# Service bulletin 180100

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

- Type: Service bulletin
- NHTSA id: 609988
- Published by NHTSA: 2000\-04\-12
- Manufacturer's number: 180100
- Manufacturer's date: 2000\-02\-04
- NHTSA component: ENGINE AND ENGINE COOLING:ENGINE

## NHTSA's summary

SUBJECT REGARDING MISDIAGNOSED LEAK DETECTION PUMP SYSTEMS WITH DIAGNOSTIC TROUBLE CODES P1494, P0442 P0455, OR P0456. \*TT

## The document

No address for NHTSA's copy can be built for this communication. Ask the dealer for it by the manufacturer's number.

## Components

Engine

## Trouble codes named

P0442, P0455, P0456, P1494

## Vehicles listed

- 1997 to 1998 CHRYSLER 300M
- 1999 to 2000 CHRYSLER 300M
- 1997 to 2000 CHRYSLER CIRRUS
- 1997 to 2000 CHRYSLER CONCORDE
- 1997 CHRYSLER LHS
- 1998 CHRYSLER LHS
- 1999 to 2000 CHRYSLER LHS
- 1997 to 2000 CHRYSLER SEBRING
- 1997 to 2000 CHRYSLER SEBRING CONVERTIBLE
- 1997 to 2000 CHRYSLER TOWN AND COUNTRY
- 1997 to 2000 DODGE AVENGER
- 1997 to 2000 DODGE CARAVAN
- 1997 to 2000 DODGE DAKOTA
- 1998 to 2000 DODGE DURANGO
- 1997 to 2000 DODGE INTREPID
- 1997 to 2000 DODGE NEON
- 1997 to 2000 DODGE RAM
- 1997 to 2000 DODGE RAM VAN
- 1997 to 2000 DODGE STRATUS
- 1997 to 2000 DODGE VIPER
- 1997 to 2000 DODGE VIPER GTS
- 1997 to 1998 EAGLE TALON
- 1999 to 2000 EAGLE TALON
- 1997 EAGLE VISION
- 1998 to 2000 EAGLE VISION
- 1997 to 2000 JEEP CHEROKEE
- 1997 to 2000 JEEP GRAND CHEROKEE
- 1997 to 2000 JEEP WRANGLER
- 1997 to 2000 PLYMOUTH BREEZE
- 1997 to 2000 PLYMOUTH NEON
- 1997 PLYMOUTH PROWLER
- 1998 PLYMOUTH PROWLER
- 1999 to 2000 PLYMOUTH PROWLER
- 1997 to 2000 PLYMOUTH VOYAGER

## Recalls for the same vehicles and component

- [06V199000](/recalls/nhtsa/06V199000.md), 2006-06-08: ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN
- [2002128](/recalls/tc/2002128.md), 2002-07-10: Engine
- [2002107](/recalls/tc/2002107.md), 2002-07-06: Engine
- [2002074](/recalls/tc/2002074.md), 2002-04-17: Engine
- [1998187](/recalls/tc/1998187.md), 1998-09-22: Engine
- [98V209000](/recalls/nhtsa/98V209000.md), 1998-09-08: ENGINE AND ENGINE COOLING:ENGINE:DIESEL
- [98V207000](/recalls/nhtsa/98V207000.md), 1998-09-08: ENGINE AND ENGINE COOLING:ENGINE:DIESEL
- [1998090](/recalls/tc/1998090.md), 1998-05-05: Engine

