# Service bulletin LI46.80\-P\-080662

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

- Type: Service bulletin
- NHTSA id: 11033168
- Published by NHTSA: 2026\-06\-02
- Manufacturer's number: LI46.80\-P\-080662
- Manufacturer's date: 2026\-06\-01
- NHTSA component: STEERING

## NHTSA's summary

Complaint Rattling/knocking noise from the rear axle steering is audible when driving on rough terrain or cobblestones. Large play in the rear axle steering. Cause Diverse functional play in the rear axle steering. Remedy 1. Detach underfloor paneling under rear axle steering. 2. Unscrew both holders of the rear muffler on the exhaust system and lower the rear muffler 3. Remove heat shield. 4. Remove large clamps from left bellows. 5. Slide bellows to side. The bellows can be pulled outwards to work on the screw\-on stud. 6. A second person sits in the vehicle and, with the drive activated and the automatic transmission in the N position, turns the steering to left lock. Caution\! Risk of trapping when steering at the same time\! Do not move steering wheel during operation steps 7 and 8\! 7. Clean screw\-on stud of any grease using a clean, lint\-free rag. =\> Up to the area where the stud enters the bearing\! Then completely degrease the threaded stud using a lint\-free cloth soaked in a suitable assembly cleaner \(e.g., A 000 986 56 01\); if necessary, clean hard\-to\-reach areas with the assembly cleaner. =\> Up to the area where the stud enters the bearing\! Important:The surface must be thoroughly cleaned and free of grease\! 8. Then apply Hylomar \(A 001 989 25 20 09\) all around to the degreased screw\-on stud using a new brush. =\> Up to the area where the stud enters the bearing\! 9. Move steering wheel from end stop to end stop 1\-2 times. Then, turn the steering to the left lock again. Warning\! Risk of trapping when steering at the same time\! 10. Then apply Hylomar again. 11. Move steering wheel from end stop to end stop 1\-2 times. Then, turn the steering to the right lock. Warning\! Risk of trapping when steering at the same time\! 12. Bellows installation: Coat contact surfaces of bellows and rack\-and\-pinion steering lightly with Renolit \(A094 989 38 00\). When doing so, ensure that the grease is underneath the edges of the bellows. Replace large clamps \(A 000 995 89 08\). 13. Repeat operation steps 4 to 5 on the other side. 14. Then repeat operation steps 7 to 12 for the screw\-on stud on the other side. 15. Attach heat shield. 16. Install both holders of the rear muffler again. 17. Attach underfloor paneling. 18. When relocating the vehicle on the premises, please use Snow Chain Mode through the head unit. 19. Leave the Hylomar to dry for approx. 90 minutes. Note:Deactivate Snow Chain Mode after stopping the vehicle\! 20. Then perform a test drive. If applying it does not resolve the problem alone, continue with the following additional steps: 1. Align vehicle and adjust track of the front and rear axle 2. Leave vehicle on axle alignment platform or drive onto another drive\-on ramp lift. Vehicle must rest entirely on its wheels without relieving the load on the axles\! 3. Mark the position of the eccentric screw connection between the tie rod and the tie rod mount on the rear axle steering/fork on the left and right using a thin marker. \(See example in the picture: red marking between eccentric disk “B” and rear axle steering tie rod mount/fork “D”\). 4. Now loosen these threaded connections on the left and right until the screws can be twisted easily. The rubber mount relaxes. 5. Connect Xentry Diagnostics. 6. Get started in the AIRMATIC control unit \(N51/8\) and call up the "Lifting and lowering the rear axle" menu item. Use the "Lifting and lowering the rear axle" menu to lift the rear axle. Raise the level of the vehicle to 95 mm using the "\+" button \(see picture\). Wheels are still on the platform. Check the gauge in Xentry Diagnostics to see when the required level has been reached. 7. In this raised position, replace the nuts of both threaded connections, but do not tighten the nuts. Then, with the threaded connection still loosened, turn the eccentric screws / disks "B" back to the mark, as in the initial situation. Then tighten the screws with the required torque. 8. Lower the rear axle to the vehicle\-specific normal level with Xentry

## The document

- [NHTSA's copy of the document (PDF)](https://static.nhtsa.gov/odi/tsbs/2026/MC-11033168-0001.pdf)
- [If that address does not open, try this one](https://static.nhtsa.gov/odi/tsbs/2026/MC-11033168-9999.pdf)

The document is the manufacturer's. This site does not hold it.

## Components

Steering

## Vehicles listed

- 2023 to 2024 MERCEDES\-BENZ AMG C43
- 2023 to 2026 MERCEDES\-BENZ AMG C43 4MATIC
- 2024 MERCEDES\-BENZ AMG C63 S E
- 2024 to 2025 MERCEDES\-BENZ AMG C63 S E 4MATIC\+
- 2026 MERCEDES\-BENZ AMG C63 S E PERFORMANCE 4MATIC\+
- 2025 MERCEDES\-BENZ AMG E 53 E 4MATIC\+
- 2024 to 2026 MERCEDES\-BENZ AMG GLC43
- 2024 to 2026 MERCEDES\-BENZ AMG GLC43 4MATIC
- 2024 to 2025 MERCEDES\-BENZ AMG GLC43 4MATIC COUPE
- 2026 MERCEDES\-BENZ AMG GLC43 COUPE
- 2025 MERCEDES\-BENZ AMG GLC63 S E
- 2025 to 2026 MERCEDES\-BENZ AMG GLC63 S E 4MATIC\+
- 2025 to 2026 MERCEDES\-BENZ AMG GLC63 S E 4MATIC\+ COUPE
- 2022 to 2026 MERCEDES\-BENZ C 300
- 2022 to 2026 MERCEDES\-BENZ C 300 4MATIC
- 2024 to 2026 MERCEDES\-BENZ E 350
- 2024 to 2026 MERCEDES\-BENZ E 350 4MATIC
- 2024 MERCEDES\-BENZ E 450
- 2024 to 2026 MERCEDES\-BENZ E 450 4MATIC
- 2024 to 2026 MERCEDES\-BENZ E 450 4MATIC ALL\-TERRAIN
- 2020 MERCEDES\-BENZ E 450 4MATIC CABRIOLET
- 2020 MERCEDES\-BENZ E 450 4MATIC COUPE
- 2020 MERCEDES\-BENZ E 450 4MATIC WAGON
- 2025 MERCEDES\-BENZ E53 E 4MATIC\+
- 2026 MERCEDES\-BENZ E53 E 4MATIC\+ ALL\-TERRAIN
- 2023 to 2026 MERCEDES\-BENZ GLC 300
- 2023 to 2026 MERCEDES\-BENZ GLC 300 4MATIC
- 2024 to 2026 MERCEDES\-BENZ GLC 300 4MATIC COUPE
- 2024 MERCEDES\-BENZ GLC 300 COUPE
- 2025 MERCEDES\-BENZ GLC 300E
- 2025 to 2026 MERCEDES\-BENZ GLC 350 E 4MATIC
- 2026 MERCEDES\-BENZ GLC43 4MATIC COUPE

JSON: [/v1/bulletins/11033168](/v1/bulletins/11033168)

[Report an error on this page](https://github.com/wenmar-pro/wenmar-open/issues/new?template=data_correction.yml&title=Data%20correction%3A%20Service%20bulletin%20LI46.80-P-080662&page=https%3A%2F%2Fopen.wenmarpro.com%2Fbulletins%2F11033168&vehicle=Service%20bulletin%20LI46.80-P-080662)