# Service bulletin 9100565 Rev 1

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

- Type: Service bulletin
- NHTSA id: 11020604
- Published by NHTSA: 2025\-07\-09
- Manufacturer's number: 9100565 Rev 1
- Manufacturer's date: 2025\-07\-01
- NHTSA component: ENGINE

## NHTSA's summary

C0582\-00\-BRAKE BOOSTER MOTOR "A" PHASE U\-V\-W CIRCUIT RANGE/PERFORMANCE C058A\-00\-BRAKE BOOSTER MOTOR "A" POSITION SENSOR CIRCUIT RANGE/PERFORMANCE C058E\-00\-BRAKE BOOSTER MOTOR "B" POSITION SENSOR CIRCUIT RANGE/PERFORMANCE After performing the diagnostic tests and determines to replace the Brake System Control Module \(BSCM\) also replace the EBooster. \(Send back both Brake Electronic Control Unit and Hydraulic Control Unit for Engineering Analysis\) To avoid potential charge\-back, only use MOPAR approved brake fluid per the service manual. When filling the brake reservoir, use clean equipment and gloves during repair to avoid cross\-contamination.

## The document

- [NHTSA's copy of the document (PDF)](https://static.nhtsa.gov/odi/tsbs/2025/MC-11020604-0001.pdf)
- [If that address does not open, try this one](https://static.nhtsa.gov/odi/tsbs/2025/MC-11020604-9999.pdf)

The document is the manufacturer's. This site does not hold it.