## Other bulletins for the same vehicles and component

- [05191925A](/bulletins/10228094.md), 2022-12-19, Service bulletin: ENGINE AND ENGINE COOLING. Radiator If vehicle comes in for transmission fluid leaking from trans\-oil cooler fittings on the radiator, please perform the following before replacing the radiator/cooler:\~ 1. Remove both of the transmission lines from the cooler?s top/bottom flared fittings on the radiator. \~ 2. Remove hex nut and the top flared fitting on the radiator tank.\~ 3. Using a wire brush and gasket remover, clean off the old sealant on the smaller threaded portion of the flared fitting. Do the same for the threads on the trans oil cooler.\~ 4. Apply a new application of Mopar PN 04318032 to the flared fitting, leaving the first threads free for ease of engagement.\~ 5. Install the top flared fitting by hand, then torque the fitting to 235 \+/\- 15 Lb\-In.\~ 6. Install the hex nut and torque to 100 \+/\- 10 Lb\-In.\~ 7. Repeat steps 2\-6 for bottom flared fitting.\~ 8. Reinstall transmission line per normal installation procedures and ensure correct fluid level.\~
- [68332810](/bulletins/10223854.md), 2022-10-17, Service bulletin: ENGINE AND ENGINE COOLING. Service \- Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY \- The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T\-joints.\~ 2. Fill the T\-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar® Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2\-mm \[0.063\-in\] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.\~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket\(s\) onto the oil pan flange.\~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2\-mm \[0.063\-in\] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.\~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 N·m \[21 ft. lbs.\].
- [R2118796A](/bulletins/10191460.md), 2021-05-03, Service bulletin: ENGINE AND ENGINE COOLING. Valve Body. These may cause over drive cycling.
- [68332810A](/bulletins/10191455.md), 2021-05-03, Service bulletin: ENGINE AND ENGINE COOLING. Cummins Equipped Vehicles ONLY \- The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only.
- [05191925A$](/bulletins/10181452.md), 2020-10-26, Service bulletin: EQUIPMENT; ENGINE AND ENGINE COOLING; POWER TRAIN. Radiator If vehicle comes in for transmission fluid leaking from trans\-oil cooler fittings on the radiator, please perform the following before replacing the radiator/cooler:\~ 1. Remove both of the transmission lines from the cooler?s top/bottom flared fittings on the radiator. \~ 2. Remove hex nut and the top flared fitting on the radiator tank.\~ 3. Using a wire brush and gasket remover, clean off the old sealant on the smaller threaded portion of the flared fitting. Do the same for the threads on the trans oil cooler.\~ 4. Apply a new application of Mopar PN 04318032 to the flared fitting, leaving the first threads free for ease of engagement.\~ 5. Install the top flared fitting by hand, then torque the fitting to 235 \+/\- 15 Lb\-In.\~ 6. Install the hex nut and torque to 100 \+/\- 10 Lb\-In.\~ 7. Repeat steps 2\-6 for bottom flared fitting.\~ 8. Reinstall transmission line per normal installation procedures and ensure correct fluid level.\~
- [9002688](/bulletins/10139009.md), 2018-06-04, Service bulletin: EQUIPMENT; ELECTRICAL SYSTEM:WIRING; ENGINE AND ENGINE COOLING. 68069384A$, R8069384A$, 68086182A$, R8027067A$, RL002012A$ \- Gasket, Cylinder Head Cover Before replacing injectors for Diagnostic Trouble Codes P0201, P0202, P0203, P0204, P0205, and/or P0206, please make sure that the wiring loom and/or connector in the valve cover gasket is not the root cause to your concern. In addition, make sure that the wiring attaching nuts are torqued to their proper value.\~
- [05191925A$](/bulletins/10121923.md), 2017-11-03, Service bulletin: POWER TRAIN; ENGINE. Radiator If vehicle comes in for transmission fluid leaking from trans\-oil cooler fittings on the radiator, please check the following before replacing the radiator/cooler:\~ 1. Remove both of the transmission lines from the cooler?s top/bottom flared fittings on the radiator. \~ 2. Loosen the hex nut on the top flared fitting on the radiator tank.\~ 3. Torque the top flared fitting to 235 \+/\- 15 Lb\-In.\~ 4. Torque hex nut to 100 \+/\- 10 Lb\-In.\~ 5. Repeat for bottom flared fitting.\~ 6. Reinstall transmission line per normal installation procedures and ensure correct fluid level.\~ \~ If vehicle is in need of a new radiator for another reason, check the new radiator for correct torque on the trans\-oil cooler fitting per steps 2\-5 above.\~ \~ If radiator has a yellow mark by the trans\-oil cooler fittings the torque does not have to be checked.
- [22](/bulletins/10020666.md), 2006-12-08, Service bulletin: ENGINE AND ENGINE COOLING:ENGINE. REPROGRAM PCM AND INSPECT CATALYTIC CONVERTER. \*KB
- [1100605](/bulletins/10018993.md), 2006-01-27, Service bulletin: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. ILLUMINATED MIL AS THE RESULT OF A DIAGNOSTIC TROUBLE CODE \(DTC\) P0420 \- CATALYST EFFICIENCY, OR MAY HAVE FAILED A CALIFORNIA SMOG OR STATE I/M TEST BUT WITHOUT AN ILLUMINATED MIL, OR A RATTLING SOUND FROM THE UNDERSIDE OF THE VEHICLE. CATALYTIC CONVERTER EXTENDED WARRANTY TO REPLACE THE CATALYTIC CONVERTER. \*TT
- [1100505](/bulletins/10018976.md), 2006-01-26, Service bulletin: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. RATTLING SOUND FROM THE UNDERSIDE OF THE VEHICLE. CATALYTIC CONVERTER EXTENDED WARRANTY TO REPLACE THE CATALYTIC CONVERTER. \*TT

JSON: [/v1/bulletins/609988](/v1/bulletins/609988)

[Report an error on this page](https://github.com/wenmar-pro/wenmar-open/issues/new?template=data_correction.yml&title=Data%20correction%3A%20Service%20bulletin%20180100&page=https%3A%2F%2Fopen.wenmarpro.com%2Fbulletins%2F609988&vehicle=Service%20bulletin%20180100)