Service bulletins for the 2014 Audi A8
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1325 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Engine are shown. Show all
| A191562 2025303- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 19 number 15-61 dated July 7, 2015. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service. |
|---|---|
| A171565 2038129- | 2017-11-17. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 17 number 15-63 dated June 2, 2015. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual. |
| Dealer Letter - | 2017-11-17. Service bulletin. ENGINE. This is an update to the November 3, 2015 communication where Volkswagen Group of America, Inc. issued a stop sale order for all 2013-2016 model year Audi vehicles equipped with a Gen II 3.0 liter V6 TDI engine. This was in response the notice received from the U.S. Environmental Protection Agency and California Air Resources Board of an investigation related to certain emissions compliance matters impacting certain 3.0 liter V6 TDI engine vehicles. Audi continues to actively cooperate with the relevant authorities to resolve the November 2, 2015 EPA notice of violation. |
| A191341 2025303- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 19 number 13-35 dated March 25, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service. |
| A011257 2028344- | 2017-11-08. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR; ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 01 number 12-51 dated July 18, 2012. Noises/inconsistent engine operation after cold start during the catalyst heating phase. The customer may interpret this engine roughness as misfiring. To comply with the legal requirements on exhaust gas emissions according to the LEV-1 and LEV-2 standards, a high exhaust gas quality must be ensured. The necessary catalyst only operates at a temperature over 300°C (572°F). To achieve this, the catalyst is heated up. The catalyst heating phase is achieved by a late ignition angles and by introducing additional fresh air to the exhaust valves (secondary air system). Late ignition angles make sure that the exhaust gas from the cylinders has a higher temperature. This exhaust gas includes fuel that is un-burnt, and was deliberately injected into great quantities. The secondary air system adds fresh air to the exhaust gas as it leaves the cylinder and the extra fuel is burnt. As a result, the temperature of the exhaust gas and of the catalyst increases quickly. The afterburning in the exhaust manifold before catalyst changes the sound characteristic of the engine. This heating-up of the catalyst, including afterburning, is normal and has no effect on the service life of the engine. During this catalyst heating phase the engine has increased idle speed, may have increased vibrations, and a different sound characteristic. Depending on conditions the time of the catalyst heating phase varies. |
| A001463 2033576- | 2017-11-08. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Supersedes Technical Service Bulletin Group 00 number 13-49 dated May 14, 2013. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage. |
| A201434 2035073- | 2017-11-08. Service bulletin. EQUIPMENT:ELECTRICAL; ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 20 number 14-32 dated March 21, 2014. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak. |
| A191450 2025303- | 2017-11-08. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 19 number 13-41 dated June 20, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service. |
| A011481 2035368- | 2017-11-08. Service bulletin. ENGINE; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 01 number 13-32 dated September 26, 2013. The MIL is on. DTC P203B00 (Reductant Level Sensor Circuit Range/Performance) is stored in the engine control module (ECM), J623 (address word 01).Due to a production issue for the level sensor, the ECM cannot correctly read the reductant (AdBlue) fluid level. |
| A001464 2035581- | 2017-11-08. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 00 number 13-55 dated October 21, 2013. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to a W12 engine, the increased oil flow rate forces oil into the intake manifold or combustion chamber and damages the engine. |
| A271423 2036392- | 2017-11-08. Service bulletin. ENGINE; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 27 number 14-22 dated April 21, 2014. Vibrations are felt at 1000 rpm and 3000 rpm. DTCs may be stored in the subframe mount control module. The basic settings of the active engine mounts in the subframe mount control module, J931, are deactivated when work is done on either of the vehicle electrical system control modules. As a result, the vehicle vibrates or judders when cylinders are actively switched off. |
| A971441 2036764- | 2017-11-08. Service bulletin. ENGINE; ELECTRICAL SYSTEM. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly. |
| A201432 2035073- | 2017-11-08. Service bulletin. ENGINE AND ENGINE COOLING. upersedes Technical Service Bulletin Group 20 number 14-31 dated January 9, 2014. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak. |
| A011462 2036169- | 2017-11-08. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 01 number 14-59 dated January 21, 2014. The MIL is on. DTC may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise. |
| A011461 2035235- | 2017-11-08. Service bulletin. ENGINE; POWER TRAIN. Supersedes Technical Service Bulletin Group 01 number 13-36 dated October 9, 2013. The customer reports that the engine warning light illuminates sporadically. The engine may have reduced performance without significant loss of power or stalling. Noise is heard coming from the engine compartment, specifically from the High Pressure Fuel Pumps 2. DTCs are stored in the ECM. |
| A011459 2036169- | 2017-11-08. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 01 number 14-55 dated January 8, 2014. The MIL is on. DTC P0087 may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise. |
| A011455 2036169- | 2017-11-08. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP. The MIL is on. DTC P0087 may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20° F (-7° C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?. |
| A001458 2026692- | 2017-11-08. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; ENGINE. Supersedes Technical Service Bulletin Group 00 number 12-43 dated December 21, 2012. If a 2012 - 2015 Audi A8 L W12 arrives at an Audi dealership and requires diagnosis or repair, a Repair Authorization must be obtained. Prior to any repair, a Technical Assistance Center (TAC) ticket must be created for engine and transmission concerns only. Routine maintenance and PDI do not require prior authorization or a Technical Assistance Center (TAC) ticket. These procedures are mandatory until further notice. Warranty repairs without repair authorization via a TAC contact will not be reimbursed. |
| Update Bulletin | 2017-11-03. Service bulletin. ENGINE; STRUCTURE. A quality package has been defined for Audi vehicles with 4.0L TFSI engine manufactured within a specific period. This Update is in effect until removed. Procedure is valid only for vehicles that show the 19J1 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicle must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. A quality package has been defined for Audi vehicles with 4.0L TFSI engine manufactured within a specific period. |
| Reference-Oil Ca | 2017-11-03. Service bulletin. ENGINE; EQUIPMENT; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This document contains the Audi oil capacity chart. |
| A871346 2035582- | 2017-11-03. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; ENGINE AND ENGINE COOLING. The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented. |
| A171347 2035463- | 2017-10-31. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 17 number 13-44 dated October 22, 2013. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine, and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, and the ambient temperature and road conditions. Additional factors include the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Utilizing the advanced sensor technology integrated in models equipped with the 3.0 TFSI engine, it is possible to measure oil consumption electronically via a Guided Function test plan. If the electronic oil consumption test is not available for this model, perform the test with the conventional scale/oil weighing method. See TSB 2018550 for instructions for the conventional scale/oil weighing method. |
| Update Bulletin- | 2017-10-31. Service bulletin. ENGINE AND ENGINE COOLING. A quality package has been defined for Audi vehicles with 4.0L TFSI engine manufactured within a specific period. This Update is in effect until removed. Procedure is valid only for vehicles that show the 19J1 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicle must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. quality package has been defined for Audi vehicles with 4.0L TFSI engine manufactured within a specific period. |
| A101310 2018288- | 2017-10-31. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 10 number 10-02 dated September 14, 2010. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the vehicle's engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these pieces are not removed prior to the installation and operation of the replacement engine, the pieces may be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage. |
| A011332 2035368- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM; ENGINE. MIL on. DTC P203B00 (Reductant Level Sensor Circuit Range/Performance) is stored in the engine control module (ECM), J623 (address word 01). Due to a production issue for the level sensor, the ECM cannot correctly read the Reductant (AdBlue) fluid level. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.