequency works correctly during the initial programming of the system. Over time, the transmitting frequency can drift out of range (especially in warmer climates), causing the system to lose its programming. |
| A941296 2027773- | 2017-11-08. Service bulletin. EXTERIOR LIGHTING:HEADLIGHTS; EQUIPMENT; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 94 number 12-69 dated March 15, 2012. Part or all of the daytime running lights do not work on vehicles with LED DRLs. For vehicles with halogen DRLs, please reference TSB 2017488, 94 Halogen Daytime running lights do not work. In the past, the daytime running light bulbs were a serviceable part. In this application, the LED strip cannot be replaced, and may have an associated control module. This TSB is for servicing information only. |
| A941298 2028277- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING:HEADLIGHTS; EQUIPMENT. Supersedes Technical Service Bulletin Group 94 number 12-91 dated October 24, 2012. Considerable moisture present in headlamp. The moisture disappears only after extended drives (greater than 10 minutes). No external damage to headlamp which could introduce moisture. Humid air settles on the inside of the glass, causing moisture to appear on the inside of the headlamp lens. Because of the headlamp circulation system, outside air is allowed to flow through the headlamps. The open, water-protected ventilation system (needed for pressure compensation) creates different ? climate zones? inside the headlamp, where the lens is either warmed up by the light or cooled down by passing air. When high air humidity and temperature differences exist between the inside of the headlamps and the outside, condensation can form on the inside of the lens, especially in cold and wet weather. The moisture in the headlamps can be compared with condensation on the windshield, which is cleared by the "defroster vent". This moisture buildup can happen for example: after a car wash, after steam cleaning of the engine or the front end, or after overnight temperature changes. This condition is more easily visible with headlamps made from clear glass. The moisture is an optical condition which does not affect the headlamp function (light performance) and does not lead to corrosion nor does it lead to damage of the internal headlamp parts. This condition is common to all exterior vehicle lights, and can occur on every headlamp, fog lamp, or rear lamp. |
| A941299 2029194- | 2017-11-08. Service bulletin. EXTERIOR LIGHTING; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 94 number 12-74 dated April 23, 2012 . The customer complains the high beams do not function on one side or one of the low beams flickers intermittently. In addition to this, an ? Adaptive Headlight Defective? warning can be present in the cluster if the vehicle has the Prestige trim level. DTCs are set in the 09 ? Central Electric Control Unit or in the 55 ? Headlamp Range Control Unit depending on the trim level of the vehicle. Vehicles with the Premium Plus option package can have the DTC set in the 09 module. Vehicles with the Prestige option package can have the DTC set in the 55 module. One or more of the connectors inside the headlamp housing are disconnected fully or partially from the factory. |
| Update Bulletin | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; STRUCTURE; EQUIPMENT. Supersedes Technical Service Bulletin Group 23 number 10-05 dated February 26, 2010. The ?TDI? and rear ?quattro? emblems are missing from the lower right corner of the rear lid. MIL on. DTC P229F or P2201 (NOx Sensor Circuit Range/Performance) stored in ECM. Procedure is valid only for vehicles that show the 23F1 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicle must be within the Limited New Vehicle Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. The work instructions for installing the ?TDI? and rear ?quattro? emblems during assembly were removed for a short production run. Software update needed. |
| A271214 2031145- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM. complaints are reported by the customer regarding electrical features and functions in the vehicle. One or more warning lights on in cluster. The DIS or other displays in cluster are blank. MMI does not function. Windows do not function. LED indicators in various buttons inside the vehicle do not light up. The voltage regulator on the alternator can sporadically fail causing the electrical system to experience too high of voltage. As a result, the affected vehicle electronic components go in to high voltage protection and deactivate sensitive displays and indicators to prevent electrical damage. When an over voltage condition occurs the vehicle electronics and alternator are protected, thus there is no need to replace the entire alternator assembly. |
| A271215 2031145- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 27 number 12-14 dated October 12, 2012. Complaints are reported by the customer regarding electrical features and functions in the vehicle. One or more warning lights on in cluster. The DIS or other displays in cluster are blank. MMI does not function. Windows do not function. LED indicators in various buttons inside the vehicle do not light up. The voltage regulator on the alternator can sporadically fail causing the electrical system to experience too high of voltage. As a result, the affected vehicle electronic components go in to high voltage protection and deactivate sensitive displays and indicators to prevent electrical damage. When an over voltage condition occurs the vehicle electronics and alternator are protected, thus there is no need to replace the entire alternator assembly. |
