WenmarOpen by Wenmar Pro

Service bulletin S2111000001 REV.B

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id11001043
Published by NHTSA2024-06-05
Manufacturer's numberS2111000001 REV.B
Manufacturer's date2024-05-31
NHTSA componentENGINE
Manufacturer's systemExhaust Manifold

NHTSA's summary

Customer complains of a brief metallic ticking/rattling/ringing noise after a cold start-up. It can be heard while standing outside the vehicle, resonating from the front wheel well areas. If the noise is present, it is normally heard at idle and the frequency of the noise will follow engine speed.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Engine

Vehicles listed
RAM 15002021, 2022, 2023, 2024

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
20232212023-04-13. Engine
20225842022-10-14. Engine
22V7670002022-10-13. ENGINE; FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
18-015-26 REV. A2026-10-16. Service bulletin. Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0300-00 - Multiple Cylinder Misfire - in Active or Stored status set during cold start catalyst heating. ● P0301-00 - Cylinder 1 Misfire - in Active or Stored status set during cold start catalyst heating. ● P0302-00 - Cylinder 2 Misfire - in Active or Stored status set during cold start catalyst heating. ● P0303-00 - Cylinder 3 Misfire - in Active or Stored status set during cold start catalyst heating. ● P0304-00 - Cylinder 4 Misfire - in Active or Stored status set during cold start catalyst heating. ● P0305-00 - Cylinder 5 Misfire - in Active or Stored status set during cold start catalyst heating. ● P0306-00 - Cylinder 6 Misfire - in Active or Stored status set during cold start catalyst heating. Customers may also comment on one or more of the following: ● Vehicle has a rough idle. ● Engine has a miss. ● Noisy valvetrain. This bulletin involves inspecting the vehicle and, if required, reprogramming the PCM with the latest available software.
18-015-26 REV. A2026-10-16. Service bulletin. Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0300-00 - Multiple Cylinder Misfire - in Active or Stored status set during cold start catalyst heating. ● P0301-00 - Cylinder 1 Misfire - in Active or Stored status set during cold start catalyst heating. ● P0302-00 - Cylinder 2 Misfire - in Active or Stored status set during cold start catalyst heating. ● P0303-00 - Cylinder 3 Misfire - in Active or Stored status set during cold start catalyst heating. ● P0304-00 - Cylinder 4 Misfire - in Active or Stored status set during cold start catalyst heating. ● P0305-00 - Cylinder 5 Misfire - in Active or Stored status set during cold start catalyst heating. ● P0306-00 - Cylinder 6 Misfire - in Active or Stored status set during cold start catalyst heating. Customers may also comment on one or more of the following: ● Vehicle has a rough idle. ● Engine has a miss. ● Noisy valvetrain. This bulletin involves inspecting the vehicle and, if required, reprogramming the PCM with the latest available software.
S2609000006 REV.A2026-10-07. Service bulletin. Customer indicates Malfunction Indicator Light (MIL) or Check Engine Light (CEL) coming on.
91008982026-09-17. Service bulletin. Engine PNs: MY 24-26 WD/DT (5.7L) Code P00B is being misdiagnosed and incorrect parts are being installed causing over repair. Refer to SOL S2609000006 The IAFM Foam Engine Valley Cover (PN 53013735AB) does not provide sufficient clearance for proper routing of the MDS solenoid jumper harness (PN 05148163AE). As a result, the harness may become compressed by the foam cover. To prevent unnecessary part replacement, the MDS solenoid jumper harness (PN 05148163AE) should be inspected for damage or pinch conditions prior to replacing the following part numbers: Engine PNs: 68409343AA 68409357AA 68450915AA OCV PNs: 53022338AB Phaser PNs: 53022298AA 53022298AB
S26090000092026-07-02. Service bulletin. Check Engine Light (CEL) Illuminated with Diagnostic Trouble Code (DTC) P0106 Manifold Absolute Pressure Sensor Performance Setting In The Powertrain Control Module (PCM)
91008392026-06-18. Service bulletin. 3-way valves are available in STAR Parts as two distinct components and must be selected correctly based on application. The High Temp 3-way valve (68309834AC) is located between the engine and the bulkhead at the rear of the engine compartment. The Low Temp 3-way valve (68448241AA) is located between the engine and the radiator at the front of the engine. When ordering or servicing, ensure the correct valve is identified and installed in the proper location, as incorrect part selection may lead to improper thermal system operation and repeat repairs.
S26090000062026-04-29. Service bulletin. P000B Bank 1 Cam 2 Position Slow Response - Malfunction Indicator Light (MIL) - Check Engine Light (CEL)
1114062026-04-22. Service bulletin. COVER - CYLINDER HEAD
1114052026-04-22. Service bulletin. COVER - CYLINDER HEAD
9100702Rev12026-04-15. Service bulletin. Camshaft cap bolts within the cylinder head assembly may cause damage to other components. DO NOT replace entire long block when only left OR right cylinder heads need to be replaced.