Service bulletins for the 2010 Audi A6
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
818 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Engine are shown. Show all
| A191346 2033491- | 2017-10-31. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM; ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 19 number 13-44 dated July 18, 2013. Customer may report coolant leaking from the engine area. The leak can be traced to the connection of the water pump and the hose leading to the heater core. The seal ring is not the cause of the leak. |
|---|---|
| A171346 2030197- | 2017-10-31. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM; ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 17 number 13-45 dated October 23, 2013. Customer complains of excessive oil consumption. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue, and the oxidation level of the oil. Under certain driving conditions, internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions, for example: stop and go traffic with extended idle periods. |
| A011348 2033001- | 2017-10-31. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 01 number 13-37 dated October 10, 2013. MIL on. DTCs are stored in the engine control module. Mileage is greater than 15,000 miles. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction. |
| A011345 2031458- | 2017-10-31. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 01 number 13-66 dated January 17, 2013. MIL on. DTCs are stored in the engine control module (ECM). Under extreme driving conditions (such short-distance, stop-and-go driving), high crankcase pressure can cause the DTCs to appear. The condition can be improved and the DTCs eliminated when the crankcase pressure valve is changed to a lower operating pressure and the ECM software is updated to compensate for new crankcase pressure. |
| A101310 2018288- | 2017-10-31. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 10 number 10-02 dated September 14, 2010. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the vehicle's engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these pieces are not removed prior to the installation and operation of the replacement engine, the pieces may be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage. |
| A011329 2033223- | 2017-10-31. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 01 number 13-73 dated March 7, 2013. The engine warning light is on after engine replacement. The engine is not running roughly. However, the engine control module, J623 (01), is storing one or more of the following engine misfire fault codes: DTCs P0300 - P0304. The fault codes occur at light load, between 8% and 14% accelerator pedal position. The programmed values for the misfiring recognition are not automatically reset by deleting the memory once. |
| A171345 2030197- | 2017-10-31. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 17 number 13-39 dated March 28, 2013. Customer complains of excessive oil consumption. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue, and the oxidation level of the oil. Under certain driving conditions, internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions, for example: stop and go traffic with extended idle periods. |
| A011337 2033001- | 2017-10-31. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 01 number 13-24 dated August 20, 2013. MIL on. DTCs are stored in the engine control module. Mileage is greater than 15,000 miles. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction. |
| Executive Servic | 2017-10-27. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE AND ENGINE COOLING; STEERING:HYDRAULIC POWER ASSIST:POWER STEERING FLUID; POWER TRAIN; SERVICE BRAKES, HYDRAULIC:FLUID. This document contains a fluid capacity chart as well as a chart that contains the parts and part numbers needed for service. |
| A171563 2038129- | 2017-10-27. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 17 number 14-53 dated November 7, 2014. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual. |
| A171555 2030197- | 2017-10-25. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 17 number 13-46 dated November 7, 2013. Customer complains of excessive oil consumption. Production solution is Crankcase pressure reduction starting with model year 2013. |
| A011507 2028344- | 2017-10-25. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 01 number 13-69 dated February 14, 2013. Noises and inconsistent engine operation after cold start during the catalyst heating phase. The customer may misinterpret these symptoms as engine misfiring. This bulletin applies only to non-diesel engines. |
| A171559 2030197- | 2017-10-25. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 17 number 15-55 dated February 9, 2015. Customer complains of excessive oil consumption. Crankcase pressure reduction starting with model year 2013. |
| A171561 2030197- | 2017-10-21. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 17 number 15-59 dated March 17, 2015. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner's Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue, and the oxidation level of the oil. Under certain driving conditions, internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions. |
| A171557 2010043- | 2017-10-21. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 17 number 13-35 dated January 9, 2013. This bulletin lists engine oils that meet Audi oil quality standards (VW 501 01, 502 00, 505 00, 505 01, and 504 00/507 00). |
| A101511 2018288- | 2017-10-21. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 10 number 13-10 dated September 5, 2013. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these metal debris pieces are not removed prior to the installation and operation of the replacement engine, they could be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage. |
| A011703 2033001- | 2017-10-04. Service bulletin. ENGINE. This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction. |
| A011701 2033001- | 2017-10-04. Service bulletin. ENGINE. This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction. |
| A01166520354544 | 2017-03-14. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. THIS TECHNICAL SERVICE BULLETIN CONTAINS INSTRUCTIONS FOR PRESSURE WASHING PORTS TO RESOLVE AN "AIR SYSTEM -- ACTION REQUIRED" MESSAGE. |
| A171673203019716 | 2017-02-23. Service bulletin. ENGINE; ELECTRICAL SYSTEM:SOFTWARE. THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO TEST FOR EXCESSIVE OIL CONSUMPTION AND UPDATE THE SOFTWARE IF NEEDED. |
| A01166520354544 | 2017-02-23. Service bulletin. ENGINE. THIS TECHNICAL SERVICE BULLETIN CONTAINS INSTRUCTIONS FOR PRESSURE WASHING PORTS TO RESOLVE AN "AIR SYSTEM -- ACTION REQUIRED" MESSAGE. |
| A01166920330018 | 2017-02-15. Service bulletin. ENGINE. THIS TEHCNIAL SERVICE BULLETIN PROVIDES CLEANING INSTRUCTIONS FOR CARBON ACCUMULATION IN THE SECONDARY AIR PORTS IN THE CYLINDER HEAD. |
| A01166920330018 | 2017-02-10. Service bulletin. ENGINE. THIS TEHCNIAL SERVICE BULLETIN PROVIDES CLEANING INSTRUCTIONS FOR CARBON ACCUMULATION IN THE SECONDARY AIR PORTS IN THE CYLINDER HEAD. |
| A171674203019717 | 2016-10-06. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM; ELECTRICAL SYSTEM:SOFTWARE. THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO TEST FOR EXCESSIVE OIL CONSUMPTION AND UPDATE THE SOFTWARE IF NEEDED. |
| SB-19I4 | 2016-05-23. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY. SUMMARY TO BE PROVIDED ON A FUTURE DATE. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.