## Components

Engine

## Vehicles listed

- 2022 to 2025 JEEP GRAND WAGONEER
- 2022 to 2025 JEEP WAGONEER

## Other bulletins for the same vehicles and component

- [18\-083\-26](/bulletins/11038540.md), 2026-10-16, Service bulletin: ENGINE. Flash: Powertrain Control Module \(PCM\) Updates Customers must experience a Malfunction Indicator Lamp \(MIL\) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes \(DTCs\): ● \*\*P2237\-00 \- O2 Sensor Positive Current Control Circuit/Open Bank 1 Sensor 1. ● P2240\-00 \- O2 Sensor Positive Current Control Circuit/Open Bank 2 Sensor 1. ● P2251\-00 \- O2 Sensor Negative Current Control Circuit/Open Bank 1 Sensor 1. ● P2254\-00 \- O2 Sensor Negative Current Control Circuit/Open Bank 2 Sensor 1. ● P2243\-00 \- O2 Sensor Reference Voltage Circuit/Open Bank 1 Sensor 1. ● P2247\-00 \- O2 Sensor Reference Voltage Circuit/Open Bank 2 Sensor 1. ● P015B\-00 \- O2 Sensor Delayed Response \- Lean To Rich Bank 1 Sensor 1. ● P015D\-00 \- O2 Sensor Delayed Response \- Lean To Rich Bank 2 Sensor 1. ● P2AF6\-00 \- Starter Relay 3 Stuck Off. ● P0E7C\-00 \- Coolant Bypass Valve "B" Control Circuit Low. ● P0E7D\-00 \- Coolant Bypass Valve "B" Control Circuit High. ● P0E7E\-00 \- Coolant Bypass Valve "B" Control Circuit Range/Performance. ● P0E7F\-00 \- Coolant Bypass Valve "B" Control Circuit Stuck/Open. ● U063C\-00 \- Lost Communication With Coolant Bypass Valve Actuator "B". ● P0100\-00 \- Mass Or Volume Air Flow Sensor "A" Circuit. ● P0101\-00 \- Mass Or Volume Air Flow Sensor "A" Circuit Range/Performance. ● P0461\-00 \- Fuel Level Sensor "A" Circuit Range/performance. ● P0073\-00 \- Ambient Air Temperature Sensor Circuit "A" High. ● P0072\-00 \- Ambient Air Temperature Sensor Circuit "A" Low. ● P062B\-00 \- Internal Control Module Fuel Injector Control Performance. ● B1810\-00 \- Driver Door Shorted Low. ● B25C7\-00 \- Redundant Driver Door Shorted Low.\*\* ● U0673\-00 \- Lost Communication With Ion Sense Module \(in active or stored status\). ● P00C6\-00 \- Fuel Rail Pressure Too Low \- Engine Cranking \(in active or stored status\). ● P2C90\-00 \- Crankcase Ventilation System \- Hose "A" Disconnected \(in active or stored status\). This bulletin involves inspecting and possibly reprogramming the PCM with the latest available software.
- [18\-082\-26](/bulletins/11038539.md), 2026-10-16, Service bulletin: ENGINE. Flash: Powertrain Control Module \(PCM\) Updates Customers must experience a Malfunction Indicator Lamp \(MIL\) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes \(DTCs\): ● \*\*P2237\-00 \- O2 Sensor Positive Current Control Circuit/Open Bank 1 Sensor 1. ● P2240\-00 \- O2 Sensor Positive Current Control Circuit/Open Bank 2 Sensor 1. ● P2251\-00 \- O2 Sensor Negative Current Control Circuit/Open Bank 1 Sensor 1. ● P2254\-00 \- O2 Sensor Negative Current Control Circuit/Open Bank 2 Sensor 1. ● P2243\-00 \- O2 Sensor Reference Voltage Circuit/Open Bank 1 Sensor 1. ● P2247\-00 \- O2 Sensor Reference Voltage Circuit/Open Bank 2 Sensor 1. ● P015B\-00 \- O2 Sensor Delayed Response \- Lean To Rich Bank 1 Sensor 1. ● P015D\-00 \- O2 Sensor Delayed Response \- Lean To Rich Bank 2 Sensor 1. ● P2AF6\-00 \- Starter Relay 3 Stuck Off. ● P0E7C\-00 \- Coolant Bypass Valve "B" Control Circuit Low. ● P0E7D\-00 \- Coolant Bypass Valve "B" Control Circuit High. ● P0E7E\-00 \- Coolant Bypass Valve "B" Control Circuit Range/Performance. ● P0E7F\-00 \- Coolant Bypass Valve "B" Control Circuit Stuck/Open. ● U063C\-00 \- Lost Communication With Coolant Bypass Valve Actuator "B". ● P0100\-00 \- Mass Or Volume Air Flow Sensor "A" Circuit. ● P0101\-00 \- Mass Or Volume Air Flow Sensor "A" Circuit Range/Performance. ● P0461\-00 \- Fuel Level Sensor "A" Circuit Range/performance. ● P0073\-00 \- Ambient Air Temperature Sensor Circuit "A" High. ● P0072\-00 \- Ambient Air Temperature Sensor Circuit "A" Low. ● P062B\-00 \- Internal Control Module Fuel Injector Control Performance. ● B1810\-00 \- Driver Door Shorted Low. ● B25C7\-00 \- Redundant Driver Door Shorted Low.\*\* ● U0673\-00 \- Lost Communication With Ion Sense Module \(in active or stored status\). ● P00C6\-00 \- Fuel Rail Pressure Too Low \- Engine Cranking \(in active or stored status\). ● P2C90\-00 \- Crankcase Ventilation System \- Hose "A" Disconnected \(in active or stored status\). This bulletin involves inspecting and possibly reprogramming the PCM with the latest available software.
