Service bulletins for the 2008 Audi Q7
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
458 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Equipment and accessories are shown. Show all
| A9615002027416-6 | 2018-02-05. Service bulletin. EQUIPMENT. Supersedes Technical Service Bulletin Group 96 number 14-85 dated July 24, 2014. The sunglass holder in the dome light assembly will not latch closed or is stuck closed. The condition may be intermittent. The sunglass holder spring latch mechanism may have been damaged during the assembly procedure. |
|---|---|
| ATE-17-05 | 2018-02-05. Service bulletin. EQUIPMENT. Due to increasing requests for high voltage personal protective equipment (HVE PPE) for dealer technicians working with high voltage vehicles (Hybrid, Plugin Hybrid, Electric Vehicle), the Volkswagen Tools and Equipment Team has identified two US based suppliers to support dealers in USA and Canada. |
| A571738 2017082- | 2018-02-05. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This informational bulletin contains instructions for sychronizing the remote key after the battery has been disconnected or replaced. |
| A001684 2037949- | 2018-02-05. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This technical bulletin provides instructions for an an error message and updating with an SVM code. |
| A871447 2010146- | 2017-12-14. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Supersedes Technical Service Bulletin Group 87 number 12-27 dated April 24, 2012. There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor. If the odor is noticeable in the vehicle when the engine is not turned on, the cause may be mold and mildew in the passenger compartment, and not be related to the A/C system. All other possible sources of the odor must be investigated before this bulletin can be performed. |
| Accessories Oper | 2017-12-05. Service bulletin. EQUIPMENT. This is an advance notice for Audi of America employees. This notice contains information for the accessories operations technical bulletin. |
| A911472 2024323- | 2017-12-05. Service bulletin. EQUIPMENT. Supersedes Technical Service Bulletin Group 91 number 13-74 dated February 5, 2013. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions. |
| A901451 2021151- | 2017-12-05. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Supersedes Technical Service Bulletin Group 91 number 12-63 dated October 4, 2012. The customer may report flickering of the dash insert lighting, of the A/C control panel lighting, or of the inside light. The condition occurs when the accelerator is pressed while the vehicle is in P or N, or when the vehicle is shifted down when moving downhill. Only vehicles with PR number 8GH may be affected. When high electricity consumers are switched off when the battery is fully charged, the energy generated by the alternator is sometimes too great for the power system to absorb. This may lead to briefly-increased voltage, causing the lights to flicker. |
| A441456 2022563- | 2017-12-05. Service bulletin. EQUIPMENT. Supersedes Technical Service Bulletin Group 44 number 14-50 dated May 14, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. Customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. |
| 2013 06 Audi Bra | 2017-12-05. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; SERVICE BRAKES. This document contains information on the Audi braking guard. |
| A911302 2018187- | 2017-12-05. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. Supersedes Technical Service Bulletin Group 91 number 11-20 dated October 21, 2011. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices. |
| A961367 2019260- | 2017-12-05. Service bulletin. EQUIPMENT:ELECTRICAL. Supersedes Technical Service Bulletin Group 96 number 12-37 dated June 11, 2012. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer's door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. In A4 Model Years 2005 - 2006 and A3 Model Year 2009, the actual location of the garage door opener control module differs from the location shown in the owner's manual (opposite side of front bumper). The customer may misunderstand the programming procedure, particularly if the customer's HomeLink® opener system is using an alternate code. The handheld transmitter's programming function may become inoperative, or the transmitter is too far away from J530. Interference prevents the communication between handheld transmitter and J530. If the vehicle flashes during the programming of a handheld transmitter, this does not necessarily indicate that the programming was successful; it only indicates that the vehicle has recognized and saved a signal. |
| A911392 2030947- | 2017-12-05. Service bulletin. EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 91 number 12-61 dated September 25, 2012. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth®-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype®, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone gets the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call assuming the phone is not responding. |
| A571382 2017082- | 2017-11-17. Service bulletin. LATCHES/LOCKS/LINKAGES; EQUIPMENT:ELECTRICAL. Supersedes Technical Service Bulletin Group 57 number 11-55 dated August 22, 2011. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced. If other senders operate in the same frequency range (mobile phones, TV stations, wireless headphones, baby monitors, other vehicle remote controls, etc.), the remote control key may have been temporarily switched off because a clear identification of the remote control key is not possible. This is necessary to prevent an unintentional unlocking of the vehicle by other unrelated senders. |
| A001348 2002047- | 2017-11-17. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Supersedes Technical Service Bulletin Group 00 number 11-19 dated April 8, 2011. This TSB contains information on technician preparation when calling the Audi Technical Assistance Center |
