# Service bulletin NTB19\-042E

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

- Type: Service bulletin
- NHTSA id: 11001208
- Published by NHTSA: 2024\-06\-07
- Manufacturer's number: NTB19\-042E
- Manufacturer's date: 2024\-04\-13
- NHTSA component: ELECTRICAL SYSTEM; FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING

## NHTSA's summary

AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

## The document

- [NHTSA's copy of the document (PDF)](https://static.nhtsa.gov/odi/tsbs/2024/MC-11001208-0001.pdf)
- [If that address does not open, try this one](https://static.nhtsa.gov/odi/tsbs/2024/MC-11001208-9999.pdf)

The document is the manufacturer's. This site does not hold it.

## Components

Driver assistance, Electrical system

## Vehicles listed

- 2019 to 2021 NISSAN ALTIMA
- 2024 NISSAN ALTIMA
- 2023 to 2024 NISSAN ARIYA
- 2017 to 2024 NISSAN ARMADA
- 2022 to 2024 NISSAN FRONTIER
- 2020 to 2022 NISSAN KICKS
- 2024 NISSAN KICKS
- 2018 to 2024 NISSAN LEAF
- 2016 to 2023 NISSAN MAXIMA
- 2015 to 2024 NISSAN MURANO
- 2016 NISSAN MURANO HYBRID
- 2022 to 2024 NISSAN PATHFINDER
- 2015 to 2024 NISSAN ROGUE
- 2017 to 2018 NISSAN ROGUE HYBRID
- 2017 to 2022 NISSAN ROGUE SPORT
- 2020 to 2024 NISSAN SENTRA
- 2020 to 2024 NISSAN TITAN
- 2020 to 2024 NISSAN TITAN XD
- 2020 to 2024 NISSAN VERSA
- 2023 to 2024 NISSAN Z
- 2022 to 2023 NISSAN redundant ALTIMA
- 2023 NISSAN redundant KICKS

## Recalls for the same vehicles and component

- [25V655000](/recalls/nhtsa/25V655000.md), 2025-09-30: ELECTRICAL SYSTEM:PROPULSION SYSTEM:CHARGING:MODULE:SOFTWARE; ELECTRICAL SYSTEM:PROPULSION SYSTEM:TRACTION BATTERY
- [24V748000](/recalls/nhtsa/24V748000.md), 2024-10-03: EQUIPMENT:ELECTRICAL:INFOTAINMENT:SOFTWARE; BACK OVER PREVENTION
- [24V700000](/recalls/nhtsa/24V700000.md), 2024-09-19: ELECTRICAL SYSTEM:PROPULSION SYSTEM:TRACTION BATTERY; ELECTRICAL SYSTEM:PROPULSION SYSTEM:CHARGING:MODULE:SOFTWARE
- [24V071000](/recalls/nhtsa/24V071000.md), 2024-02-02: BACK OVER PREVENTION: SENSING SYSTEM: CAMERA
- [23V628000](/recalls/nhtsa/23V628000.md), 2023-09-08: BACK OVER PREVENTION: SENSING SYSTEM: CAMERA
- [23V093000](/recalls/nhtsa/23V093000.md), 2023-02-16: ELECTRICAL SYSTEM:IGNITION:ANTI\-THEFT:IMMOBILIZER/PROXIMITY:KEY/SENDER
- [2022675](/recalls/tc/2022675.md), 2022-11-24: Electrical
- [22V875000](/recalls/nhtsa/22V875000.md), 2022-11-23: ELECTRICAL SYSTEM:WIRING
- [22V772000](/recalls/nhtsa/22V772000.md), 2022-10-13: BACK OVER PREVENTION:DISPLAY FUNCTION
- [22V527000](/recalls/nhtsa/22V527000.md), 2022-07-21: EQUIPMENT:ELECTRICAL:INFOTAINMENT:SOFTWARE; BACK OVER PREVENTION: SENSING SYSTEM: CAMERA

