Service bulletins for the 2010 Audi A4
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
912 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
| A171336 2030197- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 17 number 12-34 dated December 12, 2012. Customer complains of excessive oil consumption. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner's Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Under certain driving conditions, internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions, for example: stop and go traffic with extended idle periods. |
|---|---|
| A851316 2033596- | 2017-11-17. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. The fresh air blower is inoperative. DTCs may be stored in the heating and air conditioning electronics control module (address word 08). Malfunctions of the fresh air blower could be caused by a faulty printed circuit board in the fresh air blower control module and the carbon brushes bind in the brush holder and, as a consequence, lose contact with the motor commutator of the fresh air blower. |
| A281321 2017555- | 2017-11-17. Service bulletin. EQUIPMENT:ELECTRICAL. Supersedes Technical Service Bulletin Group 28 number 12-19 dated May 1, 2012. The master key with remote control does not engage or stay in the ignition lock. On vehicles without Advanced Key, the remote keys are inoperable. Keyless unlocking/locking using the door handle and keyless opening of the trunk lid using the trunk handle are inoperable. The vehicle cannot be started with the Start/Stop button. The remote keys are inoperable. The message "ignition lock faulty" may appear in the instrument cluster driver information display. DTC 00166 (Access/Start Authorization Switch -E415- Incorrect Signal) may be stored in Comfort System Central Control Module J393 (address word 46). It is possible that objects have been inserted into the ignition lock, which causes the slide of the ignition lock to become stuck in the rear part of the lock (S-contact position). The stuck slide is not allowed to return to the starting point (0-position). |
| A211313 2031245- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER. Supersedes Technical Service Bulletin Group 21 number 13-12 dated April 1, 2013. MIL on, DTC P0299 (Negative Pressure Deviation) is stored. Turbocharger waste gate flap has play. Under certain driving conditions, the linkage for the waste gate actuation can encounter excessive wear which leads to play at the waste gate flap. This leads to boost escaping through a loose flap, which sets DTC P0299 (Negative Pressure Deviation). |
| A211312 2031245- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER. Supersedes Technical Service Bulletin Group 21 number 13-11 dated March 6, 2013. MIL on, DTC P0299 (Negative Pressure Deviation) is stored. Turbocharger waste gate flap has play. Under certain driving conditions, the linkage for the waste gate actuation can encounter excessive wear which leads to play at the waste gate flap. This leads to boost escaping through a loose flap, which sets DTC P0299 (Negative Pressure Deviation). |
| A191336 2033491- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. Customer may report coolant leaking from the engine area. The leak can be traced to the connection of the water pump and the hose leading to the heater core. The seal ring is not the cause of the leak. |
| A011386 2033630- | 2017-11-17. Service bulletin. EQUIPMENT:ELECTRICAL; ENGINE. MIL on. Rough idle. DTCs are stored in the Engine Control Module (ECM), J623 (address word 01). Engine may have reduced performance without significant loss of power or stalling. Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced. |
| A001348 2002047- | 2017-11-17. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Supersedes Technical Service Bulletin Group 00 number 11-19 dated April 8, 2011. This TSB contains information on technician preparation when calling the Audi Technical Assistance Center |
| A011373 2033223- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. The engine warning light is on after engine replacement. The engine is not running roughly. However, the engine control module, J623 (01), is storing one or more of the following engine misfire fault codes: DTCs P0300 - P0304. The fault codes occur at light load, between 8% and 14% accelerator pedal position. The programmed values for the misfiring recognition are not automatically reset by deleting the memory once. |
| A011383 2033001- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:COOLING SYSTEM. MIL on. DTC P0491 and P0492 (Secondary Air System Insufficient Flow, Bank 1/2) are stored at the same time. Mileage is greater than 15,000 miles. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction. |
| A171337 2030197- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 17 number 13-36 dated February 14, 2013. Customer complains of excessive oil consumption. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner's Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Under certain driving conditions, internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions, for example: stop and go traffic with extended idle periods. |
| A171338 2012913- | 2017-11-17. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 17 number 10-07 dated June 3, 2010. Oil filter cartridge requires replacement. |
| A171339 2030197- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 17 number 13-37 dated March 13, 2013. Customer complains of excessive oil consumption. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Under certain driving conditions, internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions, for example: stop and go traffic with extended idle periods. |
