# Service bulletin NTB02007

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

- Type: Service bulletin
- NHTSA id: 629419
- Published by NHTSA: 2002\-04\-02
- Manufacturer's number: NTB02007
- Manufacturer's date: 2002\-01\-08
- NHTSA component: STRUCTURE:BODY:DOOR

## NHTSA's summary

CONCERNS WITH ALL DOORS INTERMITTENTLY LOCKING BY THEMSELVES. \*JB

## The document

No address for NHTSA's copy can be built for this communication. Ask the dealer for it by the manufacturer's number.

## Components

Body and frame

## Vehicles listed

- 2000 to 2002 NISSAN MAXIMA

## Other bulletins for the same vehicles and component

- [NTB09\-131C](/bulletins/11031705.md), 2026-04-29, Service bulletin: STRUCTURE:BODY. CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS \(Federal Motor Vehicle Safety Standards\) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” \(metal plate or vinyl label\) is attached to the instrument panel or body on the driver side at the base of the windshield \(see Figure 1\). · The “Certification Label” \(vinyl adhesive label\) is located on the lower area of the driver side B\-Pillar \(see Figure 1\).
- [NTB09\-131C](/bulletins/11031704.md), 2026-04-29, Service bulletin: STRUCTURE:BODY. CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS \(Federal Motor Vehicle Safety Standards\) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” \(metal plate or vinyl label\) is attached to the instrument panel or body on the driver side at the base of the windshield \(see Figure 1\). · The “Certification Label” \(vinyl adhesive label\) is located on the lower area of the driver side B\-Pillar \(see Figure 1\).
- [NTB13\-028H](/bulletins/10232658.md), 2023-03-07, Service bulletin: VISIBILITY; STRUCTURE. REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- [NTB09\-081J](/bulletins/10232656.md), 2023-03-07, Service bulletin: VISIBILITY; STRUCTURE. WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- [NTB01029](/bulletins/625091.md), 2001-11-16, Service bulletin: STRUCTURE:BODY:DOOR. SUBJECT REGARDING WIND NOISE REAR GLASS RUN RUBBER.
- [NTB00090](/bulletins/618788.md), 2001-04-30, Service bulletin: STRUCTURE:BODY:TRUNK LID. ON SOME VEHICLES, THE TRUNK ROOM SIDE FINISHER MAY POP OUT OF PLACE. \*TT
- [NTB99055A](/bulletins/613957.md), 2000-09-22, Service bulletin: STRUCTURE:BODY. CONCERNS WITH THE HEADLINER SAGGING AT THE SUNROOF RAILING ON VEHICLES BUILT BEFORE JN1CA31A4YT010384, JN1CA31A8YT209437, JN1CA31D0YT524517, JN1CA31D2YT7334418. \*TT
- [NTB00055](/bulletins/613954.md), 2000-09-22, Service bulletin: STRUCTURE:BODY:BUMPERS. VEHICLES BUILT BEFORE JN1CA31D1YT766295, JN1CA31A6YT224079, JN1CA31D5YT555214, JN1CA31A3YT031422 MAY HAVE A SCRATCH\(S\) IN THE TOP OF THE REAR BUMPER JUST BELOW THE LOWER EDGE OF THE TRUNK LID. \*TT
- [NTB99\-036A](/bulletins/613480.md), 2000-07-19, Service bulletin: STRUCTURE:BODY:DOOR. INFORMATION REGARDING KEYLESS REMOTE ENTRY PROGRAMMING. \*TT
- [NTB99046A](/bulletins/609979.md), 2000-04-12, Service bulletin: STRUCTURE:BODY:DOOR. CUSTOMERS MAY COMPLAIN THAT THE OUTER EDGE OF THE DOOR FINISHER CLOTH INSERTS ON ANY OF THE DOORS APPEAR ROUGH OR UNEVEN, OR IS NOT FULLY INSERTED INTO THE DOOR FINISHER. \*TT

JSON: [/v1/bulletins/629419](/v1/bulletins/629419)

[Report an error on this page](https://github.com/wenmar-pro/wenmar-open/issues/new?template=data_correction.yml&title=Data%20correction%3A%20Service%20bulletin%20NTB02007&page=https%3A%2F%2Fopen.wenmarpro.com%2Fbulletins%2F629419&vehicle=Service%20bulletin%20NTB02007)