- [18\-083\-26](/bulletins/11038503.md), 2026-10-16, Service bulletin: ENGINE. Flash: Powertrain Control Module \(PCM\) Updates Customers must experience a Malfunction Indicator Lamp \(MIL\) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes \(DTCs\): ● \*\*P2237\-00 \- O2 Sensor Positive Current Control Circuit/Open Bank 1 Sensor 1. ● P2240\-00 \- O2 Sensor Positive Current Control Circuit/Open Bank 2 Sensor 1. ● P2251\-00 \- O2 Sensor Negative Current Control Circuit/Open Bank 1 Sensor 1. ● P2254\-00 \- O2 Sensor Negative Current Control Circuit/Open Bank 2 Sensor 1. ● P2243\-00 \- O2 Sensor Reference Voltage Circuit/Open Bank 1 Sensor 1. ● P2247\-00 \- O2 Sensor Reference Voltage Circuit/Open Bank 2 Sensor 1. ● P015B\-00 \- O2 Sensor Delayed Response \- Lean To Rich Bank 1 Sensor 1. ● P015D\-00 \- O2 Sensor Delayed Response \- Lean To Rich Bank 2 Sensor 1. ● P2AF6\-00 \- Starter Relay 3 Stuck Off. ● P0E7C\-00 \- Coolant Bypass Valve "B" Control Circuit Low. ● P0E7D\-00 \- Coolant Bypass Valve "B" Control Circuit High. ● P0E7E\-00 \- Coolant Bypass Valve "B" Control Circuit Range/Performance. ● P0E7F\-00 \- Coolant Bypass Valve "B" Control Circuit Stuck/Open. ● U063C\-00 \- Lost Communication With Coolant Bypass Valve Actuator "B". ● P0100\-00 \- Mass Or Volume Air Flow Sensor "A" Circuit. ● P0101\-00 \- Mass Or Volume Air Flow Sensor "A" Circuit Range/Performance. ● P0461\-00 \- Fuel Level Sensor "A" Circuit Range/performance. ● P0073\-00 \- Ambient Air Temperature Sensor Circuit "A" High. ● P0072\-00 \- Ambient Air Temperature Sensor Circuit "A" Low. ● P062B\-00 \- Internal Control Module Fuel Injector Control Performance. ● B1810\-00 \- Driver Door Shorted Low. ● B25C7\-00 \- Redundant Driver Door Shorted Low.\*\* ● U0673\-00 \- Lost Communication With Ion Sense Module \(in active or stored status\). ● P00C6\-00 \- Fuel Rail Pressure Too Low \- Engine Cranking \(in active or stored status\). ● P2C90\-00 \- Crankcase Ventilation System \- Hose "A" Disconnected \(in active or stored status\). This bulletin involves inspecting and possibly reprogramming the PCM with the latest available software.
- [18\-082\-26](/bulletins/11038502.md), 2026-10-16, Service bulletin: ENGINE. Flash: Powertrain Control Module \(PCM\) Updates Customers must experience a Malfunction Indicator Lamp \(MIL\) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes \(DTCs\): ● \*\*P2237\-00 \- O2 Sensor Positive Current Control Circuit/Open Bank 1 Sensor 1. ● P2240\-00 \- O2 Sensor Positive Current Control Circuit/Open Bank 2 Sensor 1. ● P2251\-00 \- O2 Sensor Negative Current Control Circuit/Open Bank 1 Sensor 1. ● P2254\-00 \- O2 Sensor Negative Current Control Circuit/Open Bank 2 Sensor 1. ● P2243\-00 \- O2 Sensor Reference Voltage Circuit/Open Bank 1 Sensor 1. ● P2247\-00 \- O2 Sensor Reference Voltage Circuit/Open Bank 2 Sensor 1. ● P015B\-00 \- O2 Sensor Delayed Response \- Lean To Rich Bank 1 Sensor 1. ● P015D\-00 \- O2 Sensor Delayed Response \- Lean To Rich Bank 2 Sensor 1. ● P2AF6\-00 \- Starter Relay 3 Stuck Off. ● P0E7C\-00 \- Coolant Bypass Valve "B" Control Circuit Low. ● P0E7D\-00 \- Coolant Bypass Valve "B" Control Circuit High. ● P0E7E\-00 \- Coolant Bypass Valve "B" Control Circuit Range/Performance. ● P0E7F\-00 \- Coolant Bypass Valve "B" Control Circuit Stuck/Open. ● U063C\-00 \- Lost Communication With Coolant Bypass Valve Actuator "B". ● P0100\-00 \- Mass Or Volume Air Flow Sensor "A" Circuit. ● P0101\-00 \- Mass Or Volume Air Flow Sensor "A" Circuit Range/Performance. ● P0461\-00 \- Fuel Level Sensor "A" Circuit Range/performance. ● P0073\-00 \- Ambient Air Temperature Sensor Circuit "A" High. ● P0072\-00 \- Ambient Air Temperature Sensor Circuit "A" Low. ● P062B\-00 \- Internal Control Module Fuel Injector Control Performance. ● B1810\-00 \- Driver Door Shorted Low. ● B25C7\-00 \- Redundant Driver Door Shorted Low.