| A191335 2025303- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 19 number 11-19 dated February 10, 2011. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service. |
| A211311 2031245- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER. Supersedes Technical Service Bulletin Group 21 number 12-10 dated October 25, 2012. MIL on, DTC P0299 (Negative Pressure Deviation) is stored. Turbocharger waste gate flap has play. Under certain driving conditions, the linkage for the waste gate actuation can encounter excessive wear which leads to play at the waste gate flap. This leads to boost escaping through a loose flap, which sets DTC P0299 (Negative Pressure Deviation). |
| A571385 2017082- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM; LATCHES/LOCKS/LINKAGES:DOORS:LATCH. Supersedes Technical Service Bulletin Group 57 number 13-82 dated February 5, 2013. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced. If other senders operate in the same frequency range (mobile phones, TV stations, wireless headphones, baby monitors, other vehicle remote controls, etc.), the remote control key may have been temporarily switched off because a clear identification of the remote control key is not possible. This is necessary to prevent an unintentional unlocking of the vehicle by other unrelated senders. |
| A571386 2027368- | 2017-11-17. Service bulletin. STRUCTURE:BODY:DOOR; LATCHES/LOCKS/LINKAGES:DOORS:LATCH. Supersedes Technical Service Bulletin Group 57 number 12-73 dated September 24, 2012. The exterior door handle touch sensors (Advanced key) are inoperative on one or several doors. The key blade can be used mechanically (driver door or trunk) or remote electrically (key remote buttons) to unlock and lock the vehicle. |
| A571387 2029151- | 2017-11-17. Service bulletin. LATCHES/LOCKS/LINKAGES:DOORS:LATCH; STRUCTURE:BODY:DOOR. Supersedes Technical Service Bulletin Group 57 number 12-80 dated November 9, 2012. The door cannot be opened from outside with the outer door handle, but it can be opened with the inner handle. The complaint is often described as follows: The customer locks the vehicle and checks by pulling the door handle whether the vehicle is locked. When opening the vehicle again, the door cannot be opened. It feels as if the handle is slack. |
| A851315 2033426- | 2017-11-17. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. The trim panel at the defroster vent on the instrument panel is deformed. The trim panel is composed of a material which expands in a moist condition. The instrument panel restricts this expansion which leads to deformation of the trim. |
| A941312 2017566- | 2017-11-17. Service bulletin. EXTERIOR LIGHTING:HEADLIGHTS:SWITCH; EXTERIOR LIGHTING:HEADLIGHTS. Supersedes Technical Service Bulletin Group 94 number 09-23 dated August 12, 2009. Headlight switch knob is pressed in. The switch functions correctly. The headlight switch knob was designed with a normal position and a pushed-in position. This is a deliberate design feature designed to avoid injuries in the event of a collision. |
| A971335 2033412- | 2017-11-17. Service bulletin. STEERING:ELECTRIC POWER ASSIST SYSTEM; STEERING. Steering wheel lock does not work. Various warning lights are on. Steering feels stiffer than usual. The engine cannot be switched off. The ignition key cannot be removed. DTC with description "Brake control unit, no signal/communication" is present in several control units. DTC entry in ABS Control unit, J104 (03). One or more may be present. This condition does not result in any drivability concerns. The steering system is fully connected. This condition does not result in any drivability concerns. The steering system is fully connected. The insulation for the ABS wheel speed sensor is damaged in production. Over time, this can lead to corrosion on the wires and restricted functions with the ABS control module. Only the wires in the left bulkhead grommet are affected. |
| Email Mandatory | 2017-11-17. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This document contains the important email to all Audi dealership personnel in regards to the immediate madatory stop-sale order that is in effect to all vehicles from 20110-2015 that have a 2.0L TDI engine. |
| A961501 2019260- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 96 number 13-67 dated July 10, 2013. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer?s door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. In A4 model years 2005?2006 and A3 model year 2009, the actual location of the garage door opener control module differs from the location shown in the owner's manual (opposite side of front bumper). The customer may misunderstand the programming procedure, particularly if the customer?s HomeLink® opener system is using an alternate code. The handheld transmitter?s programming function may become inoperative, or the transmitter is too far away from J530. Interference prevents the communication between handheld transmitter and J530. Interference prevents the communication between handheld transmitter and J530. If the vehicle flashes during the programming of a handheld transmitter, this does not necessarily indicate that the programming was successful; it only indicates that the vehicle has recognized and saved a signal. |
| A701547 2038029- | 2017-11-17. Service bulletin. VISIBILITY:SUN/MOON ROOF ASSEMBLY. Supersedes Technical Service Bulletin Group 70 number 15-44 dated February 25, 2015. Various squeaks and/or rattles are heard from the roof area on vehicles equipped with a panoramic sunroof. These noises can be created by the points of contact between the sunroof cover trim frame and the clips that retain it to the headliner. |
| A191562 2025303- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 19 number 15-61 dated July 7, 2015. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.