Service bulletin 01-009-24

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	11008418
Published by NHTSA	2024-10-04
Manufacturer's number	01-009-24
Manufacturer's date	2024-09-28
NHTSA component	ELECTRICAL SYSTEM; ENGINE
Manufacturer's system	Charging System

NHTSA's summary

Some customers may notice the charging lamp turns on while driving. Upon inspection, DTC P2502:00 PCM (Malfunction in voltage generated by generator) is stored in memory. This may be caused by resistance between the circuit board and ground. When high intensity electrical current passes through, the ground terminal position may not be sufficient enough. To eliminate this concern, the DC-DC converter control software has been modified. Additionally, the production procedure has been revised. The tightening torque for the ground terminal and circuit board was increased.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Electrical system, Engine

Trouble codes named

P2502

Vehicles listed
MAZDA MAZDA2	2021

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Other bulletins for the same vehicles and component
SA-041-26a	2026-10-03. Service bulletin. DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay™/ Android Auto™ will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button
SA-041-26	2026-07-03. Service bulletin. This SA supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-061/25 12/17/25 DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay™/ Android Auto™ will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button Example 1: Some electrical devices connected to the DLC-2 connector by insurance or mobile phone companies may cause: Battery discharge. The device may disrupt the CAN system battery saver mode. • IDS/MMDS will not communicate with the vehicle due to poor DLC-2 connection. The aftermarket device may cause DLC-2 female terminals to spread open.
SA-026-26	2026-05-05. Service bulletin. This Service Alert supersedes the previously issued M-Tip(s) listed below. The changes are noted in Red text. MT-002/19 09/30/19 and 12/19/19 DESCRIPTION If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage. Clean the intake manifold internally to remove any debris from old engine before installing the new replacement engine assembly. If the intake manifold cannot be properly cleaned internally, replace it.
SA-061-25	2026-01-04. Service bulletin. If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
SA-007-25a	2025-07-02. Service bulletin. The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. 2. CCA (Cold Cranking Amps): CCA ratings are normally located on a sticker affixed to the top of the battery to indicate a battery’s Cold Cranking Amps. CCA rated batteries are supplied with domestically produced vehicles. NOTE: If an incorrect CCA rating is entered into the Mazda DCA-8000, it will result
SA-007-25	2025-03-05. Service bulletin. The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
01-012-24	2025-01-04. Service bulletin. Some vehicles may exhibit the check engine light ON with DTC P0300:00 (Random misfire detected) stored. This may be caused by a mis-detection of a misfire due to improper PCM control logic. To eliminate this concern, the PCM control logic has been modified.
01-002-24a	2024-10-04. Service bulletin. Some customers may experience a check engine light illumination at idle while stopped with DTC P0300:00 stored, resulting in rough idle conditions. • P0300:00: Random misfire detected This concern is caused by improper engine control in the idle range. To eliminate the concern, the PCM control software has been modified.
SA-057-24	2024-09-04. Service bulletin. If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
09-038-24	2024-09-04. Service bulletin. In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer’s responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the “Speedometer Replacement Label”. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda’s vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO’s services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.