WenmarOpen by Wenmar Pro

Service bulletin SSM 54054

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id11020889
Published by NHTSA2025-07-24
Manufacturer's numberSSM 54054
Manufacturer's date2025-07-16
NHTSA componentELECTRICAL SYSTEM; POWER TRAIN

NHTSA's summary

Some 2025 Transit vehicles with gasoline or flex fuel engines may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P0773 and/or P097E stored in the powertrain control module (PCM). These vehicles may also exhibit various other powertrain related DTCs setting in the PCM. This may be due to pushed out pins and/or poor terminal crimping at connector C1280. Refer to Wiring Diagram Cell 30-5 for location information.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Electrical system, Transmission and driveline

Trouble codes named

C1280, P0773, P097E

Vehicles listed
FORD TRANSIT2025

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Other bulletins for the same vehicles and component
SSM 550312026-07-28. Service bulletin. Some 2021-2026 Ford/Lincoln vehicles may exhibit various symptoms including but not limited to the auto start/stop system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is operating properly with no charging related diagnostic trouble codes (DTC) stored. This may be due to someone using an aftermarket programmer to change the body control module (BCM) configuration to disable the auto start/stop system or perform other unsupported programming modifications. To correct this condition on F-150 and Bronco vehicles, download and run the Ford Diagnosis and Repair System (FDRS) application titled "BCM-Charging System Configuration Correction". Running this application will determine if the BCM configuration was modified by the customer and if so, provide the option to return the configuration back to factory settings. For other vehicle models exhibiting concerns related to unsupported aftermarket BCM programming, submit a Technical Support Request (TSR) requesting support to revert the BCM configuration
SSM 550082026-07-20. Service bulletin. Some 2021-2026 Ford vehicles may exhibit inoperative heated/cooled seats, heated steering wheel and/or front/rear defrost features after a remote start is performed through the Ford mobile application or with the key fob. Customers may also experience heated/cooled seats, heated steering wheel and/or front/rear defrost features turning on in unexpected conditions such as during warmer weather. These features will operate normally when commanded in the center display screen. This may be due to the customer not setting up their "Climate Settings" through the Ford mobile application. To correct this condition, inform the customer they should perform a remote start from the Ford mobile application and then adjust the "Climate Settings" in the Ford mobile application as desired. These settings only need to be set once and will persist through subsequent remote starts. Heated and cooled seats will be set to Level 2 when turned ON via "Climate Settings" in the Ford mobile application during a remote start event. This is normal operating characteristic. This condition does not affect vehicle durability and no a
TSB 26-22632026-06-05. Service bulletin. This bulletin supersedes 26-2112. Reason For Update: add 2026 model year vehicles, update LV fluid XT-10-QLVC and CXT-10-LV6 description to add "Transfer Case Fluid 4WD Only", and update Step 4 to inspect/replace 7H351 and 7B177 outside of this article. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - No upshift past second gear - Unable to achieve third gear ratio - Illuminated MIL with DTCs P0757 and P2701 This may be due to a damaged one-way clutch (OWC).
25N122026-04-30. Other. Customer Satisfaction Program 25N12 Certain 2020-2025 Model Year Transit All-Wheel-Drive (AWD) Vehicles Transfer Case Replacement If Required After Dealer Evaluation
SSM 547652026-04-28. Service bulletin. Some 2025-2026 Bronco, Bronco Sport, F-Super Duty, Maverick, Mustang, Mustang Mach-E, Ranger and Transit vehicles may exhibit a no audio/sound condition. This may be due to the software in the audio control module (ACM). To determine if it is a software concern, disconnect the vehicle's 12-volt battery cables for 10 minutes and reconnect. If the concern is still present, continue with normal diagnostics in Workshop Manual (WSM), Section 415-00 Information and Entertainment System > General Information > Diagnosis and Testing and repair as necessary outside of this article. If the no audio/sound concern is resolved, engineering is currently working on a solution for this condition that is expected by September 2026. Replacement or reprogramming of the ACM and or audio digital signal processing module (DSP) may not resolve this condition at this time. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available. If a customer's vehicle exhibits this concern, submit a Vehicle Concern Report.
SSM 547382026-04-14. Service bulletin. Some 2023-2025 Escape 1.5L/F-Super Duty/Transit vehicles may exhibit a lack of cooling from the heating, ventilation, and air conditioning (HVAC) system, which may be accompanied by abnormal rattling, grinding and/or squealing noises from the engine compartment. This may be due to damage to the air conditioning (A/C) compressor internal components and/or clutch assembly. Confirm ambient air temperature is above approximately 0°C (32.0°F). On the HVAC controls, set the temperature to full cold (not MAX A/C), select PANEL, set the fan speed to the highest setting and select the A/C button (indicator on). If the A/C compressor clutch engages and the A/C compressor is noisy, and/or the belt is slipping on the A/C compressor pulley or the A/C compressor is seized, install a new A/C compressor as indicated in Section 412-00 of the Workshop Manual (WSM). For claiming, use causal part 19703 and labor operation MT19700SSM up to 0.3 hours to check for a damaged compressor. If the compressor requires replacement, claim labor operations 19700A and 19700A4. Also claim available Service Labor Time Standards (SLTS) op
SSM 547202026-04-10. Service bulletin. Various 2020-2026 Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
SSM 547192026-04-10. Service bulletin. For 20212026 vehicles equipped with the 10R80 transmission, a new Transmission Clutch Circuit Leak Test has been introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. When referred to a specific clutch (A-F) test by a pinpoint test in Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing, the Clutch Assembly tests have been updated with a hyperlink to the new Transmission Line Pressure Test - Pressure Vacuum Transducer (PVT) Is Available procedure in WSM, Section 307-01 > General Procedures. This procedure provides instructions to perform the FDRS Transmission Clutch Circuit Leak Test when applicable. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method. The previous air check procedure has been shown to produce a high rate of false positives, which may lead to unnecessary repairs when no actual leak is present. Accordingly, the air check procedure is not to be used for diagnosing internal transmission hydraulic leaks or as justification
SSM 546742026-04-06. Service bulletin. For 2021-2026 vehicles equipped with the 10R80 transmission, a new Transmission Clutch Circuit Leak Test has been introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. The Workshop Manual (WSM) has been updated under Section 307-01 > Diagnosis and Testing to include this procedure. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method.
TSB 26-21122026-03-23. Service bulletin. This bulletin supersedes TSB 26-2059. Reason For Update: To add missing labor operations. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - No upshift past second gear - Unable to achieve third gear ratio - Illuminated malfunction indicator lamp (MIL) with DTCs P0757 and P2701 This may be due to a damaged one-way clutch (OWC).