| A911518 2016513- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. Supersedes Technical Service Bulletin Group 91 number 10-59 dated September 15, 2010. In Mix (shuffle) mode, very long response times and subsequent malfunctions occur when the next track is being selected. Long response times also occur when the ?Return? hard key is pressed. In Mix (shuffle) mode, the previous track is not played when the ?Previous? button is selected in the CD control menu. A different track plays instead. In Mix (shuffle) mode, when the first track of the playlist was selected via the ?Previous? button in the CD control menu (rather than with the rotary push button), the track list shown in the MMI does not match the track list shown in the driver information panel (synchronization issue). In Mix (shuffle) mode, the current track is not highlighted in white letters in the MMI display. If the current track is selected again via the rotary push button, the audio briefly drops out. The current track is not color-highlighted in the MMI display. Audiobook tracks continuously fast-forward if ?Fast Forward? was selected in the first few seconds after the track started playing. The message ?Device is being initialized. Please wait?? is displayed when a second generation iPod Nano is installed. iPod locks up but is operable again after the iPod is reset. iPod performs a reset and restarts on its own. iPod is not detected when it is plugged into the AMI. The message ?Device or cable type not supported? appears in the MMI display. An automatic iPod upgrade through iTunes contained inoperative driver software. The customer may not realize that the iPod was updated and may complain that the AMI software is causing the issues. Because downgrading the updated iPod software is usually not possible, the AMI driver software (firmware) must be updated. The firmware update of AMI is not a ZUG update. Unlike ZUG updates, which are performed with an update CD in the CD changer, this firmware update is performed with a USB device connected dir |
| A911526 2042097- | 2017-11-17. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). The traffic feature in the MMI navigation is inoperative. If the vehicle is a model year 2016 A6 or A7, see TSB 2042013: 91 Audi connect online destination search, Google Earth navigation view, or INRIX online traffic is not available. There is a known server issue that can only be resolved through a change to the Audi AG backend server. Audi has changed traffic providers over the years as new technologies have developed. This bulletin provides an overview of the different systems and the basic checks that can be performed to diagnose complaints related to traffic in the MMI navigation system. |
| A001578 2021205- | 2017-11-17. Service bulletin. EQUIPMENT:OTHER:LABELS. Supersedes Technical Service Bulletin Group 00 number 10-05 dated June 14, 2010. VIN plate and/or B-Pillar Safety Certification label requires replacement. |
| A571279 2018737- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Supersedes Technical Service Bulletin Group 57 number 10-32 dated September 9, 2010. Customer may complain that the vehicle locks itself when removing the key from the ignition lock. When removing the ignition key from the ignition, the customer may unintentionally operate the lock button of the remote key. With the S contact in the ignition lock off (key is removed), the central locking will resume to respond to signals from the remote key. MVB 17 in electric control unit address $46 (Comfort System Central Control Module) can be used for argumentation. The last received central locking command is stored in this MVB. A value of ?2? indicates a locking command last sent from the remote key. With the Autolock feature, MVB 17 is overwritten. Therefore MVB 17 must be read immediately after the complaint. |
| A911263 2021151- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER. Supersedes Technical Service Bulletin Group 91 number 11 ? 83 dated April 15, 2011. The customer may report that the illumination of the dash insert, the air conditioning control panel or the inside light flickers when briefly pressing the accelerator in P or N or when shifting down while driving downhill. Only vehicles with PR number 8GH may be affected. When high electricity consumers are switched off and the battery is fully charged, the energy generated by the alternator is sometimes too great for the power system to absorb. This may lead to briefly increased voltage, and the lights mentioned above may briefly flicker. This characteristic is caused by the alternator design and is a normal condition of the vehicle. |
| A901238 2032113- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. The customer may state that the outside ambient temperature display is incorrect. To achieve a smoothening effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor measurement. The display will not change faster than 4° F (2° C) per minute. This concept applies to both falling and rising temperatures. A programming strategy is also implemented to avoid incorrect readings on a parked vehicle, due to the temperature sensor being affected by outside influences such as radiant heat from the engine bay, elevated road surface temperatures, etc. |
| A941200 2024877- | 2017-11-08. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; EXTERIOR LIGHTING:HEADLIGHTS. Supersedes Technical Service Bulletin Group 94 number 12-83 dated July 9, 2012. Warning light for dynamic headlight range control is displayed in the instrument cluster. DTC 00003 / 14 (Control unit faulty) is registered in the dynamic headlight range control unit, address word 55. Both headlights function normally. Vehicles equipped with adaptive (cornering) lighting. New software version 0010 in the dynamic headlight range control module addresses this condition. If the headlight range control module has a software version lower than 0010 installed, then use the SVM code listed in Service to update the module. Some control units will already have software version 0010 installed but can still exhibit the conditions mentioned above. When this occurs, the software will need to be reflashed using a separate SVM code. The corrupt software will be overwritten. The software version does not change after the update. |
| A961485 2027416- | 2017-11-08. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. Supersedes Technical Service Bulletin Group 96 number 13-61 dated May 28, 2013. The sunglass holder in the dome light assembly will not latch closed. The sunglass holder spring latch mechanism may have been damaged during the assembly procedure. |
| A911450 2018187- | 2017-11-08. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. Supersedes Technical Service Bulletin Group 91 number 13-02 dated August 30, 2013. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices. |
| A001467 2002047- | 2017-11-08. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Supersedes Technical Service Bulletin Group 00 number 14-61 dated May 1, 2014. Technician preparation when calling the Audi Technical Assistance Center (TAC). |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.