## Other bulletins for the same vehicles and component

- [NTB23\-048A](/bulletins/11031703.md), 2026-04-29, Service bulletin: ELECTRICAL SYSTEM. DTC P17F4 STORED IN THE TCM IF YOU CONFIRM The customer reports transmission vibration when accelerating, HINT: Vibration occurs during quick reacceleration after braking, during a 2\-1 downshift of the auxiliary gearbox. AND DTC P17F4 for “AUXILIARY GEARBOX \(CL JUDDER\)” is stored in the TCM. · If DTCs other than P17F4 are stored, this bulletin does not apply. Refer to the ESM for further diagnostic information. ACTION Refer to the Repair Overview on page 2 to determine if this bulletin applies. IMPORTANT: The purpose of ACTION \(above\) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
- [NTB15\-049CC](/bulletins/11031699.md), 2026-04-29, Service bulletin: ELECTRICAL SYSTEM. TELEMATICS SERVICE INFORMATION HINT: This bulletin applies to vehicles equipped with a 4G network compatible TCU. TCUs compatible with 3G network only are no longer supported. SERVICE INFORMATION The APPLIED VEHICLES that come equipped with a factory installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit \(TCU\). With an active NissanConnect® Services subscription, the TCU communicates with the NissanConnect® Services Data Center to provide various security and convenience services. This bulletin contains important service procedures that must be performed properly in order to set\-up and maintain the telematics system for the APPLIED VEHICLES. · A table has been provided on the next page that lists the steps required to successfully configure a TCU after it has been replaced. · A CHECK\-OFF SHEET has been provided on page 20 to print and check off steps as they are performed. Staple the completed CHECK\-OFF SHEET to the repair order.
- [NTB26\-003](/bulletins/11028686.md), 2026-02-10, Service bulletin: FORWARD COLLISION AVOIDANCE: WARNINGS; FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING. FALSE ACTIVATION OF AEB OR FCW IF YOU CONFIRM The customer states they have experienced false activation and/or unexpected braking of the Automatic Emergency Braking \(AEB\) or Forward Collision Warning \(FCW\) system, AND There are no related DTCs stored. ACTION Follow the SERVICE PROCEDURE in this bulletin to: 1. Confirm the current ICC/ADAS part number. 2. Reprogram the ICC/ADAS, if applicable. 3. Configure the ICC/ADAS. 4. Erase the DTCs. IMPORTANT: The purpose of ACTION \(above\) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
- [NTB25\-030A](/bulletins/11024395.md), 2025-10-21, Service bulletin: ELECTRICAL SYSTEM. STEERING WHEEL SWITCH BUTTONS INOPERATIVE, STICKING, OR NOT CLICKING WHEN PRESSED IF YOU CONFIRM The customer states that any of the steering wheel switch buttons are inoperative, sticking, or not clicking when pressed. ACTION Follow the SERVICE PROCEDURE to: 1. Remove the steering wheel assembly. 2. Replace the switch assembly on the steering wheel assembly. HINT: The switch assembly includes switches for both sides of the steering wheel. 3. Reinstall the steering wheel assembly. IMPORTANT: The purpose of ACTION \(above\) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- [NTB25\-014](/bulletins/11015917.md), 2025-03-25, Service bulletin: ELECTRICAL SYSTEM. REAR VIEW CAMERA IS INOPERATIVE OR "X" IS DISPLAYED WHEN SHIFTING INTO REVERSE IF YOU CONFIRM The Rear View Camera is inoperative or an "X" is displayed when shifting into reverse, AND There is corrosion at the Rear View Camera wiring harness connector D504 \(Figure 2 on page 2\). ACTION 1. Replace the Wiper Grommet Seal, the Rear Camera Harness, add Rear Camera Wiring Harness Dampers and, if there are signs of corrosion in the camera connector, the Camera. 2. Add Drain holes to the bottom of the rear door.
