WenmarOpen by Wenmar Pro

Service bulletin 09-010-24

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id11001213
Published by NHTSA2024-06-07
Manufacturer's number09-010-24
Manufacturer's date2024-05-08
NHTSA componentENGINE
Manufacturer's systemLower Radiator Hose

NHTSA's summary

"Lower Radiator Hose Not Properly Seated Customers may experience the following: ● Engine coolant leak underneath the vehicle."

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Engine

Vehicles listed
JEEP GLADIATOR2023

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Other bulletins for the same vehicles and component
1132712026-07-18. Service bulletin. CORE – HEATER
1132702026-07-18. Service bulletin. CORE – HEATER
S26090000092026-07-02. Service bulletin. Check Engine Light (CEL) Illuminated with Diagnostic Trouble Code (DTC) P0106 Manifold Absolute Pressure Sensor Performance Setting In The Powertrain Control Module (PCM)
1128422026-07-02. Service bulletin. BOLT - HEX FLANGE HEAD
18-045-262026-04-22. Service bulletin. Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0300 - Multiple Cylinder Misfire (Active or Stored status set during cold start catalyst heating). ● P0301 - Cylinder 1 Misfire (Active or Stored status set during cold start catalyst heating). ● P0302 - Cylinder 2 Misfire (Active or Stored status set during cold start catalyst heating). ● P0303 - Cylinder 3 Misfire (Active or Stored status set during cold start catalyst heating). ● P0304 - Cylinder 4 Misfire (Active or Stored status set during cold start catalyst heating). ● P0305-00 - Cylinder 5 Misfire (Active or Stored status set during cold start catalyst heating). ● P0306-00 - Cylinder 6 Misfire (Active or Stored status set during cold start catalyst heating).** ● P08A6 - Gear Lever Position Sensor System - Multiple Sensor Correlation. ● P152F - Engine Hood Switch 2 / Engine Hood Switch 1 Correlation. ● P1129 - Closed Loop Fueling Not Achieved - Bank 2 Upstream. ● P0152-02 - O2 Sensor 2/1 Circuit High. ● P0158-02 - O2 Sensor 2/2 Circuit High. ● P2504 - Charging System Output High. ● P0563 - Battery/System Voltage High. Customers may also comment on one or more of the following: ● **The vehicle has a rough idle. ● The engine has a miss. ● Noisy valvetrain. ● "Service Transmission" message in the Instrument Panel Cluster (IPC) due to clutch slip detection with the transfer case in neutral. NOTE: Some customers may experience wheel spin or traction loss. In these situations, the Powertrain Control Module (PCM) may interpret the event as excessive clutch slip. To prevent potential clutch damage, a message may be displayed in the Instrument Panel Cluster (IPC).** ● Clutch is overheating. ● Clutch is slipping on engagement. M18 FSAR-TSB-7161 -2- ● Inability to accelerate uphill. ● Vehicle does not start. ● Vehicle is stuck in limp-home mode
S25090000092025-11-05. Service bulletin. Engine Oil Leak
91006702025-10-02. Service bulletin. Data collection required for all 2020-2026MY vehicles with 3.6L PSU engines during any of their first 3 engine oil changes. This data collection is applicable to all vehicle with engines with sales codes: ERG, ERC, EH3 and ERF. To assist with monitoring and quality improvement of the 3.6L engine, every time a vehicle comes for any of the first 3 oil changes, please use wiTECH to record the total engine idle time and the total engine runtime. 1. Prior to perform the oil change connect wiTECH diagnostic tool. 2. Navigate to the topology screen on the action item section. 3. Once the topology screen loads, disconnect wiTECH and continue with oil change.
S2509000001 REV.B2025-07-31. Service bulletin. Engine Rattle Noise
1056482025-07-23. Service bulletin. MODULE - ENGINE CONTROLLER
91006242025-07-17. Service bulletin. Verify Reman part number availability. Order the "R" part number for all orders: