Service bulletins for the 2012 Audi Q5
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1284 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| A801305 2033806- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM:WIRING. Supersedes Technical Service Bulletin Group 80 number 13-04 dated August 9, 2013. Malfunction Indicator Lamp is on. Climate system heating performance is insufficient. Coolant level warning is on. Engine temperature is elevated. ?Limp Home? mode is active. Faults are stored in the transmission control module. Coolant loss is found from one or more control valves: N82, N509, or N488. Coolant may have migrated into the wiring harness through the connector and into various control units. Climate system heating performance is insufficient due to coolant loss, or due to a faulty N82 control valve. Inspection of the coolant control valves N82, N509, or N488 reveals the presence of coolant inside the electrical connector as shown in the illustration. The connectors, wiring harness, and/or connected control units may have been damaged from exposure to coolant. |
|---|---|
| A741311 2028257- | 2017-10-31. Service bulletin. SEATS. Supersedes Technical Service Bulletin Group 74 number 12-08 dated April 24, 2012. The customer may complain that the seat heating temperature is too low or that it takes too long to heat up. From model year 2012, an additional row of fastening features were added to improve the fit of the leather seat covers on the basic and sports seats. As a consequence of this change, the temperature sensor within the seat was moved to a location that is more sensitive to heat. As a result, the control limit is reached too early and the heat is reduced before the seating surface reaches the correct temperature. |
| A721309 2035357- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Seat memory function does not work. DTCs are stored. In the event of a voltage fluctuation in the vehicle power system, the software of the seat adjustment module fails. |
| A721305 2030729- | 2017-10-31. Service bulletin. SEATS. Supersedes Technical Service Bulletin Group 72 number 12-04 dated November 30, 2012. Customer may report hearing squeak or rattle sounds coming from the rear seat area. The rattle sound may be caused from the pivot point of the torsion bar within the 2/3 rear seat backrest pivot assembly. The squeak noise may be coming from the rear seat armrest area, specifically from the contact surface between the armrest lock and the striker pin. |
| A661334 2029586- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 66 number 13-32 dated September 26, 2013. The customer may report hearing wind noise while driving at highway speeds. The noise may occur on either side of the vehicle. Wind noise may be coming from either the mirror base or the lane change assist lamp. Improved parts are available. |
| A661333 2033517- | 2017-10-31. Service bulletin. VISIBILITY. Supersedes Technical Service Bulletin Group 66 number 13-27 dated April 8, 2013. Wind noise is heard by the customer at highway speeds. Air flows through the exterior rear view mirror housing at the seam where the turn signal lamp meets the housing. This causes a high-frequency whistling tone. |
| A661332 2029586- | 2017-10-31. Service bulletin. VISIBILITY. Supersedes Technical Service Bulletin Group 66 number 13-31 dated June 12, 2013. The customer may report hearing wind noise while driving at highway speeds. The noise may occur on either side of the vehicle. Wind noise may be coming from either the mirror base or the lane change assist lamp. Improved parts are available. |
| A571394 2035367- | 2017-10-31. Service bulletin. EQUIPMENT. Various features in the rear passenger compartment are inoperative. Some features may include power rear windows, rear climate control operating unit, rear sunroof panel, rear reading lamps, rear cigarette lighters, etc. By design, many electronically-controlled features in the rear passenger compartment, in addition to the power rear windows, are deactivated if the child lock in the driver's door is activated. |
| A511307 2009967- | 2017-10-31. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. Supersedes Technical Service Bulletin Group 51 number 13-06 dated August 9, 2013. Instructions for vehicle inspection, protection removal, and detailing. |
| A481354 2028220- | 2017-10-31. Service bulletin. WHEELS; STEERING. Supersedes Technical Service Bulletin Group 48 number 12-30 dated June 25, 2012. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g., contact with finger nails, zippers, watches, rings etc.) can cause damage to the appearance of the steering wheel. This type of damage is not warrantable, as numerous investigations have shown that there is no fault in material or workmanship. |
| A451307 2033412- | 2017-10-31. Service bulletin. STEERING. Supersedes Technical Service Bulletin Group 97 number 13-35 dated March 27, 2013. Steering wheel does not lock. Various warning lights are on. Steering feels stiffer than usual. The engine cannot be switched off. The ignition key cannot be removed. There are DTC entries present in the system (either static or sporadic). DTCs are stored in the ABS control module. This condition does not result in any drivability concerns. The steering system is fully connected. The insulation for the ABS wheel speed sensor is damaged in production. Over time, this can lead to corrosion on the wires and restricted functions with the ABS control module. Only the wires in the left bulkhead grommet are affected. |
| A441342 2022563- | 2017-10-31. Service bulletin. SUSPENSION; STEERING. Supersedes Technical Service Bulletin Group 44 number 13-36 dated February 18, 2013. This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration in one or both of the following circumstances: * When driving at highway speeds from 55 - 80 mph (88 - 128 km/h). * When applying low brake pedal pressure with minor slow down. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires. |