\*\* ● U0673\-00 \- Lost Communication With Ion Sense Module \(in active or stored status\). ● P00C6\-00 \- Fuel Rail Pressure Too Low \- Engine Cranking \(in active or stored status\). ● P2C90\-00 \- Crankcase Ventilation System \- Hose "A" Disconnected \(in active or stored status\). This bulletin involves inspecting and possibly reprogramming the PCM with the latest available software.
- [9100861 Rev 3](/bulletins/11035994.md), 2026-08-06, Service bulletin: ENGINE. PUMP, Auxiliary Coolant Before replacing the Auxiliary Coolant Pump, please perform the following steps: 1\) Key ON/OFF and let the after\-run pump run for at least 20 minutes before moving on to step \#2. 2\) Inspect the pump connector area for presence of water. 3\) Inspect the pump connector for corrosion. 4\) Inspect the pump for coolant contamination as this can cause the pump to stall. 5\) Inspect battery terminals for damage to rule out a battery drainage issue. 6\) Ensure the PCM is up\-to\-date with the latest available flash. If correct repair is not performed then the claim or condition will be recovered by Warranty Operations.
- [9100861 Rev 1](/bulletins/11035194.md), 2026-07-23, Service bulletin: ENGINE. PUMP, Auxiliary Coolant Before replacing the Auxiliary Coolant Pump, please perform the following steps: 1\) Key ON/OFF and let the after\-run pump run for at least 20 minutes before moving on to step \#2. 2\) Inspect the pump connector area for presence of water. 3\) Inspect the pump connector for corrosion. 4\) Inspect the pump for coolant contamination as this can cause the pump to stall. 5\) Inspect battery terminals for damage to rule out a battery drainage issue. 6\) Ensure the PCM is up\-to\-date with the latest available flash.
- [9100861](/bulletins/11035070.md), 2026-07-18, Service bulletin: ENGINE; ELECTRICAL SYSTEM. PUMP, Auxiliary Coolant Before replacing the Auxiliary Coolant Pump, please perform the following steps: 1\) Key ON/OFF and let the after\-run pump run for at least 20 minutes before moving on to step \#2. 2\) Inspect the pump connector area for presence of water. 3\) Inspect the pump connector for corrosion. 4\) Inspect the pump for coolant contamination as this can cause the pump to stall. 5\) Ensure the PCM is up\-to\-date with the latest available flash. 6\) Inspect battery terminals for damage to rule out a battery drainage issue.
- [9100832](/bulletins/11033959.md), 2026-06-18, Service bulletin: ENGINE; ELECTRICAL SYSTEM. Before replacing the starter, please follow the published diagnostics in the Service Information at 08 \- Electrical / 8F \- Engine Systems / Starting / Diagnosis and Testing / STANDARD STARTING SYSTEM. Updates to this procedure have been recently made and should be followed.
- [112037](/bulletins/11032859.md), 2026-05-20, Service bulletin: ENGINE. MODULE \- IGNITION
- [9100790](/bulletins/11030427.md), 2026-04-01, Service bulletin: ENGINE. Before replacing the water pump on 3.0L SO/HO, please follow the updated WATER PUMP INSPECTION diagnostic procedure to confirm the leak persists "09 \- Engine, 3.0L GMET6 / Cooling System / Engine Cooling / Diagnosis and Testing / COOLING SYSTEM LEAKS"

JSON: [/v1/bulletins/11020604](/v1/bulletins/11020604)

[Report an error on this page](https://github.com/wenmar-pro/wenmar-open/issues/new?template=data_correction.yml&title=Data%20correction%3A%20Service%20bulletin%209100565%20Rev%201&page=https%3A%2F%2Fopen.wenmarpro.com%2Fbulletins%2F11020604&vehicle=Service%20bulletin%209100565%20Rev%201)