# Service bulletin LI72.10\-P\-069496

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

- Type: Service bulletin
- NHTSA id: 11013305
- Published by NHTSA: 2025\-01\-31
- Manufacturer's number: LI72.10\-P\-069496
- Manufacturer's date: 2025\-01\-24
- NHTSA component: ELECTRICAL SYSTEM

## NHTSA's summary

Complaint Windows of the front doors poorly adjusted/sluggish Cause The settings of the front windows may be set incorrectly Remedy Adjustment of the windows or window guides as specified in AR72.10\-P\-1960GQS . A video with further information on instructions can be found in the attachment. Description of the videos: Safety Information: 1. AS00.00\-Z\-0011\-01A Risk of injury with trapped or crushed fingers when performing removal/installation and adjustment work on hoods, doors, lids and sliding roof 2. AH67.00\-P\-0003\-01FB Notes on avoiding damage to glass and windows of special protection vehicles Work Procedures: 1. Connect the operating switch to the door wiring harness and partially raise the window \(not illustrated\) 2. Slacken and remove the upper nuts on both spacers 3. Carefully lift the window off the spacer and move it towards the rear against the rear window guide 4. Lower the window again and check the offset between the spacer and the mounting holes at the rear and front 5. Adjust the mounting at the rear \- The window must lie parallel against the rear guide along its entire length \- Undo the fasteners of the bracket on the window lifter \- Align the bracket with spacer to the bore in the window mounting, first in the longitudinal direction and then vertically \- Tighten the fasteners of the bracket/window lifter \(M6\) 12 \+ 5 Nm \- Fit the nut on the spacer at the top but do not tighten it 6. Adjust the mounting at the front \- Lift the window; it must lie parallel against the rear guide along its entire length \- Undo the fasteners for fore/aft adjustment \- Align the bracket with spacer to the bore in the window mounting, first in the longitudinal direction and then vertically \- Tighten the fasteners of the bracket/window lifter \(M6\) 12 \+ 5 Nm. Fit the nut on the spacer at the top and tighten it \(M6\) 12 \+ 5 Nm 7. Now tighten the nut on the rear spacer at the top \(M6\) 12 \+ 5 Nm 8. Check the movement of the window \- On the outside of the window, mark the position of the window relative to the rear window guide with tape \- Open and close the window several times \- The movement of the window should run parallel and uniformly along the guide, free of any tilting motion \- Repeat the adjustment procedure if necessary 9. To complete the adjustment, check the window for ease of movement. To do this, measure the power consumption of the window lifter motor. The maximum current draw is approximately 9 Amps while the window is being raised.

## The document

- [NHTSA's copy of the document (PDF)](https://static.nhtsa.gov/odi/tsbs/2025/MC-11013305-0001.pdf)
- [If that address does not open, try this one](https://static.nhtsa.gov/odi/tsbs/2025/MC-11013305-9999.pdf)

The document is the manufacturer's. This site does not hold it.

## Components

Electrical system

## Vehicles listed

- 2016 to 2019 MERCEDES\-BENZ AMG GLE43
- 2016 to 2019 MERCEDES\-BENZ AMG GLE63
- 2018 MERCEDES\-BENZ AMG GLE63S
- 2011 to 2015 MERCEDES\-BENZ AMG ML63
- 2018 to 2019 MERCEDES\-BENZ GLE 350
- 2018 to 2019 MERCEDES\-BENZ GLE 400
- 2018 to 2019 MERCEDES\-BENZ GLE 550 E
- 2016 MERCEDES\-BENZ GLE292 COUPE
- 2016 to 2017 MERCEDES\-BENZ GLE300D
- 2016 to 2017 MERCEDES\-BENZ GLE350
- 2016 MERCEDES\-BENZ GLE350D
- 2016 to 2017 MERCEDES\-BENZ GLE400
- 2016 to 2017 MERCEDES\-BENZ GLE450
- 2017 MERCEDES\-BENZ GLE550
- 2016 to 2017 MERCEDES\-BENZ GLE550E
- 2016 to 2017 MERCEDES\-BENZ GLE63S
- 2015 MERCEDES\-BENZ ML250
- 2011 MERCEDES\-BENZ ML320
- 2011 to 2015 MERCEDES\-BENZ ML350
- 2013 to 2015 MERCEDES\-BENZ ML400
- 2011 MERCEDES\-BENZ ML450
- 2011 to 2015 MERCEDES\-BENZ ML500
- 2011 to 2015 MERCEDES\-BENZ ML550
- 2011 MERCEDES\-BENZ ML63

JSON: [/v1/bulletins/11013305](/v1/bulletins/11013305)

[Report an error on this page](https://github.com/wenmar-pro/wenmar-open/issues/new?template=data_correction.yml&title=Data%20correction%3A%20Service%20bulletin%20LI72.10-P-069496&page=https%3A%2F%2Fopen.wenmarpro.com%2Fbulletins%2F11013305&vehicle=Service%20bulletin%20LI72.10-P-069496)