| A431211 2018765- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 43 number 12-08 dated February 2, 2012. The self-leveling system cannot be adjusted any more with the MMI. The compressor for the self-leveling system continues to run after switching off the engine and locking the vehicle. DTCs may be stored. Because of poor performance or failure of the compressor for air suspension, the vehicle position cannot be adjusted. As a safeguard, the control module will lower the vehicle to the lowest position and illuminate the warning light. Drivability is not affected. |
| A571278 2031413- | 2017-11-08. Service bulletin. SEATS; ELECTRICAL SYSTEM. The seat memory does not work. The MMI displays that the memory function is not active. The seat memory control unit can be deactivated due to voltage fluctuations in the vehicle? s power system, or from a large static discharge through the seat cover. If the seat memory control unit is deactivated due to the above mentioned influences, the control unit cannot be reactivated through any vehicle controls, vehicle keys, or through the normal GFF test plans. It can only be reactivated with special test plans within the tester. |
| A571279 2018737- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Supersedes Technical Service Bulletin Group 57 number 10-32 dated September 9, 2010. Customer may complain that the vehicle locks itself when removing the key from the ignition lock. When removing the ignition key from the ignition, the customer may unintentionally operate the lock button of the remote key. With the S contact in the ignition lock off (key is removed), the central locking will resume to respond to signals from the remote key. MVB 17 in electric control unit address $46 (Comfort System Central Control Module) can be used for argumentation. The last received central locking command is stored in this MVB. A value of ?2? indicates a locking command last sent from the remote key. With the Autolock feature, MVB 17 is overwritten. Therefore MVB 17 must be read immediately after the complaint. |
| A911263 2021151- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER. Supersedes Technical Service Bulletin Group 91 number 11 ? 83 dated April 15, 2011. The customer may report that the illumination of the dash insert, the air conditioning control panel or the inside light flickers when briefly pressing the accelerator in P or N or when shifting down while driving downhill. Only vehicles with PR number 8GH may be affected. When high electricity consumers are switched off and the battery is fully charged, the energy generated by the alternator is sometimes too great for the power system to absorb. This may lead to briefly increased voltage, and the lights mentioned above may briefly flicker. This characteristic is caused by the alternator design and is a normal condition of the vehicle. |
| A911264 2031367- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EQUIPMENT. CD or DVD disks do not automatically change from one to the next in the external CD or DVD changer. The CD and DVD changer have different operating concepts. MMI3G: Disks in the CD changer are always automatically changed from one to the next. MMI3G+ (with Audi connect): Disks in the CD changer are automatically changed from one to the next, but this operation is disabled when the Repeat option is turned on in the Media Settings menu. By default (MMI factory default setting) the repeat option is set to ? Off?. DVD changer (A8 only): Disks in the DVD changer can only be changed manually. |
| A901238 2032113- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. The customer may state that the outside ambient temperature display is incorrect. To achieve a smoothening effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor measurement. The display will not change faster than 4° F (2° C) per minute. This concept applies to both falling and rising temperatures. A programming strategy is also implemented to avoid incorrect readings on a parked vehicle, due to the temperature sensor being affected by outside influences such as radiant heat from the engine bay, elevated road surface temperatures, etc. |
| A941200 2024877- | 2017-11-08. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; EXTERIOR LIGHTING:HEADLIGHTS. Supersedes Technical Service Bulletin Group 94 number 12-83 dated July 9, 2012. Warning light for dynamic headlight range control is displayed in the instrument cluster. DTC 00003 / 14 (Control unit faulty) is registered in the dynamic headlight range control unit, address word 55. Both headlights function normally. Vehicles equipped with adaptive (cornering) lighting. New software version 0010 in the dynamic headlight range control module addresses this condition. If the headlight range control module has a software version lower than 0010 installed, then use the SVM code listed in Service to update the module. Some control units will already have software version 0010 installed but can still exhibit the conditions mentioned above. When this occurs, the software will need to be reflashed using a separate SVM code. The corrupt software will be overwritten. The software version does not change after the update. |
| A571402 2022032- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 57 number 13-97 dated October 29, 2013. The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle ?locked itself?. The lock command history is stored in the convenience system control module (J393). |
| A001466 2037949- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. A DTC with the description ?Invalid Data Record? is stored after an ECU has been replaced or updated. This DTC is normal. It indicates that the parameter data has not been properly programmed into the ECU by SVM. |
| A001465 2011732- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 00 number 12-32 dated February 7, 2012. This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.