- [NTB19\-042F](/bulletins/11014472.md), 2025-02-25, Service bulletin: FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING; ELECTRICAL SYSTEM; SERVICE BRAKES. AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING APPLIED SYSTEMS: Vehicles equipped with a lane camera \(see Figure 1\) SERVICE INFORMATION If the Automatic Emergency Braking \(AEB\) warning light or is blinking \(but not illuminated steadily\) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: • When contamination or foreign material adhere to the lane camera viewing window on the windshield. • When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield. • When the lane camera viewing window on the windshield is temporarily fogged up. Figure 1 Nissan Bulletins are intended for use by qualified technicians, not 'do\-it\-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know\-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. HINT: o Refer to the applicable ESM for diagnosis if DTCs are present in the Laser/Radar, ICC/ADAS, or Lane Camera systems. o For further information: • Refer to the following pages. • Use the search keyword “blinking” in the ESM.
- [NTB19\-033G](/bulletins/11014471.md), 2025-02-25, Service bulletin: SERVICE BRAKES; FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL; FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING; ELECTRICAL SYSTEM. INTELLIGENT CRUISE CONTROL INOPERATIVE AND AEB/FEB WARNING LIGHT ON OR RADAR OBSTRUCTION MESSAGE DISPLAYED WITH DTC C1A16 OR C2582 IF YOU CONFIRM IMPORTANT: The purpose of ACTION \(on the next page\) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do\-it\-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know\-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. The customer states that the ICC stopped working while driving, OR The customer states that the AEB/FEB warning light is ON, or turned ON, while driving \(Figure 1\), OR The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving \(Figure 2\). AND DTC C1A16, C1A16\-97, C2582, or C2582\-97 is the ONLY DTC stored. Figure 1 Figure 2 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual
- [NTB25\-007](/bulletins/11014075.md), 2025-02-10, Service bulletin: ELECTRICAL SYSTEM; ENGINE. MIL ON WITH DTC P0196 STORED IN THE ECM IF YOU CONFIRM The MIL is ON with DTC P0196 for “EOT SENSOR” stored in the ECM. HINT: DTC P0012 for “INTAKE VALVE TIMING CONTROL B1” may be stored along with P0196 for “EOT SENSOR”. ACTION Follow the SERVICE PROCEDURE in this bulletin to diagnose DTC P0196 for “EOT SENSOR”. • Disregard P0012 if stored along with P0196. • Do not follow the service information in the ESM when diagnosing P0196. • The ESM information will be updated at a later date.
- [NTB25\-001](/bulletins/11013276.md), 2025-01-30, Service bulletin: VEHICLE SPEED CONTROL; FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL. CRUISE CONTROL/PROPILOT STOPS WORKING IF YOU CONFIRM The customer states that while driving on an unobstructed road, and on a clear day without any rain, snow, or direct sunlight, the Cruise Control/ProPilot stopped working, AND The Automatic Emergency Braking/Forward Emergency Braking light \(AEB/FEB\) flashed while the “Forward Driving Aids Disabled” message was displayed in the combination meter, AND DTC C2582\-97 for “Distance sensor” is stored as PAST. ACTION Follow the SERVICE PROCEDURE in this bulletin to: 1. Confirm the current LASER/RADAR part number. 2. Reprogram the LASER/RADAR, if applicable. 3. Erase the DTCs. 4. Perform Distance Sensor Alignment. IMPORTANT: The purpose of ACTION \(above\) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
- [NTB21\-040B](/bulletins/11013265.md), 2025-01-30, Service bulletin: ELECTRICAL SYSTEM. DTCS B2740\-87, B2744\-87, AND/OR B274D\-87 STORED IF YOU CONFIRM Any of the following DTCs are stored: • B2740\-87 \(TCU\) • B2744\-87 \(BCM\) • B274D\-87 \(Combination Meter\) ACTION Follow the SERVICE PROCEDURE to reprogram the Sonar Control Unit, if applicable. IMPORTANT: The purpose of ACTION \(above\) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

JSON: [/v1/bulletins/11001208](/v1/bulletins/11001208)

[Report an error on this page](https://github.com/wenmar-pro/wenmar-open/issues/new?template=data_correction.yml&title=Data%20correction%3A%20Service%20bulletin%20NTB19-042E&page=https%3A%2F%2Fopen.wenmarpro.com%2Fbulletins%2F11001208&vehicle=Service%20bulletin%20NTB19-042E)