| A401336 2035358- | 2017-10-31. Service bulletin. STEERING. The customer complains that rattling or engine noise can be heard in the passenger compartment. The plastic sleeve of the intermediate steering shaft can slip towards the universal joint (mounting of the power steering rack), causing rattling or engine noise that can be heard in the passenger compartment. Improved production process. |
| A401335 2023187- | 2017-10-31. Service bulletin. STEERING; WHEELS. Supersedes Technical Service Bulletin Group 40 number 12-23 dated May 14, 2012. Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. The folds of the outer rubber boots on the front axle shafts may come in contact with each other when the steering wheel is turned, causing squeaking noises. These noises are more likely to occur when the vehicle is new. The volume and occurrence of the noise will dissipate after a short break-in period. |
| A371317 2029027- | 2017-10-31. Service bulletin. POWER TRAIN. Supersedes Technical Service Bulletin Group 37 number 13-02 dated April 26, 2013. Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. After key cycle, the vehicle drives without restriction. DTCs is stored in the transmission control module (TCM). If DFCCs do not match exactly, this TSB does not apply. |
| A171341 2027501- | 2017-10-31. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 17 number 11-24 dated November 11, 2011. Electronic oil consumption measurement - Repair Authorization Model Year 2012. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine, and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, and the ambient temperature and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Utilizing the advanced sensor technology integrated in the 2009> B8 platform (A4, allroad, A5, A5 Cabriolet, A6, and Q5) equipped with the 2.0 TFSI (CAEB, CPMA) engine, it is possible to measure oil consumption electronically via a Guided Function test plan. The electronic oil consumption measurement will only function on the 2.0 TFSI engine with engine code CAEB and CPMA. |
| A101310 2018288- | 2017-10-31. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 10 number 10-02 dated September 14, 2010. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the vehicle's engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these pieces are not removed prior to the installation and operation of the replacement engine, the pieces may be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage. |
| A011330 2027082- | 2017-10-31. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 24 number 12-28 dated April 24, 2012. MIL on. DTC P0234 (Turbo/Super Charger Overboost Condition) is stored in the engine control module, J623 (address word 01). No other DTCs are stored. DTC P0234 can be set inadvertently by the software application. DTC P0234 can be set with an actual cause in combination with loss of engine power and low/uneven engine performance, based on charge pressure control. |
| A011329 2033223- | 2017-10-31. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 01 number 13-73 dated March 7, 2013. The engine warning light is on after engine replacement. The engine is not running roughly. However, the engine control module, J623 (01), is storing one or more of the following engine misfire fault codes: DTCs P0300 - P0304. The fault codes occur at light load, between 8% and 14% accelerator pedal position. The programmed values for the misfiring recognition are not automatically reset by deleting the memory once. |
| A691326 2023323- | 2017-10-31. Service bulletin. AIR BAGS; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 69 number 12-25 dated April 25, 2012. After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. An SVM code is required to code and parameterize the new service replacement airbag control module. Each model?s SVM code is provided in a parts bulletin (GP bulletin), which should have been referenced through ETKA when the module was replaced. The control module cannot be coded until the SVM code has been executed. |
| A661336 2029586- | 2017-10-31. Service bulletin. VISIBILITY. Supersedes Technical Service Bulletin Group 66 number 13-34 dated September 30, 2013. The customer may report hearing wind noise while driving at highway speeds. The noise may occur on either side of the vehicle. Wind noise may be coming from either the mirror base or the lane change assist lamp. Improved parts are available. |
| A571397 2022032- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 57 number 13-92 dated August 1, 2013. The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle ?locked itself?. The lock command history is stored in the convenience system control module (J393). |
| A271319 2029010- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. Supersedes Technical Service Bulletin Group 27 number 12-13 dated March 22, 2012. The customer may report a discharged battery when trying to start the vehicle. The condition results in a no start. |
| A271318 2023282- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. Supersedes Technical Service Bulletin Group 27 number 12-10 dated February 13, 2012. Battery testing and charging for vehicles equipped with a Battery Data Manager (BDM - J367). When the InCharge 940 is used as a battery charger in auto mode, it performs a battery condition test and may prematurely fail the battery if the charging takes place at the jumper posts in the engine compartment. This is due to the added resistance in the system between the battery and jumper posts. When the InCharge 940 is used as a battery charger in manual mode, the battery condition test is not performed. |
| A011337 2033001- | 2017-10-31. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 01 number 13-24 dated August 20, 2013. MIL on. DTCs are stored in the engine control module. Mileage is greater than 15,000 miles. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.